Question about Sharp Projection Televisions

1 Answer

I have an Sharp Aquos flat screen tv and it is randomly 'blacking' out. The picture dissapears but there is still sound and i can still use the remote. I have it hooked up through a set top box, but there seems to be no problem with the set top box. Can anyone help?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

If the unit is still under warranty take it back for refund or replacement. If your tv is not under warranty, then you have a problem with the inverter board or the bulbs (ccfl) are bad. I have seen the inverter board and the bulbs be bad. Good luck to ya!

Posted on Jun 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am looking for base only for Sharp TV #LC65D93U. WHere I can find one?


Hello, the part # is CDAI-A368WJ01, and it's $233.00 everywhere I looked. If you will message me back on Tuesday, I'll see if I can locate a used on....tks

Sep 01, 2014 | Sharp LC-65D93U Refurbished AQUOS 1080p 65...

2 Answers

On my TV certain shows (Craig Furgerson, Oprah, The View)on different networks,a black rectangle, about 1/3 of the picture, appears. I cannot remove it.


That box appears to be from the close caption feautre. If you have the original remote you can disable using the menu and go to audio functions and look for close caption to turn it OFF.
Do you have the user's guide for this TV?
If you do not, could you provide the model number of your TV?

Jul 24, 2008 | Sharp Projection Televisions

1 Answer

I am repairing my sister TV {Toshiba TN61X81}. The original was no picture and with sound. Upon troubleshooting the vertical deflection, ihad move the screen control for all 3 crts to see the horinzontal...


The easiest way I have found to set the screen controls is to tune into an old black and white show, turn the green up until you see retrace then slowly turn it down until it just dissapears then adjust the blue and red for a true black and white picture.

Sep 08, 2009 | Toshiba TN61X81 61" Rear Projection...

1 Answer

TV Screen goes black


all tv has built in tuner inside,search for variables for inner tuner.when the signal is not fix naturally it goes black and white or destorted/blurred.

Oct 17, 2008 | Akai Projection Televisions

1 Answer

New Sharp Aquos LC37X20E. After 30 mins turns itself off to standby and comes back on after 2-5mins (even though the automatic return to stanby has been set to "disable"). Eventually after...


According to Sharp it is a software problem. Engineer came, installed software update ,10 minute job.....TV worked fine for 1/2 day unfortunately: Then images turned black and white in all channels TV turned itself off, and stanby and OPC buttons started flashing. When TV came back on its own 10 mins later , screen had 2 large square staines superimposed in image (as if it was a burnt screen)...Engineer will be back next week...all quite sad really for a new TV.....will keep u posted

Jul 03, 2008 | Sharp Projection Televisions

1 Answer

Sharp Aquos LC-20B6U-S TV NOW HAS NO SOUND OR PICTURE. IT APPEARS TO COME ON BUT WITH NO PICTURE OR SOUND.


This can be caused by many different things. Check power supply fuses. If ok suspect inverter board which drives screen. Check for bulging capacitors and open transformers or just find replacement cost using numbers on board. That may fixya.

May 29, 2008 | Sharp Projection Televisions

1 Answer

I just bought a Sharp Aquos LC-32D64U and a Box in the upper right hand corner keeps popping up "Air Analog Ch. 3 Audio Mono/Stereo." The audio keeps flashes either mono or stereo and it does...


The following pretains to most TV models:

Check to see if there is a key on the remote that is called "Display". This is normaly used to display the TV's operation status. Press it and see if you can work your way through different modes of the display content for the screen.

If you cannot make the statis dissapear, it is possible that there is a fault in the incoming signal and the TV is indicating this error, or it is possible that there is an actual defect in the set. At this point, I would contact the dealer. If you don't get a satisfactory answer, then you should contact Sharp service directly.

With retail dealers in many states and countries if you are dissatisfied with the set, you should be able to exchange the TV set in a specific period of time depending on the local laws that deal with consumer sales.


Jerry G.

Apr 13, 2008 | Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

Dave Naylor
Dave Naylor

Level 3 Expert

834 Answers

Jason Harris
Jason Harris

Level 2 Expert

256 Answers

Are you a Sharp Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...