Question about Kenwood Car Speakers & Subwoofers

1 Answer

Tried code 5227 for my kenwood mp522 without remote.is there another possibility?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 71 Answers

Hi kroy, another new one.
Call Kenwood customer Support.
They will either answer your question, If you have proof of purchase, or transfer you to the Parts Dept. to buy a new remote.( probably)
Regards Paul

Posted on Jun 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have lost the security code for my kenwood cd receiver. The model is KDC-MP4033S. Serial number is KE1202U0900623.


Hi,

Unfortunately Kenwood Radios can only be decoded on a bench and must be connected directly to specialist software. They cannot be decoded via serial alone. There is however a special procedure that can be used to bypass the security on these units using a master code 5227 (KCAR) which I will outline below.


Oct 15, 2011 | Car Speakers & Subwoofers

2 Answers

Ulock code kdc-mp5028


Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key
by Robotek

hope this helps...

Jul 30, 2008 | Kenwood Car Speakers & Subwoofers

1 Answer

Unlock code for Kenwood for MP 235 My remote does not work either. Is that because the unit is not unlocked?


Good Day,

KENWOOD SECURITY CODE CLEAR procedure

These codes are applicable for all Kenwood radios that do not have DVD or DVD screens located on unit.


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds

(so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio

stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key on the remote
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key on the remote

The security is canceled and the set enters the TUNER mode!

The above was pulled from:
http://forum.ecoustics.com/bbs/messages/4/134366.html

Hope this helps

Jul 05, 2008 | Kenwood Car Speakers & Subwoofers

1 Answer

I have a kenwood deck and it locked i can not use it it is a kdc-mpv6022


Good Day,

KENWOOD SECURITY CODE CLEAR procedure

These codes are applicable for all Kenwood radios that do not have DVD or DVD screens located on unit.


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds

(so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio

stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key on the remote
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key on the remote

The security is canceled and the set enters the TUNER mode!

The above was pulled from:
http://forum.ecoustics.com/bbs/messages/4/134366.html

Also try:

press reset use remote right after it loads press 552222777 then track forward do this with the remote open so you can use the numbers and make sure its in the audio mode the little switch on the side. prerty simple p.s. nothing will happen on the screen so dont stop pressing the code and press track forward you can now set the code to what ever 4 dig code you want in the set up screen

Also try: bypasse code of "2222"

Hope this helps

Jul 07, 2008 | Kenwood Car Speakers & Subwoofers

1 Answer

Need unlock code for kdc-mp825


Good Day,

KENWOOD SECURITY CODE CLEAR procedure

These codes are applicable for all Kenwood radios that do not have DVD or DVD screens located on unit.


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds

(so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio

stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key on the remote
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key on the remote

The security is canceled and the set enters the TUNER mode!

The above was pulled from:
http://forum.ecoustics.com/bbs/messages/4/134366.html
Also try:

press reset use remote right after it loads press 552222777 then track forward do this with the remote open so you can use the numbers and make sure its in the audio mode the little switch on the side. prerty simple p.s. nothing will happen on the screen so dont stop pressing the code and press track forward you can now set the code to what ever 4 dig code you want in the set up screen

Also try: bypasse code of "2222"

Jul 05, 2008 | Kenwood Car Speakers & Subwoofers

4 Answers

I HAVE A 5 YEAR OLD KENWOOD KDC-x569. I have a new car I'm putting it in and just realized the security system has locked. It was so long ago I put it in I have no idea what the code is. Is there a way to...


Good Day,

KENWOOD SECURITY CODE CLEAR procedure

These codes are applicable for all Kenwood radios that do not have DVD or DVD screens located on unit.


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds

(so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio

stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key on the remote
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key on the remote

The security is canceled and the set enters the TUNER mode!

The above was pulled from:
http://forum.ecoustics.com/bbs/messages/4/134366.html

Hope this helps

Jul 04, 2008 | Kenwood Car Speakers & Subwoofers

1 Answer

Factory code for Kenwood car stereo


5227

KENWOOD SECURITY CODE CLEAR procedure

These codes are applicable for all Kenwood radios that do not have DVD or DVD screens located on unit.


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds

(so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio

stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key on the remote
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key on the remote
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key on the remote

The security is canceled and the set enters the TUNER mode!

The above was pulled from:
http://forum.ecoustics.com/bbs/messages/4/134366.html

Hope this helps

Jul 04, 2008 | Kenwood Car Speakers & Subwoofers

1 Answer

Unlock code kenwood car stereo kdc-491


there are a few different ways to unlock according to model. I have posted 3 solutions.
1
During the code request mode, while holding the display key , press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

3
Press and hold the 1 then the 6 preset key. "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

This should unlock your radio.
Have a great day!

May 29, 2008 | Car Speakers & Subwoofers

3 Answers

I recently purchase vehicle with Excelelon KVT 817 DVD. Need Code


hi friend

take your dvd player nearest electronis & electronic store he will gave u same matching code of your dvd payer its came prise of code is $5 to 20$

thnx using fixya

Apr 13, 2008 | Car Speakers & Subwoofers

Not finding what you are looking for?
Car Speakers & Subwoofers Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Speakers & Subwoofers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Larry Spears
Larry Spears

Level 3 Expert

625 Answers

Are you a Kenwood Car Speaker and Subwoofer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...