Question about Wireless Access Points

1 Answer

Power - Wireless Access Points

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

Please describe your issue in full

Posted on Jun 06, 2008


Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blinking power and link led


Hi There - in my experience, blinking power lights on routers mean faulty power supplies - the Power Adaptors are prone to failure after long periods of continuous use - I would find out what voltage and current consumption is required for your router (usually printed on a label on or near the power socket in very small writing), then buy a replacement adaptor - you don't need to get the exact same item, one which can be adjusted to give different voltages should work just as well if you can match the voltage and power rating your device needs - You can use an adaptor with a higher power rating but don't use one with a lower power rating

Nov 12, 2013 | Linksys Wireless-G WAP54G 802.11g/b...

3 Answers

How do I disconnect and reconnect my modem?


This should be as easy as pulling the plug from the wall, waiting 30 seconds or so, and then plugging it back in.

Mar 18, 2011 | 2wire Wireless-G 802.11g ADSL Gateway

1 Answer

The power of my Linksys Wireless-G Game Adapter [ WGA54G ], isn;t coming on! I was wondering if there is a switch to turn it on!


With Linksys game adapter there's no power switch on it when you plug it to a power outlet if adapter is working the light should come on.

You can follow these troubleshooting to determine if adapter is really bad or something else.

Make sure that the power adapter that you are using came with the wireless gaming adapter.
Power adapter is connected properly to the back of the adapter and the electrical outlet.
Electrical outlet is preferably a surge protector.
Try another electrical outlet.
Unplug and replug the power adapter.
Hold the reset button for a minute, while the adapter is connected to the electrical outlet.
If there is still no power light then it is possible that the adapter is defective, and have it replace if still under warranty.

Oct 07, 2010 | Linksys Wireless-G Game Adapter [ WGA54G ]...

1 Answer

My wireless assistant won't turn on?


Check to make sure there is power to the power adapter and the DC output is coming out on the end that plugs to the Access Point. if not replace the power adapter. If power is Ok replace the access point

Dec 27, 2009 | HP Wireless Access Points

1 Answer

Cannot get power to my router....and yes there is enough power through the outlet


Your power adapter is bad. You can get a universal power adapter for those.

Dec 17, 2009 | Dynex Enhanced-G Wireless Broadband Router

1 Answer

Earlier today I had a Red Power light and only a green wireless light. Now I have no lights when I plug in the 2wire router / modem. Is the equipment dead or is there something I can do besides replace...


Try the following steps:
1. Disconnect the 2wire gateway power adapter.

2. Reinsert the power adapter directly into the wall socket.

3.Remove any power strips or surge protectors temporarily to ensure that these items are not preventing the 2wire gateway proper operation.Note: Make sure that you are using the power adapter that came with your 2wire gateway.

4. Plug the power adapter into a different wall socket in another room.

5. Press the red factory reset button if available.

6. If the power light is still red, then you will need to replace the 2wire gateway.

Nov 27, 2009 | 2wire Wireless-G 802.11g ADSL Gateway

1 Answer

Wireless power problem


After researching Cisco site. And testing. I suggested the coutomer log on to the device and adjust settings. It turns out the unit when using a power injector goes into a Power Managment mode. The unit goes to half power and can cause problems.
Thanks for the help.

Jun 10, 2008 | Cisco Aironet 1131AG 802.11a, 802.11g/b...

1 Answer

Missing power supply


locate the bottom of ur AP and read the following u should find these values:

Voltage: described by volts EX: 5 v or 12 v

Amperage: described by amperes EX: 500 ma , 1 A,....

Polarity: whre is minus and plus

write these values and u can buy any power supply or power adapter based on these values if not sccseeful write me ill help u more

wafik_eid@hotmail.com

Nov 21, 2007 | Arris WA840G 802.11g/b (49832000100)...

1 Answer

How do I power cycle the Modem and Router?


Power OFF the Cable/DSL Modem, then the Router and wait for couple of minutes. Now power ON the Cable/DSL Modem First, after the modem gets initialized, Power ON the router.

Feb 19, 2006 | SMC Barricade 7004

1 Answer

How do I power cycle the Modem and Router?


Power OFF the Cable/DSL Modem, then the Router and wait for couple of minutes. Now power ON the Cable/DSL Modem First, after the modem gets initialized, Power ON the router.

Feb 19, 2006 | SMC Barricade 7004

Not finding what you are looking for?
Wireless Access Points Logo

Related Topics:

233 people viewed this question

Ask a Question

Usually answered in minutes!

Top Wireless Access Points Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

noti13

Level 1 Expert

15 Answers

Mike

Level 3 Expert

4331 Answers

Are you a Wireless Access Point Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...