Question about Hanns.G Corporation JW-199DPB 19" LCD Monitor

1 Answer

Monitor i'm new at computer...I don't know what I've done but the monitor is like in a state of zoom! Awful...I tried to come back at the original view status but the menu says osd locked...how can I put my monitor back?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,940 Answers

Here is a link to the Monitor manual

http://america.hannsg.net/filectrl/JW199D_UM_EN.pdf

Most OSD's lock/unlock by pressing the menu button and holding it for 15 seconds

Posted on Jun 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 40" screen colby flat screen, I'm having problems with my monitor coming back on???? I've tried leaving it unplugged for two days but when I plug the monitor up, don't nothing com


if the power indicator goes light green then turn to red, you must check the power supply board. look for a bulging capacitors.http://en.wikipedia.org/wiki/Capacitor_plague.a panasonic brand capacitors with low esr is a good replacement just look for the ratings and value must be the same when replacing. then make it sure check the polarity the positive and the negative. just let me know if you need further assistance good luck

Nov 01, 2012 | Computer Monitors

1 Answer

My monitor is flickering


Flickering on the screen can be caused by defective hardware in the computer or by improperly installed software monitor may flicker and goes into rolling state due to dust, overheating after a long continuous usage,loose circuitry or due to some electromagnetic interference with other like tv , UPS, large speaker systems etc.


FIX :

1.Try Re-installing your Video driver

2 If it is possible, connect a different monitor to the computer. If the flickering disappears, it is a fair indication that the monitor is defective, otherwise go to the next step.

3. Set up the computer and the monitor on a different place in your house. If the flickering disappears now, it is most likely an interference caused by something in the original location. Check for devices which can cause interference.

4. If the flickering persists, check the setup of your system. If available in the setup, make sure that the option Monitor Type is configured as Colour Non-Interlaced.


If you don't think any above possible reasons for the rolling or flickering state of your monitor then we recommend you to get your monitor checked by the monitor company at their respective service cente

Sep 01, 2011 | LG Studioworks 700S 17" CRT Monitor

1 Answer

The monitor worked fine until recently. It requires turning off and back on, to view for about 2 seconds, before back off. Checked with other PC - same problem.


This behavior is often caused by bad electrolytic capacitors on the circuit board inside. It's not difficult to replace them, but requires skill with electronic soldering and access to the replacement parts. This site as well as some others has information showing what needs to be done, and detailing the parts to be replaced.

If you know someone who can solder, give it a try. There are many online parts sources, and if you live near a Radio Shack store, you might be able to find the replacement capacitors there. A capacitor's value is measured in microfarads, usually abbreviated as MF. There is also a voltage rating. The original parts are rated at 16 volts; if 25- or 35-volt rated ones of the same value are available, use those. They will be a little larger than the originals, but will last longer.

Good luck with the repair, and thanks for using Fixya!

Oct 17, 2010 | Dell UltraSharp 1702FP 17" Flat Panel LCD...

1 Answer

My Starlogic monitor fails to power up. We had a recent power outage. Everything else on the computer seems to work properly however when I power up the pc the monitor will not turn on. Have manually...


Not sure if you have done this so give this a try.

* If possible, plug your Starlogic monitor into another working computer. If the Starlogic monitor works then it is the port on the original computer that has gone bad. The solution would be purchasing a new video card such as PCI or AGP video card. (Assuming all other aspects of your PC are working fine)
*However, if the monitor does not work then you know your monitor is dead. You will need to buy a new or used monitor. **You may want to barrow someone's monitor and test your original computer just to make sure the port on that original computer is fine.

Jun 16, 2010 | Star Logic 17" LCD Monitor

1 Answer

The monitor is giving a zoomed in view . its not giving the full view of the desktop screen rather a section of it is zoomed in . there are no settings to zoom out .??


ur setting may be set to low resolution...
try doing this
go to Desktop/right click/properties/Settings/Screen Resolution/
What do u c...what's the resolution there...800x600...
if the slider(pointer) is active use it to increase it to say 1024x768, 1152x864, 1280x1024 etc.
use the correct resolution....as too much of resolution will make ur monitor un-viewable...
also try if ur monitor has some press button on them to make changes to the correct setting/zooming of the screen image...

Dec 24, 2009 | Samsung Syncmaster 2033SW Monitor

1 Answer

Problem with powering the monitor up. It just flicks off.


The operating system would not stop it from powering on.
It should power on even if disconnected from a computer.
You are probably in need of having the powerboard redone. Possibly a failing inverter.
If you know how to take it apart and can get some pictures to me at bammbamm@ptd.net , I may be able to see the problem.

Jun 20, 2009 | Samsung T220HD LCD Monitor

1 Answer

The view window is cut off (by approx. 10%) at top and bottom of monitor screen. How can I fill out entire screen? Thanks


on the monitor there are buttons normally with menu two other and a select button try going into the menu to size and position in there there should be a zoom selection try adjusting the zoom it should help

May 04, 2009 | Computer Monitors

3 Answers

Thin line across computer screen


Your Display cable (inside your monitor) needs to be replaced.

I would look on ebay to try and find the part and then take it to a local tech to replace it for you as I would not recommend anyone take apart a monitor (LCD OR CRT) if you had never done so before.

OR, Buy a new monitor.

Mar 08, 2008 | Gateway FPD1975W 19" LCD Monitor

Not finding what you are looking for?
Hanns.G Corporation JW-199DPB 19" LCD Monitor Logo

Related Topics:

558 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hanns.G Corporation Computer Monitors Experts

Matthew Spark
Matthew Spark

Level 3 Expert

1042 Answers

 Grubhead
Grubhead

Level 3 Expert

4593 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Are you a Hanns.G Corporation Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...