Question about PC Desktops

1 Answer

Emachine t1115 will not accept new memory - PC Desktops

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

Chances are you have more than it supports, chip to fast or slow, or bad chip. Go to crucial.com and run the memory scanner and make sure you have the correct speed and size.

Posted on Jun 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want upgrade my emachines t6528 hard drive and ram.i need help


Memory Upgrade for eMachines eMachines T6528 Computer, the eMachines eMachines T6528 Computer takes the PC3200 DDR SDRAM DIMMs. Supports Dual Channel DDR. Memory Type, and comes installed with 512 MB (removable) of Memory. You can upgrade your eMachines eMachines T6528 Computer to up to a maximum of 4.0 GB Memory, the system has 4 sockets to install Memory, already with 512 MB (removable) standard Memory installed. For best Computer performance use the maximum amount of allowed Memory per slot for your Computer.


As for the Hard Disc.... the following address will give step by step instructions on installing a new HD. http://www.manualowl.com/m/eMachines/T6528/Manual/

Thank You for using FixYa
Tom Miller
KD4DTK

Aug 19, 2012 | E-Machines T6528 PC Desktop

1 Answer

Our emachines el1200-06w runs very slow after sitting idle for any length of time - when we start it up, it runs OK, but later it almost stops - takes very long time to process. we run defender pro 2011...


You need to upgrade your memory to the maximum allowed by your motherboard which in your model is expandle to 4gb of ram max. You should be fine with the cpu that you have, just don't be running high gaming, digital editing, programs. You shouldn't multi task that much either too, because your cpu isn't meant to handle that much of a thread. But adding memory will solve the slow unresponsive promblem you are dealing with. Your computer should accept ddr2 memories. Remember don't go over 4gb, otherwise your computer won't function correctly.

Jan 30, 2011 | E-Machines eMachines Desktop PC

1 Answer

Just installed 2 2GB cards (Corsair VS2GB800D2) to replace the 1 1GB card in my emachines EL1200 series. Computer will not boot. replaced the old card and it booted right up.


Will it boot with only ONE of the 2GB memory-sticks installed?
Will it boot with ONE of the 2GB memory-sticks AND one of the 1GB memory-sticks?

Look closely at the 1GB memory-sticks.
Does the label show 'DDR266' or 'DDR333' or 'DDR400' or 'PC2100' or 'PC2700' or 'PC3200' ?
Do the 2GB memory-sticks have _identical_ information?
It's definitely _not_ acceptable to have "slower" RAM (smaller numbers) in the new RAM,
but it _might_ be acceptable to have "faster" RAM (larger numbers).

Nov 12, 2010 | E-Machines eMachines Desktop PC

1 Answer

I have an emachine T5026. Emachine tech swears this machine only supports pc2700 ram but the stickers on the factory installed ram says pc3200 256mb x 2 so i bought 2 memory masters pc3200 1gb x 2 sticks....


PC3200 is backwards compatible with PC2700. Meaning you can install PC3200 into your motherboard but it won't run any faster than would PC2700, however it will not cause any harm and should work fine.

Emachine's would say you need PC2700 most likely because they're trying to sell you some.

One of your new memory modules or the memory slots on your computer may be defective. I recommend installing a single stick of memory and booting your system. If it is successful then shut it down, disconnect the power and install another stick. Boot again and keep doing so and by process of elimination identify the bad memory stick or the bad memory slot.

This is the "likely" cause and isn't too uncommon.

Good luck.

Sep 07, 2010 | E-Machines eMachines Desktop PC

1 Answer

Installing a 512mb PC133 memory module in a t1090 emachine. The pc wont recognize the module and wont boot nor go into post. Switching back to the original two 128mb modules and the pc works normal. Is...


Hi there
Your t1090 will only accept a maximum chip size of 256Mb and so it will not accept the added the 512mb chip as it cannot handle it. 512 is the maximum size of RAM for this machine but unfortunately you cant put it in in one go

Jul 03, 2010 | E-Machines T1090 PC Desktop

1 Answer

Dual Channel on an Emachines T5082


Look closely at the BOLD print

Memory Upgrade for eMachines eMachines T5082 Computer, the eMachines eMachines T5082 Computer takes the PC2-4200 DDR2 SDRAM DIMMs. Supports Dual Channel DDR2. Memory Type, and comes installed with 512 MB (removable) of Memory. You can upgrade your eMachines eMachines T5082 Computer to up to a maximum of 2.0 GB Memory, the system has 2 sockets to install Memory, already with 512 MB (removable) standard Memory installed. For best Computer performance use the maximum amount of allowed Memory per slot for your Computer.
Choose the following Memory Upgrade for eMachines eMachines T5082 Computer.

Apr 17, 2009 | E-Machines T5082 PC Desktop

2 Answers

Emachine t5206 adding 2 gig of memory


How much memory are you trying to add?

Nov 08, 2008 | E-Machines eMachines Desktop PC

Not finding what you are looking for?
PC Desktops Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top PC Desktops Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Are you a PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...