Question about Mintek DTV-373-D 37 in. LCD HDTV

1 Answer

No problem Could you please provide me with the exact width measurement of this unit, would greatly appreciate it. Thanks.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

37.3"

Posted on Jun 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Black and white vertical lines on left sided of screen. Black and white vertical lines vary in width. Left of vertical lines is wrapped video from right side. This is happening on all inputs. I have very...


If its under warranty take it back immediately!!! If not you will need to have the set diagnosed to pinpoint the problem. You could be looking at a faulty t-con/panel connection (easy fix) or a bad t-con board(inexpensive) or a LCD panel(very expensive) failure !

Oct 08, 2013 | Samsung UN60C6300 60 in LCD TV

1 Answer

I bought a Panasonic Quintrix TV but the guy did not have the manual which I need to set up. Can you please provide this. Thanks


Hi Andy,

May I know the exact model no. of your unit. It is printed at the back cover of your unit.

Jdvillanueva

Nov 21, 2011 | Flat Panel Televisions

1 Answer

When I plug the television in, it does not turn on. Instead I get the yellow indicator flashing not the red light. My television is 1 year old ( Hitachi L42X02PXW, 42" flat screen HDMI/LCD). Any help...


When troubleshooting these units, there are always several variables to consider. First check to see what last occurred with the unit such as did the children play video games, did the electricity go out due to bad weather. You may see that there are many possibilities but let's focus on what occurred last to the unit. Once we determine what happened last, we may isolate the actual cause of the problem. The actual cause may be associated with projection issues, older versions (Picture tube), interference from devices located nearby, and even a radio turned on and located really close to your unit. This is normally known as electromagnetic interference to electronics and is very common with the error you have provided today. Please continue to look for anything EXTERNAL to the unit before looking at the internal components, check your system input settings, verify your display settings, and confirm that your properly connected to your cable service.

Jan 16, 2011 | Hitachi 42HDM12 42 in. Plasma Television

1 Answer

JVC AV-56WP74 Convergence problem. I've read about convergence problems with the JVC AV-56WP74 and I am pretty confident my set needs the convergence board repair. You mentioned to another user that you...


Hi Dave


Thanks for using FixYa. If the issue is with the failed convergence (STK) ICs which needs to be replaced then, it’s not a difficult job if you want to do this yourself, you should require some basic knowledge about soldering-resoldering components. To start with you’ll have to open the back of the unit and then replace the ICs(STK ICs) which are located behind the black/gray heat sink and also check theresistors as if they are short the ICs might blow again after sometime. Please check this picture:
b0d4f31.jpg
And yes you are right there are repair kits available which includes repair instructions with the parts, if you want to do it yourself, you can buy and repair it yourself. Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Aug 17, 2010 | Flat Panel Televisions

1 Answer

No power to 42in tevion plasma tv, engineer says i need a psu assembly, where can i get one please. mike


The PSU is a Power Supply Unit and can be purchased online. In order to provide you with more exact information, a make and model for the set is required. Please add to this post that information so we can provide the order number, cost and location for purchase.

Thanks,
Dan

Jul 01, 2010 | Flat Panel Televisions

1 Answer

Power suppy akai lct2715 componant breakdown


Hi Phil,
The value R11 is 8.2K ohms. It's surface mount but I'm not sure about the package size. You can measure one that looks like the same size as the missing resistor. Measure the width and length in inches with a digital caliper if available.
Use this sample to decode the package size:
0805 (2012 metric) : 0.08" × 0.05" (2.0 mm × 1.25 mm) Typical power rating for resistors 1/10 or 1/8 watt.

Dec 29, 2009 | Akai LCT2716 27 in. LCD Television

2 Answers

Tryiny to put my Akai LCT3201AD TV on the wall


For a set this size, there should be at least 4 mounting holes for a wall bracket. Please note that wall mounting is an option so the holes may be covered by plastic caps to hide the holes. These holes should be in a box shape around 1 foot wide or so.


Dan

Apr 10, 2009 | Akai LCT3201AD 32 in. LCD Television

1 Answer

Attaching 26 " lcd to stud wall


12 inches is the minimum for mounting the unit to the wall. I mounted a 42 inch LCD using a Sanus tilt (non-swivel) mount from Best Buy. We mounted it on wooden beams exactly 12 inches apart. Works great!

Mar 05, 2008 | Flat Panel Televisions

Not finding what you are looking for?
Mintek DTV-373-D 37 in. LCD HDTV Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mintek Flat Panel Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

Brad Brown

Level 3 Expert

13531 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Are you a Mintek Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...