Question about Audio Players & Recorders

Open Question

Panasonic remote control n2qagb000004

Hi. I have a panasonic SCAK44 shelf sound system. My problem is with the remote control n2qagb000004. All the buttons work fine except the on/off stanby button. This no longer works and I have to turn the system on and off manually.

Can anyone please help me fix this problem.

Many thanks

Posted by on

5 Suggested Answers

  • 3 Answers

SOURCE: volume/ channel/ remote not working

I just used the following instructions from this site on my 'totally dead' Ilo remote and it worked like a charm! I did step 2 twice on each key and put the batteries back in and it worked great! Hope this helps you too. "Dead" Remotes Can Be Saved How to Re-Start Your "Dead" Remote Control This only takes about a minute and will restart 1 in 3 "Dead" Original Remote Controls. Good Luck! Step 1- Pull the batteries out of the remote and leave them out until Step 4. Step 2- Press and release each and every button one at a time on the remote control until every button has been pressed and released at least once! Step 3- If your remote has slide switches, you must move the switch to each position then repeat the button pushing in Step 2. (When you're done, be sure to put the slide switch in the correct position to operate the unit the remote came with!) Step 4- Put the batteries back into the remote, being very careful to install them correctly. New batteries should be used if you're not sure about the old ones. Step 5- Try the remote. If it works, Great! If not, it's time to call 1-800-Remotes or use this website to order a new remote.

Posted on Jan 23, 2007

  • 1 Answer

SOURCE: Panasonic NN 9850 wall micro/convection oven

PLEASE CHANGE MEMBRANE SWITCH

Posted on Oct 05, 2007

SOURCE: cd tray

Tienes que abrir el aparato y cambiar la banda de impulsion de la bandeja y darle mantenimiento al mecanismo del cd.

Posted on Mar 29, 2008

  • 1 Answer

SOURCE: F61 error

whats wrong is that whilst the power amplifier is running and the system fan fails due to internal resistance of the fans resistor the main power amplifier overheats causing the main power NPN transistors to turn off the system power by the use of a logic AND gate that causes the error code F61 to appear and turn off the systems power supply. The solution is simple the main transistors are removed carefully and their terminals are shorted using a screw driver. the transistors contains a little voltage which activates the AND gate to shut off the power supply and the error F61 appears. make sure the transistors are replaced correctly and solder very light. If the problem still occurs provided that all transistors are fully shorted(all three terminals) and properly replaced then the radio should be taken to a professional

Posted on May 23, 2008

  • 2 Answers

SOURCE: Panasonic TH-50PX60U no buttons working

The software in the cpu of this set is damaged you must reload it to fix the problem..

Posted on Dec 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I have a Panasonic SA-PM200 mini hifi how do tune the radio stations


Make sure that you have the source set to FM or AM and the correct sound quality mode selected. Then press the Search track (fast forward or fast reverse) buttons on the remote. (These two buttons have the << or >> symbols and are on either side of the Stop button on the original remote.) If you press and hold the button, the radio will scan the frequencies in that direct until the next station that can be tuned in. The Skip buttons ('<< or >>') only goes to preset stations. As far as I can tell, these buttons are not on the main unit.

The remote is listed as part N2QAYB000639 . A replacement remote is available at several online locations including amazon.co.uk . See https://www.amazon.co.uk/Panasonic-N2QAYB000639-Remote-Control-SCHC15EBK/dp/B00H988QAM . The manual is available online here: http://panasonic.ae/en/manuals/SC-PM200.pdf . The SC-PM200 is the model for the entire system; SA-PM200 is the main unit. See section 7 for the radio tuning information.

I hope this helps.

Cindy Wells

Oct 28, 2016 | Panasonic Audio Players & Recorders

1 Answer

MY SYSTEM WILL NOT TURN ON EVEN WHEN I PUSH THE POWER BUTTONur problem?


my remote control don't work I thank it's the remote control signal sensor.

Nov 07, 2011 | Panasonic SC-AK100 CD Shelf System

1 Answer

I HAVE AN OLD SA-SK600 CD PLAYER WITH 5 CD CHANGER AND 5 SPEAKRS I LOST THE REMOTE CONTROL FOR THIS SYSTEM HOW CAN LET THE OTHER SMALL SPEAKERS WORKS UNTIL I FIND OTHER REMOTE CONTROL


the only way is to use dolby pro logic mode but you can not set the volume of centre and surround speakers individually now,for that you need a remote.

Dec 13, 2010 | Panasonic SC-AK600 CD Shelf System

1 Answer

Hi guys iv been look for a remote control for my technics sc dv170 can any body help please


u can go to this website (official panasonic/technics) https://www.pas-europe.com/ just input the old remote control number which is on the front of the remote or if u dont know it input the model number of the system as in your case its SCEH790. i ordered a remote control from here and i received it 3 days later. i have the same system so the remote will be the same the remote code it EUR7702270 so just put that in the bar BUT WHEN YOU RECEIVE YOUR NEW REMOTE IT WILL HAVE A DIFFERENT CODE ON THE FROM LIKE MINE DID AND THE NEW CODE WILL BE EUR7702050. hope i have helped and hope i have saved you the worry of it not working if you do buy from panasonic. the cost of the remote is £19.07 but with the VAT and shipping it costs £22.13.

Nov 05, 2009 | Technics SCEH790 CD Shelf System

1 Answer

I lost my remote control to my panasonic SA-AK17.Where can i buy?


yes you can. i used a 3 dollar universal remot i got from the dollar genral here in new york. works great.

Oct 02, 2009 | Panasonic SC-AK17 Shelf System

1 Answer

Need remote control code for Panasonc sa-pm01 (stero system) for programming into a TV/universal remote


This is the best i can do mate hope it helps:
http://www2.panasonic.com/consumer-electronics/support/Audio/Home-Theater/Micro-Systems/How-To-Guides/model.SC-PM01.H#ts

Aug 09, 2009 | Panasonic Audio Players & Recorders

1 Answer

Panasonic cd stereo system sa-ak100


my remote control don't work. I thank it's the remote control signal sensor. what should I do.

Jun 20, 2009 | Panasonic SC-AK100 CD Shelf System

1 Answer

Can't play iPod on my panasonic sa-en27 with out a remote


I ran into the same issue, instead of buying a replacement remote I was able to dial in a Vip 211 dish network remote control with remote code 643 in AUX setting. Then once the code was in, i pressed the 6 key on the remote and now I can listen to audio on the music port. The 643 code refers to the first Panasonic amplifier/receiver in the code list. To further clarify, I pressed AUX for 4 seconds, pressed 2 to signal I am programming an amplifier/receiver device, then punched in 643 then pound sign.
Good luck with yours.

Feb 14, 2009 | Panasonic (SCEN25) Shelf System

1 Answer

Sound


hi, ya, someimes the POT i.e the volume controller variable resistor loses its contacts with the carbon strip. tru using some switch cleaning solution( NoN Acidic) to clean the POT,let me know

Dec 07, 2006 | Yamaha GX-70 CD Shelf System

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio Players & Recorders Experts

kakima

Level 3 Expert

102366 Answers

 Grubhead
Grubhead

Level 3 Expert

4861 Answers

The Knight
The Knight

Level 3 Expert

72640 Answers

Are you an Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...