Question about Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

1 Answer

Frigidaire PLD2560LCC1 error codes, not in owners manual

Thanks for the feedback, but I went through every page of the manual, with not luck, they aren't published. Any other suggestions?

Posted by on

  • David Emmel
    David Emmel May 11, 2010

    Have received no response. Will e-mail 2nd request and update tomorrow.



    Thank you for yyour patience!

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 525 Answers

You may want to try one of our on line experts to get a better solution.

Sorry I was unable to help.

Dave E. (Illeagle)

Posted on Jun 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Electrolux PLD2560LCC1 lights flashing


Good Morning Friend,

I understand that you have flashing lights on your Frigidaire dishwasher, model# PLD2560LCC1, and will not start the cycle. I suggest resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 20-30 minutes. Restore power and try running the cycle again. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your refrigerator status has changed successfully. Hope this is helpful.

-Best Regards-
WP

May 27, 2014 | Frigidaire Dishwashers

1 Answer

Frigidaire Gallery Professional Series GPD8998JC0 ... I can press the buttons to choose my settings but my START/CANCEL button won't work. So I try a 1 hour delay which works but then no water nor the...


Hi Joseph - I understand your dishwasher is displaying a "CL" error code. A "CL" code typically refers to the main door switch. The first easy troubleshooting tip is to flip the circuit breaker to the dishwasher for about 20 minutes and see if that resets it and clears the error. If the circuit breaker trick doesn't work, it could potentially mean that the door is not closed completely. However, it could also mean that the control board is not sensing that the door is properly closed. I would recommend checking the door switches. Look to see if you notice if anything is bent or misshapen. Also, you might try the manufacturer site to see if you can download an owner's manual for future reference. They typically have a large number of owner's manuals for consumer use. If you have tried these troubleshooting tips and still come up with a "CL" code, you might need to reach out to a local service tech who can better pinpoint the problem for you. Best of luck!

Dec 19, 2013 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Frigidaire model number gld 2250, gld 2240


read your owner manual section troubleshooting and see the
problem for e.codes.
if you do not have it download from www.retrevo.com

or get support from frigidaire via online, chat or phone
God bless you

Sep 24, 2012 | Frigidaire Professional Series 24 in....

1 Answer

My Kenwood dishwasher keeps displaying error message E4 but there is no mention of this in the user manual. Can you explain what this means


Hello,

Some models of Frigidaire washers come with a digital readout display that informs the operator of the unit's function and any errors.

Error codes indicate that a problem has occurred and should be addressed. Different models of Frigidaire washers may vary in their fault displays.

Some washer models use flashing lights at the unit's start, door lock, wash, rinse, final spin and control indicators to display error codes.

Hope this help?

Thanks.

Nov 02, 2010 | Kenwood KDW243A Builtin Dishwasher

1 Answer

Pf code came on and then went to er code reset power and pf code comes up then starts showing 37-36


Hi,

Here is a tips that I wrote that will help to explain why you get the PF Error Code

PF Error Code for Appliances


heatman101



,./;''l

Jun 18, 2010 | Frigidaire 24 in. PLD2560LCC Energy...

1 Answer

Frigidaire dishwasher not completing cycle.


hi,
The cycle doesn't complete
If the cycle doesn't complete, check these:

Water-heating cycle
Timer

Water-heating cycle
Many dishwashers heat the wash and/or rinse water to a higher temperature, as the cycle calls for it. In these cycles, the dishwasher pauses after it has filled with water, waiting for the water to reach the pre-set temperature. What happens next, depends, as follows:

On some units, the pause is timed and the unit continues after the allotted time. 

On others, the cycle can't continue until the water reaches the higher temperature. If you have this type of dishwasher and the water isn't being heated (say, because of a problem with the heating element or thermostat), after the unit stops at the heating cycle, it never continues. When you repair the heating-system problem, the "cycle problem" is fixed too. 

Timer
Timers don't often fail. But if every other part of the dishwasher seems to be working properly and the timer knob seems to be stuck in one place--doing one function continuously--the timer may be at fault. Dishwasher timers can't be repaired. If yours is defective, replace it. 

I see an error code
If your dishwasher has a digital readout and you see an error code, it may indicate a problem with the unit. If this happens, look up the error code in your owner's manual to find out what the problem is.

Good Luck
Thanks for using FixYa

Jan 03, 2009 | Dishwashers

9 Answers

Dishwasher er error code


I have a similar problem with my Frigidaire FDB4050LHS1. My Owner's Manual says to contact the Customer Care Center if the display shows "Er", "uF", or "CE". When I called them, Maria didn't have a clue what the codes meant - all she could do was give me phone numbers to authorized service centers in my area.

I managed to get ahold of a "SERVICE DATASHEET" P/N: 154718601. The error code "ER/ER" means there is a "switch failure"; "ER/CE" denotes a "Configuration Error"; "ER/uo" means "Vent will not close"; and "ER/UF" means "Fan not running".

The schematic only labels three switches - labeled "USER INTERFACE SWITCH", "DOOR SWITCH", and "FLOAT SWITCH". There is also a switch in the pump motor assembly. If either the door or user interface switch is faulty, then you probably won't be able to do anything other than call a repair service - unless you know how to replace these switches yourself.

If the float switch is causing the error, you might be able to run the "Water/Service Test". From "PF" (denoting a Power Failure) or idle mode (with no lights on whatsoever), press and hold the "DRY/AIRDRY" and "START/CANCEL" buttons at the same time for 3 seconds. This will start an 8-stage test that runs for about 7 and 1/2 minutes. The display will show which step the test is in until it shows an error code. Step 1 tests the water valve, which is where the float switch is located. If that switch is bad, you will likely see "Uo" displayed within the first minute of the test.

Aug 24, 2008 | Frigidaire 24 in. FDB1050REC Stainless...

2 Answers

Frigidaire professional series dishwasher, PLD2560LCC1


the control on the dishwasher is locked look on the console to see the unlock button it will be in you owners manual this is the problem

May 09, 2008 | Frigidaire 24 in. FDB1050REC Stainless...

Not finding what you are looking for?
Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher Logo

Related Topics:

473 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Dishwashers Experts

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Carmen Mikulic

Level 2 Expert

409 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Frigidaire Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...