How do you program the remote to the car? - Excalibur. K9-ECLIPSE 2-Way Keyless Entry & Security System with Proximity

1996 Roadmaster

1. Locate the programming connector located in the LH trunk. Trim may have to be pulled back to access programming connector. ( Connector has black/white wires leading up to it and it is not connected to anything.)
2. Jump programming connector terminals. Leave terminals jumped unitl step 6.
3. System should now lock and unlock doors to indicate programming mode has been entered.
4. Press any button on keyless remote once. System should now lock and unlock doors, indicating successful programming of keyless remote.
5. Repeat step 4 for additional remote or other existing keyless remote. NOTE: A maximum of only two Keyless Remotes can be programmed.
   
6. Remove programming connector jumper wire to exit programming mode.
7. Test remote(s).

It has to be programmed .
Remote Transmitter Programming NOTE: All remote transmitters are programmable and must be set at the same time.

1. Turn the key from OFF to RUN four times within three seconds, ending in RUN. The locks will then lock and unlock, confirming program mode has been entered.

1. Press any button on each remote transmitter to be programmed. The doors will lock and unlock to confirm that each remote transmitter has been programmed.

1. If additonal remote transmitters are to be programmed, repeat Step 3 within 7.5 seconds or steps 2 and 3 if more than 7.5 seconds have elapsed.

1. To exit program mode, turn the ignition to START or wait 7.5 seconds.

1. NOTE: Failure to wait at least 20 seconds will cause programming failures.
   Wait at least 20 seconds after turning the key to OFF or after the last remote transmitter has been programmed to activate a remote transmitter for testing or verification.

wrong remote.
Pcm has many rules for programming the fob.
im not looking yours up, (you can at the FSM link below for 4 bucks)
1: wrong remote
2: too many remotes programmed,(some have 8 limit)
3: some cars (newer) takes 2 good remotes to make a 3 or more..
see how rules matter (logic in the PCM) varies by maker and year, on all cars made......

USA spec, cars, we are USA forum. so....

https://suzukipitstopplus.com/Products/10218-2000-vitara-grand-vitara-service-manual.aspx


there it is , read how the IMMO works and door fobs program.

Have all the remotes you want to program with you, you can program upto 4...turn key from off to on 8 times withn 10 seconds,stoping in the on position,door locks will cycle to confirm it's in learn mode, press lock button on remote and door locks will cycle once to confirm remote is programmed. ..then press lock button on remaining remotes one at a time to program them...shut key off and try remotes...on 4 remotes are allowed. .when you do this all other remotes that you don't havr with you will not work.

1. Enter 5-digit permanent entry code into the keyless entry keypad.
2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors will lock then
unlock confirming you are in programming mode.
3. Press any button on first Keyless Remote within 5 seconds of pressing the 1/2 button. Locks will
cycle to indicate succesful programming.
4. If you are programming more than one Keyless Remote (Including any exsiting remotes) Press
any button on second keyless remote within 5 seconds of previous remote. Locks will cycle again
to indicate succesfull programming. (If the keypad light goes out before all remotes are
programmed the entire process must be repeated).
5. Press the 7/8 and the 9/0 buttons simultaneously on the keypad to exit program mode.

Great news, you can program a 1994 Lincoln Town Car keyless entry remote yourself! Here are the steps:

NOTICE: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
1. Turn ignition to RUN or ACC.
(Run is forward, just shy of starting car.)
2. Momentarily jump pins in programming connector located behind the glove box.
(The connector will have two pins inside of it, and it will not be plugged into anything. Jumping the pins means to make a connection between the metal inside the plug. You can do this by using any metal, a metal paperclip bent in the shape of a "U" usually works perfect.)
All doors will lock then unlock to confirm programming mode.
3. Press any button on first keyless remote. Door locks will cycle to confirm programming.
4. If programming a second keyless remote, press any button on second keyless remote. Door locks will cycle to confirm programming.
5. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
You can find more keyless entry remote programming instructions here https://www.keylessentryremotefob.com/Key-Fob-Programming-Instructions-s/1856.htm

If you have a working remote the programming is as follows:
1. Turn the ignition switch to the 'run' position.
2. With the remote that works, press the UNLOCK button for 4 to 10 seconds.
3. Within that 4 to 10 second period, keep holding the UNLOCK button, and press the PANIC button for one second. Release both buttons. You will hear a chime, this means that the car is in remote programming mode.
4. Within 30 seconds of hearing the first chime, press any button on ALL remotes to be programmed (including the working remote). You will hear a chime after each remote is programmed.
5. Turn the ignition key to OFF.
6. Test all of the remotes.

If you don't have a working remote, you will need to go to a dealership to have them program one for you.

You should see three buttons on the driver sun shade. Let's name them from left to right 1,2, and 3. Start by clearing any old codes. To clear codes press buttons 1 and 3 simultaneously until the light starts blinking. Release the buttons simultaneously. Before starting to program the car remotes you must have your gate hand held remote ready with a good charged battery. Now, to program your first gate car remote let's choose button 1. Press button 1 until it start blinking (about 20 seconds). Keeping button 1 pressed, activate your hand held remote close (about an inch) from the car button 1, until the light blinks faster than before. Release both remotes simultaneously. You are done programming your car remote button 1. For two additional gates remote controls programming repeat the procedure with button 2 and then with button 3.

For most Ford vehicles you can self-program the remote for keyless entry. However there are some of the newer models that require professional equipment to program the keyless entry remote. You can check out what vehicles have self programming and which ones need professional programming here: https://www.keylessentryremotefob.com/Key-Fob-Programming-Instructions-s/1856.htm

In the meantime here are the most common Ford Keyless Entry Remote programming instructions:

*** THERE ARE 2 POSSIBLE PROGRAMMING PROCEDURES. ***Procedure #1Note: Obtain all remote transmitters for this vehicle.
Note: Do not depress the brake pedal during procedure.

1. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
2. Within 20 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 4.
3. Within 20 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 3. For all other remotes.
4. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
   
   Procedure #2Note: Obtain all remote transmitters for this vehicle.
5. Fasten seat belts and close all doors.
6. Turn ignition from OFF to RUN 4 times within 6 seconds, with the 4th time ending in RUN. (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
7. Turn ignition to OFF. Acoustic signal will sound and system warning lamp will illuminate to confirm programming mode.
8. Within 10 seconds, press and hold any button on the first keyless remote. Wait for acoustic sound and warning lamp to flash (confirming programming) then release button on remote. Wait 2 seconds but within 10 seconds repeat step 4. For all other remotes. If you only have one remote then continue to step 5.
9. Turn ignition to Crank or wait 10 seconds to end programming mode.

1. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in
RUN. Door locks will cycle to confirm programming mode.
2. Within 20 seconds press any button on first keyless remote. Door locks will cycle
to confirm programming.
3. Within 20 seconds, press any button on second keyless remote. Door locks will
cycle again to confirm programming.
4. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.