Question about Hotpoint WMA35 Front Load Washer

3 Answers

HOTPOINT WMA35 WASHER

I've fitted a new control board and pressed a wrong button when configuring the board to the model. Now the lock light flashes and it goes on to drain only. How do i clear the board and start again URGENT thanks.

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 3,422 Answers

HI,

You could try 3 things:

1 Find the button on your panel which has the 'key' symbol, press and hold this down till the lock light goes off.

2 Hold down 'options' & 'select' buttons together till the light goes off.

3 Press 'end of cycle' button for 3 seconds, lock should come off.

Goodluck,
Please don't forget to rate or accept the solution

Posted on Jun 09, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,614 Answers

Try to unplug the unit for an hour to reset the system... if this not work try to disconnect the new installed panel board again...

micro

Posted on Jun 09, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 1,894 Answers

Do a hard reset and check

Posted on Jun 09, 2008

  • dewan nafees ahmed Jun 09, 2008

    else remove the board from the system and reinstall it again fully in a new manner.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Door locked light flashes which prevents it from working


hi if your interlock is playing up this will cause this try giving a bit of push on door were catch is dont slam door if light stops flashing doors locked its good idear change interlock to do this take band from round door rubber pull rubber of rim take two screws out interlock you can get it through the gap unplug put new on should be ok then but try a push on door 1st when doing lock unplug machine hope tis helps

Jan 24, 2014 | Hotpoint WMA35 Front Load Washer

1 Answer

Hotpoint WMA33 washer- The machine was in a final spin after a 95 degree wash when the power to the house was tripped by the washing machine, since then the machine will not start, all the lights come on...


Possible the surge would have made some changes in the main processor memory or damaged the processor. You can shut down the washer and remove the plug for few hours. press down all the panel buttons to drain all residual voltage on the board.
If the same fault repeats then it is possible there are errors on the board.

Jul 25, 2012 | Hotpoint Washing Machines

1 Answer

Hi, I've just done a wash on my Hotpoint WMA35 but it will not do the spin cycle. I hear the usual whirring sound as if the spin is about to start, but it doesn't. I've rearranged the load but still...


Any flashing lights or extra solid lights on the control board? By "spin cycle", do you mean the final spin cycle and drainage of water through waste pipe (basically, I want to know if the washer spins then fails, or fails to begin any rotation of the drum whatsoever). I'm having problems with my WMA35 myself, so it'd be interesting to see if this a common fault.

Feb 07, 2011 | Hotpoint WMA35 Front Load Washer

1 Answer

Wma44 hotpoint washer. Did a wash as normal and


Sometimes a weak or broken spring in the door handle can be the cause of the problem, but you would have to take the door apart to check this.
If you have already fitted a new door lock, then chances are it is the control board, but I would check the door handle first.

Jan 30, 2010 | Hotpoint WMA44 Front Load Washer

1 Answer

My washing machine has just stopped working and the on/off light and the mini load light are flashing rapidly any ideas???? make ..hotpoint, model...WF560


TRY HOLDING IN THE SIGNAL LITE FOR 3 SECONDS AND THAT SHOULD TURN THE LITES OFF AND OR THE CONTROL LOCK LITE OFF ALSO!! GOOD LUCK

Jun 03, 2009 | Hotpoint WMA35 Front Load Washer

2 Answers

Door will not lock on my Hotpoint Aquarius WMA35 1100 Spin


i would get a new door or catch from the hotpoint website hope this helps

Jan 24, 2009 | Hotpoint WMA40 Front Load Washer

1 Answer

I have only bcold water feed but washer has hot/cold do i need 2


If it is a hot and cold fill m/c, what you need is a fitting that is referred to as a" Y" piece..To fit it, connect the straight leg of the "Y" piece to the cold supply tap, and then fit a hose to each of the two outlets, connecting each of these to the 2 inlets on the valve to the washer..
It will then fill with water, regardless of the programme you select.
You can purchase the "Y" piece connector from most hardware shops, or B&Q, and the like.
Plz rate my solution.
Thanks.

Jan 12, 2009 | Hotpoint WMA35 Front Load Washer

2 Answers

On a hotpoint aqualtis aqxx149pm i get error code f8 flashing


Hi.
F8 means that heater relay cannot be activated, you need to call an engineer.
Could be expensive, possibly a new control board needed

Nov 19, 2008 | Hotpoint WMA35 Front Load Washer

1 Answer

Hotpoint WMA13 door lock fault


If the door locked light is flashing , then the main board probably has a fault on it, due to a problem with the motor, or the board itself being faulty.
Recommend calling an engineer.

Oct 15, 2008 | Hotpoint WMA13 Front Load Washer

2 Answers

Door Lock light Flashing


IF this is the A WMA model then im affraid to say that you have blown your program board.. This depending on the extent on the damage can be repaired but 7 times out of 10 it usually is not...

if you was to remove the front pannel by unscrewing the screws around the soap draw section... and remove the panel.... then detach the board from panel you will c where the largest plug is connected to the board that its is blown.....

P..S Removing the top cover makes removing the front panel a lot easier... The screws are near the front on the sides....behind the little clips

Nov 12, 2007 | Hotpoint WMA35 Front Load Washer

Not finding what you are looking for?
Hotpoint WMA35 Front Load Washer Logo

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...