Question about Dewalt DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver

1 Answer

Cannot remove drill from chuck - Dewalt DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 178 Answers

Remove the REVERSE-THREAD screw at the bottom of the chuck. Set the clutch collar to the highest setting, and set the gear to the slowest setting on the transmission. Remove the power source! Get the biggest allen wrench you can fit in the end of the chuck(the shortest leg) and tighten the chuck down around it, allowing the jaws to rest and tighten on the flats of the wrench. Lay the drill on its side(chuck toward you, handle to the left, and allen wrench to the left, horizontal to the deck. Then with a hammer(soft hammer if you care about the allen wrench) quickly and deliberately hit the allen wrench in an attempt to cause the allen wrench to spin counter clockwise. Let me know if this works for you!

Posted on Nov 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove a drill chuck from an Hitachi corded drill


How to Remove Drill Chuck
If there is screw in inside center of chuck remove it, it is probably left hand threads so pretend you are tightening it and it will come free. open chuck fully and insert chuck key into holes and hit it with a hammer to remove it.

Oct 07, 2017 | Hitachi Drills

1 Answer

My new bosch cordless drill chuck doesn,t have a screw in it how do i remove the chuck ?


Dear Fred,

Please go to Replacement Parts in the link provided below. Too replace and remove your drill chuck on a cordless drill.

How to Remove Drill Chuck

Fare Well

Feb 07, 2015 | Bosch 13618 - 2G 18V Brute Tough Cordless...

3 Answers

How to change the chuck on 18 volt cordless drills


Set the drill to reverse. Hold the chuck, press the trigger and open the drills chuck to it wide open position. Now,, take the correct size allen wrench and insert it into the back of the chuck to remove the screw. Turn the screw clockwise to remove it. Notice I said clockwise, just the opposite of what you might think. Hold the chuck with your hand or a pair of large vise grips and press the trigger to unscrew the chuck from the drill. Rotate it counterclockwise to remove it from the drill. Reverse the procedure to install the new chuck.

Mar 10, 2011 | Dewalt 18 Volt Compact Drill Kit

1 Answer

How do you remove the chuck of 18 volt cordless drill?


lock an allen key in chuck,,chuck has l/h thread so turn chuck anticlockwise to remove

Jul 07, 2010 | Craftsman 19.2V C3 DRILL/DRIVER

1 Answer

Drill chuck removal


Look down into the chuck and you will see a screw. It must be removed so that the chuck can be pried off. It should be righthand(standard thread) lefty loosey. An impact driver is my favorite tool for removeing the screw, as you must not strip it or you will have to drill it out. Once the screw is removed, put the drill in a padded vise if one is available and do what is necessary to pop the chuck off. Something with enough width to span from the chuck to the drill body can be carefully driven between the two to break it loose.

Apr 04, 2010 | Dewalt 3/8" Electric Drill D21009

1 Answer

I have a 12v makita drill and cannot remove the chuck i have removed the screw inside the chuck. lease help


The chucks on most drills are left hand thread. To be sure which way to turn the chuck check the screw the chuck will turn in the opposite direction.

Mar 29, 2010 | Makita 12 Volt Cordless Drill/Driver Kit

1 Answer

How i remove a dewalt drill chuck Model dc988


put the drill in speed setting 1 before you continue~!

Step 1. This step loosens the screw inside the chuck. Open the chuck all the way — if you see a screw inside, it’ll need to come out before you can remove the chuck. If there’s no screw inside, you can skip steps one and two.

Step 2. If there’s a screw inside the chuck, typically the threading will be left-handed, so turn it clockwise to remove it. Be careful, and use the right size screwdriver — you don’t want to strip the screw.
step-2.gif Step 3. Insert the largest hex key that you have into the chuck, short-side-in, and tighten the chuck. Tap the hex key sharply in a counterclockwise direction to loosen the chuck. Now you can remove it by hand.
step-3.gif This won’t work for every consumer drill ever made, but pretty close. Most drills will match one of two common chuck-threading standards: 3/8′-24 threaded mount for 3/8′-capacity drill chucks, and 1/2′-20 threaded mount for 1/2′-capacity drill chucks — but on some drills just the opposite may occur. To be safe, always check the thread count before you buy a replacement drill chuck.

Oct 07, 2009 | Dewalt DC988VA XRP 3 - speed 1/2" 18v...

2 Answers

Can't remove the chuck on a drill.


There are one-way (non-reversible) and two-way (reversible) drills. Mine is one-way. Methods for chuck removal are different for these two types.
Procedure for one-way (non-reversible) drills:
Drills of this type have no chuck screw, so one have to hold the spindle with a wrench, than to sharply strike the wrench with a hammer to spin it off.
Procedure for two-way (reversible) drills:
Open the chuck up and in the bottom is a screw that holds the chuck on the shaft.The screw turns in a clock wise motion to be removed and then you can top the chuck off the shaft.

May 19, 2009 | Black & Decker Drills

2 Answers

I need to remove the chuck from the drill


In continuation after removing the chuck screw which is left hand thread shift the drill to LOW and use a bent handle allen wrench approx the size of the chuck lock it in the jaws. Turn clutch setting to the drill only position and using a hammer strike the hex key. The chuck has standard threads. To reassemble just reverse this

Nov 17, 2008 | Makita 6019DWE 3/8 Cordless Drill Keyless...

Not finding what you are looking for?
Dewalt DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver Logo

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Drills Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Lance Guthrie
Lance Guthrie

Level 1 Expert

18 Answers

Spud Howell

Level 2 Expert

66 Answers

Are you a Dewalt Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...