Question about Xerox Phaser 7400DN Laser Printer

Open Question

Error code fault 917 - Xerox Phaser 7400DN Laser Printer

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error 917


917 Error in the Transfer Unit Belt. The Belt Rotation Sensor indicates an error.

Code 917: The Transfer Belt Rotation Sensor indicates a belt error.
Initial Actions:
? Check the condition of the Transfer Unit drive gear.
? Cycle the printer's power.
? If the problem persists follow the procedure below.

Troubleshooting Procedure Table
1 Test the Belt Rotation Sensor.
Run the Service Diagnostics Belt Hole IC test.
Does the sensor function correctly?
Yes) Go to Step 2.
No)Replace the sensor. If the error persists, go to Step 3.
2 Test the Transfer Unit Motor.
a. Close the Interlock Switches for test.
b. Run the Service Diagnostics Transfer
Belt Motor test.
Does the motor operate?
Yes)Replace the Transfer Unit. If the error persists, go to Step 3.
No)Replace the motor. If the error persists, go to Step 3.
3 Check all pins on the HALL1 Harness for continuity.
Disconnect HALL1 and P/J310
Is the harness conductive?
Yes)Replace the Motor Driver Board.If the error persists, go to Step 4.
No)Replace the HALL1 Harness.
4 Check all pins of the DRV0 harness for continuity.
Disconnect the DRV0 ribbon cable.
Is the cable conductive?
Yes)Replace the Engine Control Board.
No)Replace the DRV0 Harness.

Aug 18, 2011 | Xerox Phaser 7400/DT Laser Printer

2 Answers

What state in usa is area code 917?


Hi,

Area code 917 is a New York City telephone area code for all of the five boroughs (Brooklyn, Manhattan, Queens, Staten Island, and the Bronx).

Regards,
Shrey

Jun 07, 2011 | Computers & Internet

1 Answer

Getter "Report fault 917" on my Phaser 7400. How can I fix?


I am getting a report fault 917 error on the phaser 7400

Sep 23, 2010 | Xerox Phaser 7400/DXF Laser Printer

1 Answer

Error message 917.00 service transfer roller. I replacedn the service roller but still the error message comes up.This is from the IBM Infoprint 1552.


A 917 transfer roll error code on all models at service level may
display if an incorrect level HVPS is installed in a printer that has the erase lamp assembly installed.
Check to make sure the correct level HVPS is installed.

Feb 11, 2010 | Office Equipment & Supplies

1 Answer

Print error 917


That is a fault in the transfer belt hole sensor. It is a sensor used to know the proper position of the belt seam. I would suspect it is covered with toner, the belt has tracked to the front or back, the belt is slipping, or the belt is damaged.
I would think replacing the transfer belt would resolve the problem It is called the belt hole IC in diagnostics.

Jan 20, 2010 | Xerox Phaser 7400DN Laser Printer

2 Answers

I have a oki 9600 Fatal error 917


Replace the transfer belt unit. A 917 is a belt **** sensor error.

Jun 19, 2009 | OKI C5150n Led Printer

2 Answers

Lexmark t644 error code 917.00


This error indicates that there is a charging problem with the transfer roller. You could start by cleaning the contacts for the transfer roller (power off printer first). The transfer roller is the black foam-like roller under the toner cartridge. Handle it with paper because the oils on your hand could damage it. To remove it, just pry under the far left side with a screwdriver. Lift and pull to the left to remove. If this does not fix it, then you have a more serious problem. It could be one of the arms or the HVPS.

May 07, 2009 | Lexmark T642 Laser Printer

3 Answers

Fatal error 917 on an Oki C9600 printer. What does this mean and how can I resolve the problem. Many thanks James


A fatal error 917 means there is a problem regarding the belt **** sensor.

Usually it means the printer can't see the transfer belt rotating.

First thing to try is to remove and re install the transfer belt, if that does not work you should replace the transfer belt.

Jan 07, 2009 | OKI C9600hdn Laser Printer

4 Answers

Power Off/On Fatal Error : 917


The 917 fatal error is a belt **** se sensor error. This could be caused by the belt not installed correctly or the belt at the end of its life, or the belt being torn. Please power the printer off and then reseat the transfer belt and then power the printer back on. If the error remains then I will need you to check the life remaining on the transfer belt. Also make sure the transfer belt is not torn.

Aug 08, 2008 | Xante Ilumina Digital Color Press Printer

Not finding what you are looking for?
Xerox Phaser 7400DN Laser Printer Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Philip Hughes

Level 2 Expert

80 Answers

docukaaf

Level 1 Expert

38 Answers

Are you a Xerox Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...