Question about Blaupunkt Car Audio Receivers

Open Question

Blaupunkt Boston CC20 - How do I instal code?

I cannot work out which button is 'station+' which I have to press after entering each code digit.
I have only got Scan, Balance and Tone buttons, plus rocker switches
3U-T/M-L, PS/Mode, FF/Eject, and the Channel buttons 1 to 5.

Posted by on

6 Suggested Answers

KaeZoo
  • 156 Answers

SOURCE: power will not stay on

Sounds like you're not getting voltage on the accessory power lead. This is the red wire at the back of the deck, and it supplies power whenever the key is switched on. It's possible that your vehicle's radio fuse is blown.

Posted on Aug 11, 2007

  • 1 Answer

SOURCE: blaupunkt cancun cr63 car radio

I'm having the exact same symptoms and have had the same luck online. My guess is that the logic got fried during the "brown out" while trying to crank the engine on a very low battery. I thought I might find something about the "VF" and "SK" modes that it is getting into (pretty cool if I weren't missing my radio stations). I'm guessing they are European bands or something. Also getting into a CD changer mode - funny since this was a pretty low-end cassette tape model. My Cancun is 12 years old. What I'm going to try (when it stops raining) is to disconnect the battery leads for 15 minutes or so and then reconnect to see if that clears out the radio memory (if I could easily identify the correct fuse, that would make the process much easier but, alas, I can't). Let me know if you have tried anything else and I'll let you know if my attempt works.

Posted on Aug 18, 2007

SparkGap
  • 363 Answers

SOURCE: cannot tune to local stations

- The 0.2MHz odd steps are standard for US radios. Try resetting the radio (recessed button under the front panel) If this a US radio then this may not help. If you have lost the manual then go here:- http://books.jvcservice.com/booklist.asp?Model=KD-G400 Come back and say if this helped or not, I could dig a bit deeper.. -

Posted on Oct 04, 2007

  • 1 Answer

SOURCE: BLAUPUNKT GMDAT CDP 3 (E) - CAR RADIO CD HOW TO EJECT CD?

Hi graz,

If your unit has a SRC button to the right of the CD clot, try holding this down for a few seconds - works on mine!

Posted on Feb 28, 2009

  • 4706 Answers

SOURCE: lost my radio manual but have code

Blaupunkt Boston CC-22 Code Entry 
Turn on the radio, the display will show 'COD'

Press preset [ 1 ] repeatedly for the first digit followed by [ station + ]
Press preset [ 2 ] repeatedly for the second digit followed by [ station + ]
Press preset [ 3 ] repeatedly for the third digit followed by [ station + ]
Press preset [ 4 ] repeatedly for the fourth digit followed by [ station + ]

Finally press the [ station + ] button to save. 



Posted on Sep 06, 2009

  • 4706 Answers

SOURCE: i need unlock code for blaupunkt malibu c50

The radio will have to be removed from the car dashboard .

Then please quote the MAKE + MODEL of your radio plus ALL the LETTERS and NUMBERS on any LABELS , BARCODES or STAMPED IN THE METAL CASING.


Also quote the MAKE of CAR it is fitted into.


Posted on Sep 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Locked out


The setup Security Code can be done when the
<Demonstration mode Setting> (page 50) is set as OFF.
• When the Security Code function is activated, the code
can’t be changed and the function can’t be released.
Note, the Security Code can be set as the 4 digit number
of your choice.
1 Enter Standby
Press the [SRC] button.
Select the "STANDBY" display.
2 Enter Menu mode
Press the [MENU] button for at least 1 second.
When "Menu" is displayed, "Security" is displayed.
3 Enter Security Code mode
Press the Control knob for at least 1 second.
When "Enter" is displayed, "Security" is displayed.
4 Select the digits to enter
Push the Control knob to [4] or [¢].
5 Select the Security Code numbers
Push the Control knob to [FM] or [AM].
6 Repeat steps 4 and 5, and complete the
Security Code.
7 Confirm the Security Code
Press the Control knob for at least 3 seconds.
When "Re-Enter" is displayed, "Security" is
displayed.
8 Do the step 4 through 7 operation, and
reenter the Security Code.
"Approved" is displayed.
The Security Code function activates.
• When the wrong Code is entered in steps 4 through 6,
repeat from step 4.
Press the Reset button and when it’s removed
from the battery power source
1 Turn the power ON.
2 Do the step 4 through 7 operation, and enter
the Security Code.
"Approved" is displayed.
The unit can be used.
In Standby mode
Touch Sensor Tone
Setting the operation check sound (beep sound)
ON/OFF.
Display Setting
"Beep : ON" Beep is heard.
"Beep : OFF" Beep canceled.
In Standby mode
Manual Clock Adjustment
• This adjustment can be done when the <Synchronize
Clock> (page 43) is set as OFF.
1 Select Clock Adjustment mode
Push the Control knob to [FM] or [AM].
Select the "Clock Adjust" display.
2 Enter Clock Adjust mode
Press the Control knob for at least 1 second.
The clock display blinks.
3 Adjust the hours
Push the Control knob to [FM] or [AM].
Adjust the minutes
Push the Control knob to [4] or [¢].
4 Exit Clock adjustment mode
Press the [MENU] button.
The Whole manual is here.
http://www.kenwood.net-disp.com/i/05products/kdc_x789/pdf/kdc_x889_x789_mp828_k_english.pdf

Dec 06, 2007 | Kenwood KDC-MP628 CD Player

1 Answer

I cant get the sirius to go past channal 39 it is telling me that the channales are preset. i dont have the manual for the stero so i dont know how to get all the channals to work.


  • [P/A] button Performs category scan while in the SIRIUS mode.When the button is pressed and held, preset scan is performed.
  • [DIRECT] buttons Stores a station into memory or recall it directly while in the SIRIUS mode.
  • [ > '' ] (play/pause) button Select a category [<<] rewind, [>>] fast forward button Press the button to select a station.
  • [FNC] button Press the button to switch the operation mode among the SIRIUS mode, etc.

Nov 17, 2010 | Clarion DXZ845MC CD Player

1 Answer

Put in code but could not press enter, entered code but nothing happend so entered it again now its locked


leave it switched on..undisturbed for as long as it takes to automatically reset itself.

If your radio is a BP Lausanne then the code entry instructions are

Blaupunkt Lausanne CD30 Code Entry
Turn on the radio, the display will show 'CODE' followed by '0000'

Press preset [ 1 ] repeatedly for the first digit
Press preset [ 2 ] repeatedly for the second digit
Press preset [ 3 ] repeatedly for the third digit
Press preset [ 4 ] repeatedly for the fourth digit

Finally press the [ station ^ ] button to save.



blank.gif _uacct = "UA-277454-2"; urchinTracker();

May 05, 2010 | Blaupunkt Lausanne CD31 CD Player

1 Answer

Security code harman kardon


Hi there,
I think its fairly standard across all Land Rovers. You only actually need numbered button <1> and the two seek buttons that look like <| and >| .
-------------
When you turn the radio on, you should see it request <CODE>

Press preset button <1>. This should identify character 1 of the code.

Use one of the two tuning buttons (Seek up , or seek down - the ones with arrows going into lines) to move to the right number (0-9).

Press preset button <1> again to lock digit 1 and move onto code digit 2.

Repeat twiddling the upseek and downseek. Press button 1 etc .... until all four codes have been entered.

When you press <1> for the final time, if the code is correct, you'll get a two tone beep to confirm and the radio is unlocked.

If incorrect, you are progressively locked out (in doubling time periods).

Hope this helps.

Jan 03, 2010 | Alpine TDM-7561 Cassette Player

2 Answers

I need to know frequencies and how to program a bearcat 148xlt


To program the Bearcat 148xlt, press the manual button and then enter your code, for example:"123.456" after you enter the code, push E and then press the manual button again to enter a new code like "567.987" then press E, when all of your codes are entered press the scan button to finish. Try http://www.scannermaster.com
or http://www.radioreference.com for some frequencies to add to your scanners database

Dec 16, 2009 | Car Audio Receivers

1 Answer

How do i enter the code in a 98 polo radio?


Hi,

Once you have the unlock code, then turn on the radio. You should see SAFE displayed. After about 3 secs, "0001" should appear. Use the station preset buttons 1 thru 4. Preset 1 changes the first digit of the code, and preset 2 changes the second digit, etc. Enter all 4 digits of the code. After code is entered, press right side of "Seek" button for about 2 seconds, until an audible signal is heard. If you hose up and get the wrong code...will go back to SAFE displayed. You will get another chance to enter the code. After 2 failed attempts, you have to wait 1 hour again for it to unlock. So carefully enter the correct code the first time.

In case, problem persists, let me know.

Thanks.

Sep 07, 2009 | Car Audio Receivers

1 Answer

Lost my radio manual but have code


Blaupunkt Boston CC-22 Code Entry 
Turn on the radio, the display will show 'COD'

Press preset [ 1 ] repeatedly for the first digit followed by [ station + ]
Press preset [ 2 ] repeatedly for the second digit followed by [ station + ]
Press preset [ 3 ] repeatedly for the third digit followed by [ station + ]
Press preset [ 4 ] repeatedly for the fourth digit followed by [ station + ]

Finally press the [ station + ] button to save. 



Jan 07, 2009 | Blaupunkt Boston C32 Cassette Player

1 Answer

Entering radio code


To enter the radio code on most Renaults you do not use the buttons on the radio. Instead use the remote control buttons on the steering column.

The remote control has a rotary control, (either vol +/- or track/station +/-), use this to set each individual digit.

The bottom button on the controller moves to the next digit of the code.

When you have the correct code on the display, press and hold the bottom button to enter the code.

You should hear a beep and the radio should start up.

You have 3 attempts to enter the code. If an incorrect code is entered 3 times, then the radio will lock up for about 30 mins before it will allow you to try again. If this happens 3 times, then the radio will lock up permanently.

If you don't have the correct code, or the radio is locked, then there are companies which can re-code the radio.

May 02, 2008 | Car Audio Receivers

2 Answers

Need to find out the four digit code



KENWOOD SECURITY CODE CLEAR procedure


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

The security is canceled and the set enters the TUNER mode!

Dec 14, 2007 | Car Audio Receivers

Not finding what you are looking for?
Car Audio Receivers Logo

Related Topics:

798 people viewed this question

Ask a Question

Usually answered in minutes!

Top Blaupunkt Car Audio Receivers Experts

xxxxxx xxx

Level 3 Expert

4706 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

yadayada
yadayada

Level 3 Expert

60541 Answers

Are you a Blaupunkt Car Audio Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...