Question about HP 800/PARTS/N4000 SYSTEM BOARD B VERSION HP (A363969706) Motherboard

1 Answer

MOTHER BOARD i have a hp d240 system board i have ami bios chip it gives me 10 beeps and then cuts off i replaced the cmos chip and i still have no clue my teacher threw me on this project and i have no clue about computers please help

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 49 Answers

You need to have a bootable disk that has the bios for that specific motherboard on it and you need to flash it. Why dont you go to the HP website and look up the model number, it will tell you specific hardware in your system and also you can download the bios, bios updating software and you should alos find information on how to properly update the bios. Never ever restart your computer during bios update, it will f23ck it up.

Posted on Jun 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cmos beep codes


do you know which bios your computer is running ?

AMI BIOS beep codes 1 beep - DRAM refresh failure
2 beeps - Parity Circuit Failure
3 beeps - Base 64K RAM failure
4 beeps - System Timer Failure
5 beeps - Processor Failure
6 beeps - Keyboard Controller / Gate A20 Failure
7 beeps - Virtual Mode Exception Error
8 beeps - Display Memory Read/Write Failure
9 beeps - ROM BIOS Checksum Failure
10 beeps - CMOS Shutdown Register Read/Write Error

Phoenix BIOS BEEP codes. 1-1-3 CMOS write/read failure.
1-1-4 BIOS ROM checksum error.
1-2-1 System timer failure. (Programmable Interval Timer PIT)
1-2-2 DMA (direct Memory Access) failure.
1-2-3 DMA page register failure.
1-3-1 RAM refresh failure.
1-3-3 64K RAM chip or data line failure.
1-3-4 64K RAM odd/even logic failure.
1-4-1 64K RAM address line failure.
1-4-2 64K RAM parity error.
2-?-? Any beep series starting with 2 beeps indicates a 64K RAM chip or data line error.
3-1-1 Master DMA register test.
3-1-2 Mslave DMA register failure.
3-1-3 Master interrupt mask register failure.
3-1-4 Slave interrupt mask register failure.
3-2-4 Keyboard controller failure.
3-3-4 Screen (video) memory failure.
3-4-1 Screen initialization failure.
3-4-2 Screen retrace failure.
4-2-1 Timer tick interrupt test failure.
4-2-2 Shutdown test failure.
4-2-4 Unexpected interrupt in protected mode.
4-3-1 RAM test failure above address 0FFFFh (64K +)
4-3-3 Interval timer channel 2 test failure.
4-3-4 Time of day clock failure.
4-4-1 Serial port test failure.
4-4-2 Parallel port test failure.
4-4-3 Math Co-processor failure.
BEEP codes may vary dependent upon the revision of BIOS. This list is for reference only

hope this helps

Oct 10, 2012 | Intel Mother Board S5520HCR (988889365963)...

4 Answers

Five long beeps at a range of five seconds then, repeats


Five long beeps for a modern motherboards indicates a processor failure. If you wish to remove the processor and re-seat it (reconnect it to see if it begins to work again) make sure to get some thermal compound to put between the CPU chip and the heatsink. More info at: http://www.hardwaresecrets.com/article/How-To-Correctly-Apply-Thermal-Grease/274
POST AMI BIOS beep codes
  • 1 - Memory refresh timer error
  • 2 - Parity error in base memory (first 64 KiB block)
  • 3 - Base memory read/write test error
  • 4 - Mother board timer not operational (check all PSU to MB connectors seated)
  • 5 - Processor failure
  • 6 - 8042 Gate A20 test error (cannot switch to protected mode)
  • 7 - General exception error (processor exception interrupt error)
  • 8 - Display memory error (system video adapter)
  • 9 - AMI BIOS ROM checksum error
  • 10 - CMOS shutdown register read/write error
  • 11 - Cache memory test failed
  • 12 - Mother board does not detect a RAM module (continuous beeping)
Source: Wikipedia

Feb 28, 2011 | Motherboards

2 Answers

What does a AMI bios beep code of one long and 9 short


AMI BIOS beep codes Below are the AMI BIOS Beep codes that can occur. However, because of the wide variety of different computer manufacturers with this BIOS, the beep codes may vary.
Beep Code
Descriptions
1 short DRAM refresh failure 2 short Parity circuit failure 3 short Base 64K RAM failure 4 short System timer failure 5 short Process failure 6 short Keyboard controller Gate A20 error 7 short Virtual mode exception error 8 short Display memory Read/Write test failure 9 short ROM BIOS checksum failure 10 short CMOS shutdown Read/Write error 11 short Cache Memory error 1 long, 3 short Conventional/Extended memory failure 1 long, 8 short Display/Retrace test failed

Jun 01, 2010 | Asrock 939SLI32-eSATA2 (939SLIESATA2)...

1 Answer

Bad bios flash, backup gives bad checksum error. downloaded correct ver - still bad checksum. what should I do? AMI bios ver 1.0


Is the mother board working? If so, why are you flashing the bios? If the bios is bad and can not be flashed, you may be able to buy a pre-flashed chip if it uses a removable flash chip. Try this site but you can find others on the Internet.

Mar 24, 2010 | Intel Motherboard

1 Answer

I have a series of 10 beeps every few minutes. What does this mean?


10 Short Beeps Your problem lies deep inside the CMOS. All chips associated with the CMOS will likely have to be replaced. Your best bet is to get a new motherboard. (for AMI BIOS)

Oct 26, 2009 | ASUS M2N32-SLI Deluxe/Wireless Edition ATX...

1 Answer

Sashasantiago87@yahoo.com


Your problem lies deep inside the CMOS. All chips associated with the CMOS will likely have to be replaced. Your best bet is to get a new motherboard.

Jun 10, 2008 | ASUS P4PE Motherboard

1 Answer

Cant insall new graphics card


the graphic card is a plug and play device meaning as you install it, it is giving its resource and it starts working but you install yours and the motherboard beeps means
1. there was a change in the CMOS configuration which should not occur
2. the CMOS utility did not identify any graphic device
i think your graphic device is questionable it could not be good is the word.



UZOWUANYA
e-mail:uzowuanya@yahoo.ca

Feb 14, 2008 | ASUS Intel 810 Chipset MEW-AM Motherboard

1 Answer

Will not boot all I get is 0ne long beep


Replace the memory, as this can give you a fault on it's own if not fitted. Reset the cmos by shorting the CLRCMOS jumper or the JBAT1 terminal on pins 2-3, then back to pins 1-2 on the mobo, and try again. If you can get in the cmos and set the time and date etc, yet you still get the beep there could be a processor problem, but if it freezes in the cmos set up then you will have bios chip fault, so take back the whole kit to your supplier, as he may wish to try it himself first before replacing.

Mar 26, 2007 | MSI K8N Neo3 Motherboard

Not finding what you are looking for?
Motherboards Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Motherboards Experts

Cindy Wells

Level 3 Expert

4751 Answers

SHAMUN

Level 1 Expert

14 Answers

Steve

Level 3 Expert

3287 Answers

Are you a HP Motherboard Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...