Question about Mitsubishi WD-52525 52" Rear Projection HDTV

3 Answers

Mitsubishi HD 1080 wont turn on now

This TV is just at 5 years old and has worked great with no problems until out of the blue it has no power and will not turn on. Thanks for any help.
Ken tv will not turn on power light continues to flash. Tried hard reset, no luck.
Tried the reset on the front of the tv, no luck. Checked the fuse in the back, it is good. Now what? I would like to watch it, but it will not turn on.
Thank you I hope you can help.
Sincerly
Susie Valle

Posted by on

  • lesset Jun 08, 2008

    Thanks for your help, but I got it to turn on.
    I pushed the reset a bunch of times, the light continued to flash then went off. It worked to my surprise. At least it is working for now. I hope it lasts. This has been happpening for a couple of months. This being the longest time off.
    Thanks agian
    Susie

  • lesset Jun 08, 2008

    I checked the fuse, it was good. I used to be a digitronics tech so touching was not an issue. Thanks for you info. It is working after pushing the reset numerous times.

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 983 Answers

Have a check with the transformer ...
there may be any miscontact in transformer ...

Posted on Jun 07, 2008

  • Dileep Keshavanarayana
    Dileep Keshavanarayana Jun 07, 2008

    some capacitor might have gone or it is getting heated too much ... so may be due to excess temperature of the transformer or the capacitor it is not working ..
    have a check with this .............


×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 13,433 Answers

This document may be usefull
http://www.jeremyburns.com/Mitsubishi-Green-Blinking-Light-Fix.pdf

heres a picture of bad capasitors
http://www.auctioncreations.com/wd62525a.JPG


This text was written by another expert on this site, CTF1800:

Here's something that might also be useful. After you turn on the set, and get the regular red blinky lights, hold down the Device and Menu buttons together for about 5 seconds.
The Power light will start to flash in a two digit sequence.

For example, 3 flashes, then 7 flashes = 37.


Here are the error codes, and the corresponding problem:

12 = No error detected, check power supply.
32 = Lamp Cover is open.
33 = Air filter cover is open.
34 = Lamp abnormality
36 = Light Engine (DMD or Lamp Fan stopped)
37 = Exhaust or Lamp Ballast Fan stopped
38 = Lamp Temperature High
39 = DMD Temperature High
41 = Short is detected
44 = DVI cable between FMT and Engine disconnected

Posted on Jun 07, 2008

  • Ekse Jun 08, 2008

    I'm not sure is the problem solved completely but if you are satifyed you may press the accept button on the solution of your choice.

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 198 Answers

Did u by any chance open the assembly of the tv and touched the pcb board... the circuits on this board r very delicate and u shud be very if u r handling tis....

wen u switch on ur tv r u able to listen to any sound or wat?
if yes reply back, i wil help u

Posted on Jun 07, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My LG turns off in the middle of a prgram then i hear 3 clicks intervals until i turn off at power point as remote wont do it. Only started doing it this week . TV not old & never had problem before .


The main power supply regulator section circuit fault. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.
Search the site by type in the "brand name" to your device; in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

Jan 11, 2017 | LG Televison & Video

1 Answer

EMERSON 55 INCH TV MODEL: LF551EM5 SERIAL: DS2A1433113216


Sounds like The main power supply regulator section circuit fault. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/
It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.

Jan 10, 2017 | Emerson Televison & Video

1 Answer

I have pioneer plasma tv about 6 years old. I turned the power on, sound but no picture. Do you think it is worth fixing?


no
plasma tv units consume considerable power and the latest led units don't so for the extra cost of a new unit , there will be a power saving over the years

Jan 08, 2017 | Pioneer Televison & Video

1 Answer

Problem I can't intall my product many times its turn off itself all my installation are well install with my blu-ray ARC tv to ARC Blu-ray are well install I don't understand why its turn off itself


The blue ray turns off or the TV? and what models?
ELECTREPAIRUSA@ELECTREPAIRUSA or you can contact us at that address as we repair/renovate all items electronic and electrical old and new.

Jan 07, 2017 | Televison & Video

1 Answer

To begin with I have Dish network my TV went off and since then in order to have picture and sound i have hookup HDMI cable and also video cable to have picture and sound


You need to set up the dish box for the correct resolution ie 720/1080 etc.
ELECTREPAIRUSA@ELECTREPAIRUSA or you can contact us at that address as we repair/renovate all items electronic and electrical old and new.

Jan 05, 2017 | DISH Network Televison & Video

1 Answer

How do i fix my elonex tv


switch off.wait for 5 mins.
press & hold power button till it turns on then off.
ifno luck try this-
switch on by pressing power button while holding volume + and -.
keep hold of both until powers on.
can take few mins.
good luck!!!

May 04, 2014 | Televison & Video

1 Answer

Would like to know the codes for a LG tv, Sony tv, and a TOSHIBA DVD ?


How to Program


Remotes With SET Button
1. Choose and press a device key i.e TV. LED will flash once.
2. Press "SET" Hold until the LED Lights up.
3. Enter the 4-digit Device code (refer code list).
4. The LED will flash once as each number is programmed at the end of the 4 digit the LED will turn off immediately if correct. If the LED flashes then something went wrong in the process. If the first code does not work then repeat the process with the next.
5. Important - Some brands use other manufacturers to make their devices if the codes available do not work the try the MAGIC search function.


Remotes Without SET Button
1. Choose and press a device key i.e TV. LED will flash once.
2. Press and hold BOTH the CHANNEL UP AND VOLUME DOWN button until the LED Lights up.
3. Enter the 4-digit Device code (refer code list).
4. The LED will flash once as each number is programmed, at the end of the 4th digit the LED will turn off immediately if correct. If the LED flashes then something went wrong in the process. If the first code does not work then repeat the process with the next.
5. Important - Some brands use other manufacturers to make their devices if the codes available do not work the try the MAGIC search function.


MAGIC SEARCH FUNCTION
1. The magic search function enables you to scroll through the entire code list one by one by pushing the on/off button. Each time you push the on/off button the remote automatically switches to the next code in the list and sends a signal to the device you have chosen.
2. Choose and press a device key i.e TV. LED will flash once.
3. Press and hold the SET button or if no SET button then hold BOTH the CHANNEL UP AND VOLUME DOWN button until the LED Lights up.
4. Enter the 4-digit Device code (refer MAGIC list) i.e TV is 0001.
5. The LED will flash once as each number is programmed at the end of the 4 digit the LED will turn off immediately if correct. If the LED flashes then something went wrong in the process.
6. Start scrolling by pushing the ON/OFF button as soon as your TV or Chosen device turns OFF lock the code in by pushing the DEVICE key again.

Mar 27, 2013 | Televison & Video

33 Answers

TV just flashes different colors


You have entered a diagnostic colour test. With the TV powered on, hold the 'Menu' & 'Enter' together, then press the power button. Problem resolved

Jun 25, 2006 | ViewSonic N2750w 27 in. HD-Ready LCD...

Not finding what you are looking for?
Mitsubishi WD-52525 52" Rear Projection HDTV Logo

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1198 Answers

The Knight
The Knight

Level 3 Expert

69878 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...