Question about Panasonic SC-HT75 System

2 Answers

Dvd problem cant get dvd out of unit. unit flashes "change". all lites for dvd carousel flashing.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have just done the same thing... All you need to do is open the unit, 3 screws on back and 2 on each side.

You will need to open the DVD drawer half way and then use something to tease out the disc. I used a bamboo scewer as it let me reach into the drive and place the through the hole in the middle of the disc and push it out over the drawer.

Posted on Dec 14, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 682 Answers

Try to reset the system disconnect the system from power and re connect it again.

Posted on Jul 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Philips HTS5550 home theater. The dvd machine has of late been displaying a "No disc error" when i insert a dvd in the machine to play. I have already tried using the cleaning kit. What might


if there's no flashing red light on lens?.. the ribbon connector of lens is not properly connect, or change it if you notice that it has lines cracked. the bad performance of the disk spinning motor is also causing why was your unit displaying "no disc" error.

Aug 04, 2014 | Philips HTS5550/12 DVD/DivX Home Cinema...

3 Answers

Dvd problem


Hello colt86,
Does the DVD plate domes out? Is it stuckde?

Jun 06, 2008 | Panasonic SC-HT75 System

2 Answers

Cannot get BluRay/DVD system to respond to remote commands. Only the Samsung TV will. I cannot figure out how to switch the remote into giving only BluRay/DVD functions. I've read this unit has a...


Yes, the reason for this is that the BD-Receiver/TV button was pressed twice. This button has 2 modes of operation depending on the color it flashes when you press any button on the remote. If the BD-Receiver/TV button flashes green then it is in TV mode and if it flashes orange then it is in BD Receiver mode. The way to switch between the 2 modes is simple but not intuitive and easily not noticed. Simply press the BD-Receiver/TV button it will light-up green or orange, depending on what mode it is in, for about 1 second. The trick is to quickly press it again BEFORE the light goes out. When this is done the color of the light will change. If it was green it will change to orange and vice versa. Rember, Orange = BD Receiver function Green = TV
Hope this solution has been helpful?
Thank you for visiting FixYa.

Aug 20, 2011 | Samsung HT-C6730W Theater System

1 Answer

Dvd player goes through the motions then says no disc why


hope you're using a good dvd... but if this is happening more often... just bring it back to the store or to the authorized service center if its still under warranty.... if not, try this simple steps...(1) try to insert a optical lens cleaner cd if available.... (sometimes a dirty optical lens is the cause of the problem...). once you cleaned the optical lens try to insert a good dvd... check if the problem is gone... if not (2) unplug the unit from the power supply socket. (3) remove the protective cover.. (4) plug the unit again to the power supply socket again. but please be careful not to touch the electrical circuit of the unit...(5) insert a good dvd... check if the dvd is spinning normally?... if not or too slow maybe the problem is the motor... (6) check if the optical lens is flashing a red light... if not, check the ribbon wire. check if its not broken... sometimes a broken ribbon wire may cause the problem. (7) if the the optical lens is flashing and the cd or dvd is spinning too fast than the normal speed, and the optical lens is moving back and port, and you hear a noisy sound like skipping. then the problem is the ptical lens... ty

Jun 18, 2011 | Toshiba Home Theater Systems

2 Answers

I have a Panasonic SA-PT960 surround sound/dvd player. Whenever I turn it on I get a chgr err flashing on the screen and a loud grinding noise


There is a fault with the DVD Changer and the noise is the gears grinding. This is a common fault with these units as a small arm within the unit breaks and blocks the mechanism.

You can either try and replace the complete DVD Changer or remove it and just us it as a surround sound system with your auxiliaries connected to it.

May 09, 2011 | Panasonic SC-PT960 Theater System with...

1 Answer

I lost the remote for my LG DVD receiver model number LHT754 and i cant chance the inputs


If u are trying to change the input from dvd to usb or the other inputs. All you have to do is hold down the play button on the front of the dvd home theater system until it starts to flash then press it again and keep pressing until u find the input u are looking for. It will rotate thru all inputs even the ipod input.

Sep 26, 2010 | LG LH-T754 Theater System

2 Answers

Dvd carousel will not open


The best solution would be to unplug the unit and attempt to remove the top cover or lid and remove the disc from the platter, many units will unscrew from the sides and back panel.

Feb 22, 2009 | Sony DAV-S400 System

1 Answer

SONY DAVDZ361 HTK


have you checked the ID matches the same as the unit, I.E A on the wireless unit and A on the dvd player,?

what is the wireless unit light status? flashing green???
if flashing and you have tried messing around with pairing best way is to switch the wireless unit to A then do a reset on the unit, cant remember the exact button combinations, it will be in the instructions, something like press stop, pause and power at once. but check the instructions that should solve it, if not email me on eamonnl2004@hotmail.co.uk i will try help you there

Jan 01, 2009 | Sony BRAVIA DAV-HDX267W Theater System...

1 Answer

Is it multiregional


Sony are probably the most protective manufacturer of this kind of information. All manufacturers carrying a DVD logo are obliged to say "no" but will normally intentionally leak this to boost sales, particularly in non-US areas.


But try this:

1. In order for this hack to work, you will have to send an infra-red code to your player with a OneForAll remote such as the OneForAll 6 (or URC7560) or OneForAll 4 (or URC7740) or OneForAll 4 Digital, or One For All 5 Digital (or URC 7555) with the following instructions:
  • Press the DVD button
  • Hold down the Magic button until the unit performs a double LED flash
  • Configure your remote using the setup code 0 5 3 3
2. On your DVD recorder, using the official Sony remote, select the System-Menu option 3. On your DVD recorder, using the official Sony remote, select the Setup option 4. On your DVD recorder, using the official Sony remote, select the Options option 5. On your DVD recorder, using the official Sony remote, select the Command-Mode option 6. On your DVD recorder, using the official Sony remote, select the DVD1 option 7. On the official Sony remote, set the DVD1 option for the Command-Mode switch, under the sliding cover 8. Verify that both the official Sony remote control and your OneForAll remote control can power off and on your DVD player 9. Program your OneForAll remote with the following instructions:
  • Hold down the Magic button until the unit performs a double LED flash
  • Configure your remote using the setup code 9 9 4 or 0 0 9 9 4 if your remote only accepts 5 digit codes
  • Press the Magic button once
  • Configure your remote using the setup code 1 8 9 or 0 0 1 8 9 if your remote only accepts 5 digit codes
  • Press the 1 button once, a double LED flash should occur
10. Program your OneForAll remote with the following instructions:
  • Hold down the Magic button until the unit performs a double LED flash
  • Configure your remote using the setup code 9 9 4 or 0 0 9 9 4 if your remote only accepts 5 digit codes
  • Press the Magic button once
  • Configure your remote using the setup code 2 5 5 or 0 0 2 5 5 if your remote only accepts 5 digit codes
  • Press the 2 button once, a double LED flash should occur
11. Program your OneForAll remote with the following instructions:
  • Hold down the Magic button until the unit performs a double LED flash
  • Configure your remote using the setup code 9 9 4 or 0 0 9 9 4 if your remote only accepts 5 digit codes
  • Press the Magic button once
  • Configure your remote using the setup code 0 9 5 or 0 0 0 9 5 if your remote only accepts 5 digit codes
  • Press the 3 button once, a double LED flash should occur
12. Program your OneForAll remote with the following instructions:
  • Hold down the Magic button until the unit performs a double LED flash
  • Configure your remote using the setup code 9 9 4 or 0 0 9 9 4 if your remote only accepts 5 digit codes
  • Press the Magic button once
  • Configure your remote using the setup code 2 2 1 or 0 0 2 2 1 if your remote only accepts 5 digit codes
  • Press the 4 button once, a double LED flash should occur
13. Program your OneForAll remote with the following instructions:
  • Hold down the Magic button until the unit performs a double LED flash
  • Configure your remote using the setup code 9 9 4 or 0 0 9 9 4 if your remote only accepts 5 digit codes
  • Press the Magic button once
  • Configure your remote using the setup code 0 7 9 or 0 0 0 7 9 if your remote only accepts 5 digit codes
  • Press the 5 button once, a double LED flash should occur
14. Place your DVD player into Standby mode 15. Press the buttons 1, 2, 3, 4 and 5 on your OneForAll remote control, in order, one at a time 16. Your DVD player should show the words TIMER OK 17. Press the buttons 1, 2, 3, 4 and 5 on your OneForAll remote control, in order, one at a time 18. Your DVD player should return itself to Standby mode 19. Remove the batteries for significant period of time to wipe the programmed codes on your OneForAll remote

Nov 27, 2007 | Sony DAV-S500 System

6 Answers

FAC-FC7 DVD player is locked and the Standby indicator flashes


I had the same problem and searched FIX and found a solution for a Phillips DVD player that worked on my Sony DAV-FC7 dvd player. Someone posted that they called their Phillips Tech Service and was told to (a) unplug the dvd unit from the wall and wait 20 seconds,then (b) press the standby+plug the unit back into the wall at the same time and hold for 10 seconds. I did this for my Sony DAV-FC7 which would not power on nor eject (just red light on). IT WORKED!! after doing these steps, my SONY powered on and the rented DVD ejected. The dvd palyer works again. Thanks fellow FIXYA "posters".

Nov 12, 2007 | Sony DAV-FC7 System

Not finding what you are looking for?
Panasonic SC-HT75 System Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Home Theater Systems Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5625 Answers

Are you a Panasonic Home Theater System Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...