Question about Riso RZ220 Duplicator

1 Answer

Troubleshooting I have E003 when I try to do master on my TR 1510

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Your problem is with you clamping unit which is responsible for put the master on to the drum. Please check the unit for any phycial damage. You can also remove the old master on the drum your self and place back the drum into the machine and try asking the machine to make a new master. Good luck.

Donny Swann

Posted on Sep 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

E003 Error code in canon ir2420 photocopier


Code E003-0000 Description Abnormally low temperature (detected by main thermistor)
After the temperature detected by the main thermistor has reached the specified value, it does not reach the specified value during initial rotation. Remedy - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. Error Codes Canon iR2420 Code E003 0000

Oct 28, 2015 | Canon Printers & Copiers

1 Answer

E003 Switch the power on and off again


check if thermistors are ok/or replace them

If the fixing heater fails to operate.
• E002 or E003 is indicated.

Mar 22, 2010 | Canon NP 6050 Copier

1 Answer

My PSC 1510 does one of three things. It will either print just the top portion of a document and then it will trail off. If it's not doing that, it will print the whole document illegibly or not at all.


i am experienced that...

i suggest you try to go to your printer's application...

click troubleshoot...

there are groups of actions that you can do to check where your printer has the problem...

like for example..
the nozzle...
your paper tray..
you can try to align your nozzle ther..maybe thats the problem..

and also its good to refer for your manual..

you see the LED's of your printer are blinking right..

there have different types of blink's that the printer will do..each blink's correspond for errors..try to check it in your manual..

i hope i've help you...


Feb 08, 2010 | HP PSC 1510 All-In-One InkJet Printer

2 Answers

I have a problem with copier GP 225 it gives E003 how do I clear this code?


fuser temp not rising at correct pace. could be thermistor,thermal switch or fuser lamp

Oct 07, 2009 | Canon Printers & Copiers

2 Answers

System Error E000 and E003


E002 Error code details Heater temperature error (fails to reachspecific level; inadequate increase)


0000 The temperature of the fixing film is as follows:
1. has exceeded 100°C, but does not reach 115°C within 1 sec thereafter.
2. has exceeded 140°C, but does not reach 150°C within 1 sec thereafter.
3. has exceeded 160°C, but does not reach 165°C within 1 sec thereafter.

Main cause
 The fixing film unit is faulty (i.e., the main thermistor TH1 has poor contact, or the fixing heater is faulty). The main power supply PCB is faulty. The DC controller PCB is faulty.

Caution
 To clear the error, execute the following in service mode: COPIER>FUNCTION>FCLEAR>ERR.

Action
 See the description for E003. E003 Error code details Heater temperature error (abnormal drop; low-temperature detection)


0000 The main thermistor reading is lower than 140°C when paper is moved.

Main cause
 The fixing film unit is faulty (i.e., the main thermistor (TH1) has poor contact or has an open circuit; or, the fixing heater is faulty). The main power supply PCB is faulty. The DC controller PCB is faulty.

Caution
 To clear the error, execute the following in service mode: COPIER>FUNCTION>CLEAR>ERR.

Action
1. State
 Turn on the power switch, and clear E002/E003. Thereafter, turn off and then on the power switch. Does the fixing heater operate?
 NO: See "The fixing heater fails to operate."
2. Wiring
 Is the wiring from the DC controller PCB to the fixing film unit normal?
 NO: Correct the wiring.
3. Fixing film unit, DC controller PCB
 Try replacing the fixing film unit. Is the problem corrected?
 YES: End.
 NO: Replace the DC controller PCB.

Jul 28, 2009 | Canon imageRUNNER 2000 Copier

1 Answer

HP PSC 1510 keeps coming up with a misfeed


There may be a very small jam in the printer. Also, test with a different **** of paper. Put in one sheet to test.

Jun 11, 2009 | HP PSC 1510 All-In-One InkJet Printer

5 Answers

What does the error code E 01 stand for?risograph 4050


If its CR or TR, E-01 is main motor lock. turn off machine and hold reset button in while you turn the machine on again. Make sure your master removal unit and master feed unit are closed corectly.

Apr 07, 2009 | Riso RZ220 Duplicator

1 Answer

Canon NP-6612 copier Signal E003


E003 is fixing low temp error

please check thermistor and heater

Dec 04, 2008 | Sharp AL 1631 Copier

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Riso Printers & Copiers Experts

Marius Chiriac

Level 2 Expert

231 Answers

yadayada
yadayada

Level 3 Expert

60792 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you a Riso Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...