Question about Epson DFX-9000 Matrix Printer

1 Answer

Printer is not aligning paper properly.

Print a bill of laden and it print one line down too far on the paper.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 94 Answers

Please try the following to resolved that issue:

1. Make sure the printer is turned on and the desired tractor is selected (the corresponding tractor arrow should be lit).
2. Open the upper cover.
3. Press the Top of Form button to enter top-of-form mode. The printer beeps once, and the Top of Form light turns on.
4. Use the Micro Feed buttons to feed the paper to the desired top-of-form position. The “A” on the ribbon protector shows you where the bottom edge of your first line of text will print. This position is based on the first printable line of text. If your software inserts a top margin of five lines, your text will actually print five lines below the top-of-form position.
5. Press the Top of Form button again to exit and save your new top-of-form position. Then close the top cover.

Posted on Jun 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have an hp 3150 all in one printer. Every time I turn it on to print a document it prints a test page. I am out of color ink so it doesn't print the additional numbers and lines to align the printer. I...


I know your problem and i want to know that have you changed or refill your cartridge?.

if yes
place one plain paper in the tray.
it will print the test paper
print it and place it on the scanner with the printed side down.
press the scan button from the printer
printer will blink the light for some time and stop blinking
now it didn't print test print every time you print

thanks

Jun 26, 2010 | HP PSC 1315 All-In-One InkJet Printer

1 Answer

Hi, replaced ink cartridge on Lexmark X2470. Now it goes as far as the "print alignment page" and freezes. Will not print the alignment page or any other page for that matter. Thanks.


Hello. The ink cartridge may not be seated properly in the carrier. Remove the cartridges from the printer. Close the cover. Clean the nozzles using a damp paper towel. Unplug the printer from the power source. Plug it back in after 10-15 seconds. When the printer asks for the cartridges, reinsert the cartridges. Also, make sure you're using the compatible ink cartridges for the printer. Let it print the alignment page all the way without cancelling it to align the cartridges properly. Hope this helps.

Mar 22, 2010 | Lexmark X2470 All-In-One InkJet Printer

1 Answer

Tops and bottoms of letters are cut off. I have changed the ink cartridge


Replace the old ink cartridge.
Verify that the unit is on. The On button is lit when the unit is on. If the device is not on, press the button to turn on the unit. Open the print cartridge door. The print carriage moves to the far right side of the unit. Wait until the print carriage is idle and silent, and then lightly press down on a print cartridge to release it. When replacing the tri-color print cartridge, remove the print cartridge from the slot on the left. When replacing the black or photo print cartridge, remove the print cartridge from the slot on the right. Pull the print cartridge toward you and out of its slot. If the print cartridge is being removed because it is low or out of ink, recycle the print cartridge. Remove the new print cartridge from its packaging. Remove the plastic tape by using the pink pull tab. Removing the Tape from the catridge.
  1. Will have Copper-colored contacts.
  2. Plastic tape with pink pull tab ( must be removed before installing ).
  3. Ink nozzles under tape
  4. The HP All-in-One prompts for an alignment of the cartridges every time a print cartridge is installed or replaced. Follow these steps to align the print cartridges from the control panel.
  5. Top & Bottom not printing properly.
  6. Load unused, plain, white letter, A4, or legal paper into the input tray
  7. If coloured paper is loaded in the Input tray when the print catridges are aligned, the alignment will fail. Load unused, plain white paper into the input tray when the Printer catridges are aligned, the alignment will fail. Load and unused plain white paper into the Input Tray and then try the alignment again.
    1. Press 6 to select Tools .
    2. Press 2 to select Align Print Cartridge The unit prints a print cartridge alignment sheet.
    3. Load the alignment sheet print-side down and top first in the center of the document feeder tray, and then press OK. Now the printer will print properly.

Jul 29, 2009 | HP Officejet 4315 All-in-One Printer

1 Answer

Colr prints showing plenty of lines


Here's a solution from Canon USA:

Issue: Banded or streaked prints
Solution: Print Head Alignment MP530

Perform Print Head Alignment Instructions to perform a Print Head Alignment directly from the machine. If diagrams or ruled lines are misaligned, print head alignment is required. The print head alignment can be performed automatically or manually. If the automatic print head alignment does not work, adjust the print head manually. Automatic Print Head Alignment
  1. Press <ON/OFF> to turn on the machine.

  2. Load a few sheets of letter-sized plain paper in the auto sheet feeder.

  3. Press the Open button to open the Paper Output Tray. Then open up and set the extension by pressing down the hollow on the front side.

  4. Execute automatic print head alignment.
    1. Press <COPY> button.
    2. Press <Menu> repeatedly to select [MAINTENACE].
    3. Press the left or right cursor to select [AUTO HEAD ALIGN], then press the <OK>. (A pattern is printed and the print head is automatically aligned. It takes about five minutes to finish printing the pattern.)

      05sj00165_02.jpg

Manual print head alignment
  1. Press <ON/OFF> to turn on the machine.

  2. Load two sheets of Letter-sized plain paper in the auto sheet feeder or cassette.

  3. Ensure that the proper paper source is selected.

  4. Execute manual print head alignment.
    1. Press <Menu> repeatedly to select [MAINTENACE].
    2. Press the left or right cursor to select [ALIGN PRINT HEAD], then press the <OK>. (The nozzle check pattern is printed.)

  5. Check the printed patterns and use the left or right arrow to input the number of the pattern in column A that has the least noticeable streaks.

    mp530_setvalue.gif

  6. Press <OK> to move the cursor to column B, and then use the left or right arrow to input the number of the pattern that has the least noticeable streaks.

  7. Repeat the procedure until you finish inputting the pattern number for column P.

    mp500_align_from_unit_1.jpg

  8. When you have finished inputting all pattern numbers, press <OK>.

    Note: For columns A through N select the patterns with the least visible vertical streaks. For columns O and P select the patterns with the fewest visible horizontal streaks.

    align_compare.jpg

    <1> Example of the pattern with the fewest visible vertical streak

    <2> Example of the pattern with the most visible vertical streak

    mp500_alignment_manual_3.jpg

    <1> Example of the pattern with the fewest visible horizontal streak

    <2> Example of the pattern with the most visible horizontal streak

Hope this helps - fotobean.

spacer.gif

Feb 21, 2009 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

Printer won't print properly.


Hi,


Please perform the following steps:

  1. Load unused plain white letter or A4 paper into the input tray.
  2. Press the Setup button.
  3. Press the down arrow button to select Tools and then press OK .
  4. Press the down arrow to select Align Print Cartridges and then press OK . An alignment page prints.
  5. After the success or failure message displays, click OK to continue. Recycle or discard the alignment page.


Regards,

Sagarjd

Nov 08, 2008 | HP Photosmart C4180 All-In-One InkJet...

1 Answer

Printer is printing off center


Doubleclick on that printer's icon, goto properties and select the advanced tab.
Click "Printing Defaults" and if you have the proper driver for this you should see a "paper/output" option
Write down the paper size.
Click on that line and a button will appear.
Click on that button and find the paper size you are using.
Now you can set you margins or change you paper size
Make sure you are using the proper units, the default entry is centimeters. You probably need inches

Oct 16, 2008 | Zebra Eltron LP 2824 Thermal Printer

1 Answer

Hpphotosmartc4380 the printing is badly out of line .How do yoy align the cartridges?


Hello,

You may want to run the alignment program again. Below are the steps as found on page 84 of the manual found here.

To align the print cartridges from the HP Photosmart Software
1.
In the HP Solution Center, click Settings, point to Print Settings, and then click
Printer Toolbox.
NOTE: You can also open the Printer Toolbox from the Print Properties dialog
box. In the Print Properties dialog box, click the Services tab, and then click
Service this device.
The Printer Toolbox appears.
2. Click the Device Services tab.
3. Click Align the Print Cartridges.
The HP All-in-One prints a print cartridge alignment sheet.
4. When prompted, ensure plain white letter or A4 paper is loaded in the input tray, then
press the button next to OK.
NOTE: If you have colored paper loaded in the input tray when you align the print
cartridges, the alignment will fail. Load unused plain white paper into the input
tray, and then try the alignment again.
The HP All-in-One prints a test page, aligns the print head, and calibrates the printer.
5. Load the page print side down on the right front corner of the glass, and then press
the button next to OK to scan the page.
When the On button stops flashing, the alignment is complete and the page can be
removed. Recycle or discard the page.

Oct 07, 2008 | HP Printers & Copiers

1 Answer

VERTICAL PRINT LINES


Check the front paper exit rollers for fit and alignment also the paper deck guides close to the planten area, if the printer is dropping print vertically down one side of the page, this can be caused by debris or anything that lifts the caridge assy the slightest bit, also check the print head seating and ribbin cable for proper alignment

Apr 04, 2008 | Canon PIXMA iP3300 InkJet Photo Printer

1 Answer

Not printing


printer print align paper one + sign and somthing __________line
after that put the your align paper in scanner assy. printer will
read data from your scanner assy and printer align cartridge itself

Feb 27, 2008 | HP PSC 750 All-In-One InkJet Printer

Not finding what you are looking for?
Epson DFX-9000 Matrix Printer Logo

439 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Printers & Copiers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Cindy Wells

Level 3 Expert

4755 Answers

Are you an Epson Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...