HI SENAO 2611CB3 DELUXE REPAIR IP DONT HOW TO RECOVERY IP IP 192.1681.1. DEFAULT NO ANSWER NO CONNECTION THANKS LOST DEFAULT IP SAMMY

The default username and password of router are admin and admin respectively. the default IP address is 192.168.1.1
The IP address varies with the manufacture of the company
Following are the IP of the companies

Manufacturers Default IP Addresses 3Com 192.168.1.1 Apple 10.0.1.1 Asus 192.168.1.1, 192.168.1.220 Belkin 192.168.2.1, 10.1.1.1 Buffalo 192.168.11.1 Dell 192.168.1.1 D-Link 192.168.0.1, 0.30, 0.50, 1.1, 10.1.1.1 Linksys 192.168.0.1, 1.1 Microsoft 192.168.2.1 Motorola 192.168.10.1, 20.1, 30.1, 62.1, 100.1, 102.1, 1.254 MSI 192.168.1.254 Netgear 192.168.0.1, 0.227 Senao 192.168.0.1 SpeedTouch 10.0.0.138, 192.168.1.254 Trendnet 192.168.0.1, 1.1, 2.1, 10.1, U.S. Robotics 192.168.1.1, 2.1, 123.254 Zyxel 192.168.1.1, 2.1, 4.1, 10.1, 1.254, 10.0.0.2, 0.138

Typically your router's ip has to be 192.168.1.1 or 192.168.1.254 and the credentials admin / admin. In case the router's ip is modified you can do this simple tip in order to locate the new one:
Connect your computer with ethernet cable at the router and after the connection has been established, hit start - run - type cmd. At the new black window type ipconfig and hit enter. You will get the results for ethernet connection (in case of a laptop you will get the wireless connection too). The line for Default Gateway is the router's ip address.

In case of a problem or clarification or further details needed, don't hesitate to post me a reply before rejecting my answer.
If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

Thanks and regards
Please kindly rate this solution
Stelios
direct fixya link: http://www.fixya.com/users/technical114

Start>Run>Type in CMD
Press enter
Type ipconfig
Note your gateway
Go to internet explorer and type your gateway in by itself. i.e. 192.168.1.254
Press enter
If this does not work attempt reattempt the gateway address but replace the last number with 254.
i.e. gateway=192.168.2.1 instead type in 192.168.2.254.

Hi. Here is the manual.

http://www.senao.com/images/www.senao.com_English/NL-2611CB3-PlusDelx-Manual-V1-0.pdf?CATNO0=D&CATNO1=D3&CNT=1

Set your PC to use the static IP 192.168.1.10, netmask 255.255.255.0.

To login to the web manager, go to http://192.168.1.1. Leave the username and password blank. You can now configure the device and assign IP address etc.

back side one reset button is there pull out the power cable then pull in that same time you have to press the reset button for three to five sec then all lied's blink all to gather then your default ip address is came then you again configure at default ip

1 ) Check if IP address is the correct address of your Gateway.
Check if you can ping.
Be sure you have your Java enabled
Some router requires a specific Browser (IE6 or IE7) and cannot respond to different browser.
Be sure to remove any Java protection from your Browser.
Check with user manual if IP address requires also a specific port number ( 8080 or other).
Be sure to Connect Router using Lan cable
2) Change your PC IP setting to same subnet as your router
Control Panel / Network settings / properties of TCP/IP define an IP address and a subnet mask compatible with Router as gateway.
3) If you are not sure of Router IP address use reset button on router back to factory default; use this to configure router.

repair center, visit : http://www.gblmedia.com

I do not know what you have for a DHCP server but some DHCP servers will show you what devices have been given IP addresses which you can use that information to find what address it is at now. Other than that you can use the guess and check method just going through IP addresses until the page comes up, you can use network mapping software to scan your network to find it or you can reset the access point to factory defaults where it will have the default IP address that you can then connect to and re configure it the way you want it.

if you hook your access point to your router the ip address is usually 192.168.0.50 Let me know how that works. It should take you to the access point page where it can be configured from there. I hope this is helpful to you

I assume you have the unit set to alocate ip addresses automatically in other words the dhcp is set to enabled in the settings. If so it maybe that the address is registering wrong, you can either click start>run> then type ipconfig /flushdns, or uninstal your wireless network card in device manager then restart the pc to automatically install it again as this will set it back to default, but remember to make sure obtain ip address automatically is enabled in the adapters properties on the tcp/ip properties.