Question about BenQ FP731 17" LCD Monitor

1 Answer

Can't find video signal

On power up, Power LED lights green, "BENQ" is displayed for >2s. After 4s message displays "Signal Cable Not Connected" for >250ms, screen goes blank and Power LED lights amber. All Buttons on Monitor non functioning except power off. Cycle power button and cycle repeats.
I have resoldered Transformers T751, T752, T753, T754 and Transistors Q739, Q740, Q743, Q751, Q759, Q760.
Can you help any further.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 220 Answers

If screen says "Signal cable not connected " all the time till power led switches to Amber chances are monitor is ok and problem is with graphic card or cpu.Connect to Known working CPU and confirm that monitor is the problem.
If same problem persists on another working cpu after changing signal cable,the interface board in the monitor could be defective.
Samir

PLease rate solution and provide feedback.

Posted on Jun 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lcd tv troubleshooting


Check for power supply trouble. The green LED on the front panel should light if power is getting to your TV. The "no signal" indication may mean no antenna or cable input is detected

Aug 21, 2013 | Televison & Video

1 Answer

ON SCREEN HAD POWER ONLY V8.02.8


FOLLOW this instruction and fix it. God bless you
·
Connect the component video, HDMI1 or AV1 cable from the component device (such a DVD player) to the appropriate input port on the TV. This port may say "Video IN" on the back of the TV. Ensure that the cable is connected securely at both ends.
· 2
Use the remote control's device button(s) to access the menu and select the input through the menu that matches the type of cable input connected to the back of the TV. For example, if you connect the cable to the HDMI1 input port on the back of the TV, selecting anything but the HDMI1 option with the remote control may cause the "No Display" message to appear, which usually means that the TV is not receiving a signal at the connection input you have selected.
·

· 3 Turn the power on to the component you want to view. If the power was off, turning it on will activate the display and replace the "No Display" message.
· 4
Test any other connected components at their selected inputs to see that the TV is receiving the video signal properly from those sources.
· 5
Check with your cable or satellite provider if their set-top box is the source of the "No Display" message and is powered on, to see if the problem is caused by a disruption in their service. If using an antenna, adjust the antenna and re-scan for available channels.

Jul 20, 2013 | LG 55LE5400 55IN LED HDTV 1080P 120HZ 4...

1 Answer

I have a synaps monitor model mt9bbk. The screan will go black and power led will flash.


Display Power management is being triggered because no input signal was detected. Verify that the video source is connected and on. (Computer, notebook, etc).
- Try another computer or laptop that you know is working properly.
- Do you see any change on the screen if the display cord is completely disconnected (often a "Test" or "Check Cable" message appears). - Inspect the signal cable from the monitor - worn? Any places where the cable was bent to an extremely small (acute) angle? (less than 75 degrees?) Try gently moving the cable around at either end and see if you get a partial signal on the screen (while connected to the computer). If you do, the signal cable is damaged, if possible replace it. try: www.monoprice.com

Apr 14, 2011 | Computers & Internet

1 Answer

Samtron Monitor 56V Display Problem


your power supply is probably bad. open the case with it unpugged and look for leaking or crowned capacitors. most electronic repair shops can replace them for you

Jan 10, 2010 | Computers & Internet

1 Answer

When I power on I get a green light on the monitor


Monitor is not geting the signal from the PC.
connected the monitor to the AVG port on the rear of the PC and see if you get the monitor to go up. if not, try to get a video card.

Jan 12, 2009 | HP Compaq d530 PC Desktop

2 Answers

Green light continously blinking in samsung sync master 753s


1. cpu problem. why because of there is no signal output from cpu to monitor. the led blinking means there is no vertical, horizontal signals from cpu to monitor.

2. your monitor connected to another system.

3. neck board dry points.

4. cheak the display cable. 13&14 pins are horizontal, vertical signals.1, 2, 3 pins , R G B , 6 ,7, 8 pins R G B ground ( coaxiler cable used , meshed wire is ground )

Oct 13, 2008 | Samsung SyncMaster 753S 17" CRT Monitor

2 Answers

"No signal detected" when LCD connected with DVI-D Cable


Thank you for providing your configuration details.
You have failed to specify wheather or not your LCD Display is under Warrenty.

Perhaps these simple trouble shooting procedures will get the job done.

1. use the DVI to VGA adaptor that came with your card

Plug in a regular CRT monitor to the Primary Display Output Port using the DVI to VGA adaptor
( either port can be designated as the primary by you )
I like to use the Port nearest to the motherboard as the Primary

2. plug in the your LCD monitor on Secondary Display port using your DVI cable

At this point you should be able to see your desktop on the Primary CRT Display

3. Go to the display properties and use the Nvidia Dual Display Setup Wizard

set both desktops to CLONED at a resolution of 1024x768 and set the refresh to 60Hz
which is default for most LCD displays , some have higher refresh rates , consult your user manuel

If the display resolution and refresh are set incorrectly for your CRT or LCD you will see
Signal Out of Range ( if the display has the ability to display that error message )

At this stage both displays should be showing a Windows Desktop

If you now see your desktop on both displays , you can now put the LCD on the Primary Port



No Signal Detected ( this means the display device is not receiving a signal )

If your LCD display is still displaying the error message
"No Signal Detected" after performing the trouble shooting proceedures
You may need to read the user manuel about how to enable DVI signal input.

If you are certan you have done everything correctly but still see only "No Signal Detected"

Your LCD Display may need replacement

Loch Hime :-)

Sep 14, 2008 | BenQ FP71E 17" LCD Monitor

1 Answer

No signal on first boot


I think is a power supply problem,,

Mar 10, 2008 | Nokia 445 Pro 21" CRT Monitor

1 Answer

Power ok but No Display


see this one
http://www.fixya.com/support/t155971-benq_t701_lcd_monitor

Sep 16, 2007 | BenQ T701 TFT 17" LCD Monitor

2 Answers

No display


if your monitor is not connected to a pc, then it cannot find a vga signal input and therefore go into power saving mode, which is indicated by the orange light, but as soon as you connect to the pc and power on the light will go green and the monitor will power up.

May 07, 2007 | BenQ T701 TFT 17" LCD Monitor

Not finding what you are looking for?
BenQ FP731 17" LCD Monitor Logo

383 people viewed this question

Ask a Question

Usually answered in minutes!

Top BenQ Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Tony

Level 3 Expert

2599 Answers

Computer Links

Level 3 Expert

2385 Answers

Are you a BenQ Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...