Question about Food Processors

1 Answer

Robot coupe r 301 ultra

How do I remove the motor? I think I have to hold the shaft by the fan blade and turn the mixing shaft, but is it clockwise or ccw?

Posted by on

  • Eazy Eric Jun 06, 2008

    Does anyone know how to remove a motor on a Robot coupe R301 Ultra?

  • netcafe94 Jul 25, 2008

    my name is robert 07717822100 my robocoup stop working,i check the fuse ,is ok,can you fix my mashine

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Remove the base the screws are under the rubber feet,on top of the machine there are three screw caps remove these with a bradel, unscrew screws with large torx screw driver, remove spindle anti clockwise by locking out fan at base. for all Robot coupe parts go to http://www.catering-machines.com/

Posted on Sep 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove and install on/off pin for robot coupe r2


Thanks so much for the advice. Any idea what size TORX is required?

Jan 08, 2012 | Robot Coupe R2Dice Ultra Food Processor

Tip

Bringing and blending aplliances


Generally, a blade or grinding or blending/mixing part that is permanently attached to a metal shaft from the appliance motor is held on that shaft by a 'shear pin'. This pin breaks when something is put in the appliance that the grinder, mixer, blender can't gring, mix, or blend. This is to protect the motor from overload. Afterwards, The motor will continue to turn, but the blade or paddle, or whatever will not turn.
The shear pin needs to be replaced.
The shear pin passes through one side of the base of the bade/grinder/paddle assembly, through the motor shaft, and out the other side of the blade/grinder/paddle.
The piece of the pin must be removed from the shaft, and from the two sides of the blending/grinding part. This is generally a press-fit, and some effort may be required to accomplish this.
When the pieces have been removed, a common 'roll pin' of the appropriate diameter should be inserted to hol the turning part on the shaft. It must fit tightly, and some effort should be required to insert the new pin. // '); }// ]]> Back to Edit // '); }// ]]> Publish preview_graphic.jpg

on Feb 07, 2010 | Food Processors

1 Answer

The robot coupe will stop working periodically during use. The reset button on the bottom pops out after it has been used for a short while. I run a kitchen and it can be very frustrating trying to get...


It is overheating, probably because it is being overworked. Some common problems are overloading the bowl, or forcing too much food into the hopper on top. Once it overheats, it will kick out again rather quickly the next time unless the motor has time to cool. If you are shredding cheese, slow down on the amount of cheese forced into the blade. If you are trying to mix heavy dough you are probably overloading the bowl as well. This machine can't handle over a pound of pizza dough without overheating. The reset button is there to keep from burning the motor out. If you continue to reset and force feed the machine, it will burn the motor out. Good luck, hope this helps.

Sep 11, 2010 | Robot Coupe R2U Ultra Food Processor

1 Answer

I have a Robot Coupe R2 food processor that quite


It just a long shaft phillips screwdriver. The screws are located under the foot pads. They just pull out and then there are the four screws.

Dec 29, 2009 | Robot Coupe R2U Ultra Food Processor

1 Answer

Looking for spare parts for a Robot Coupe R301 Ultra Food Process


Robot-Coupe USA.com should be able to sell you anything needed

Jul 09, 2009 | Robot Coupe Food Processors

1 Answer

How do i seperate the housing on a robot coupe processor


There are 4 rubber shoes on the bottom of the white or gray base. Twist & pull these out. With a TORX long shank screwdriver (nothing else works, trust me) there is a screw way down in each hole. After removing the screws a gentle but firm bump should loosen the base. If you ever need to replace the motor, on the top around the drive shaft you will see three round plugs/disks, remove them by prying up with a pocket knife (works best) this will give you access to the three motor bolts.

Feb 20, 2009 | Food Processors

1 Answer

Robot coupe maintanance


That plastic piece is a sling disk or sling blade and made to sling product to the discharge chute. Believe it or not, the motor shafts wear out and could be the cause of premature failure. When you install the new sling blade, check to see how much slop/ play there is by moving this back and forth on the shaft, a small amount is ok (1/16th to 3/32nds). The other thing to look at is forcing or overfeeding the unit. You can contact them at Robot-coupeusa.com

Nov 15, 2007 | Robot Coupe CL50 Food Processor

1 Answer

How do I assemble the Robot Coupe R 2 Ultra


Cindy,
Send me your e-mail & I will send you back an exploded view of your Robot-Coupe. It will give all the info needed. capt_rick1912@yahoo.com

Nov 02, 2007 | Robot Coupe R2U Ultra Food Processor

Not finding what you are looking for?
Food Processors Logo

Related Topics:

779 people viewed this question

Ask a Question

Usually answered in minutes!

Top Food Processors Experts

Ryan S
Ryan S

Level 2 Expert

328 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

clay_pots_47
clay_pots_47

Level 1 Expert

7 Answers

Are you a Food Processor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...