Question about Kenwood Car Audio & Video

1 Answer

My kenwood KDC 8021 head unit, LCD display is not turning on. i have reset the unit and removed the rear cable and reconnected it still nothing. when the unit is turned on the screen briefly flashs, but thats it

Posted by on

1 Answer

Code

Posted on Sep 18, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, i can not figure out how to get past or reset the protect mode on my kenwood kdc mp 142


The model that you refer to has the reset button just before the 1 Button. Press that for a second with a pen or something of the the same point size and there is no need for force. This will reset the head unit. All personal settings are lost when reseting the unit. However if it goes into protect again then there could be a mistake in the installation somewhere, most likely incorrect speaker installation or speaker cable shorting on metal somewhere. There could be other reason but these would be most likely the cause. Good luck dreamsystems

Feb 08, 2011 | Car Audio & Video

1 Answer

KDC-4051UG Only comes "ON" with


Your head unit is now connected correctly. That is how it is intended to be installed. Unless it doesn't store the radio stations. In that case the power cables of the head unit (RED&YELLOW) are incorrectly connected, but not a big problem. hope that helps dreamsystems

Feb 06, 2011 | Kenwood Car Audio & Video

1 Answer

I have a Kenwood KDC-322 car radio. It says enter code. Does anyone know where i can go to get this code?


The only way that i know how to get the stereo to unlock is to remove the power from the stereo for about 10-15 seconds then reconnect power back to stereo this should reset the unit.

Jul 24, 2010 | Kenwood Car Audio & Video

1 Answer

Question on the back ports on head unit


Hello BCRich356,

The USB input to the KDC-X993 is a cable hardwired into the back of the unit. To extend the length of the cable, you would need an extension with a male connector (like on the thumb drive itself) on one end and a female connector (like the thumb drive plugs into) on the other end.

There is no port on the back, it's hardwired. Just like the AUX cable.

Hope this helps.

May 05, 2009 | Car Audio & Video

1 Answer

2 problems, what are the red and yellow wires on a Kenwood kdc-mp2028? and can you install a used kenwood without the remote?


You can use the head unit with no remote - that's just an accessory. As for the wires, the red is switched power (this gets wired in so that it only has power when the key is on - when the key is off, it turns off the radio). The yellow is constant 12v power (to maintain power to the head unit so that memory settings, treble/bass settings, and the clock are maintained when the vehicle is shut off).

Sep 24, 2008 | Kenwood Car Audio & Video

1 Answer

I just bought a KDC MP-235 to put in a 95 camaro with bose amplified speakers. I ordered a amplifier intergration component to reduce the output of the 50 watt per channel head unit as to have better...


Hi,

Yes, the Kenwood KDC MP-235 has two (2) line level outputs (RCA types red & white). However, these outputs internally passed through an electronic crossover/filter making them appropriate for subwoofer amps only.

If your unit is an MP-235CR, then the same outputs would be for the rear amp (not subs) and are full range (unfiltered).

If indeed your unit is an MP-235 and if I may make a suggestion, still connect the Kenwood to four (4) speakers. It would not be technically correct to leave the internal amps operating with no load (speakers) connected. Additionally, you would be getting 200 watts (4 X 50) more to your system (since it is already there).

If your Bose amp & speaker are subs, then no issue, however if the Bose is for a full range of speakers, then only the woofer part would be working efficiently.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

May 15, 2008 | Kenwood Car Audio & Video

8 Answers

Kenwood car stereo KDC-W3534 : warning message PROTECT


i had the same problem and i just disconnect the battery and and reconnect it and everything works fine!! try it

Dec 19, 2007 | Kenwood KSC-310CCS Center Channel Speaker...

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4724 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...