Question about Dewalt DC011 AM/FM Radio

3 Answers

Dewalt dw911 radio

I have removed the 8 screws holding the case together and can't figure out how to separate the front from the back. It acts like it's glued together.  Can you off some idea as to how to get inside the radio? 
The radio works fine, but the charger doesn't work. I'm assuming that it's just the fuse.
Thanks

Posted by on

  • thomdo Jun 05, 2008

    Great solution!!! Thanks

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

I had the same problem with the case not coming apart after I took the screws off, but thanks to someone posting a suggestion on this website, I was able to take it apart and take care of the problem. Use a soft mallet and use it around the seam of the radio until it pops loose.

By the way, my original problem with the radio was that it would not get any power at all, whether using the power cord, or an 18v battery. I was able to fix the problem by replacing the fuse located inside the case (250v / 1AMP)......works great now!! Many thanks to all of you who posted suggestions on this great website!!

Posted on May 03, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,141 Answers

TURN THE UNIT OVER AND REMOVE THE TWO SCREWS FROM THE REAR THIS WILL SOLVE THE PROBLEM.

Posted on Jun 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Dewalt radio (Dw911) that will only play off the battery, not the power cord. I have checked both fuses and found both to be good. It sounds as if this is a common issue but I have found no...


Mine had the same problem .Try swapping the fuses. Although the fuse looked good mine was bad. Easy fix I hope. Going to auto parts store for new ones.

Oct 09, 2010 | Dewalt Personal Radios

1 Answer

Dewalt radio dw911 will play on mains but nothing with battery only


If you pull of the back cover you will find two small fuses near power supply, one of these allows power from battery pack, check with voltmeter for open circuit, I take it that it is not just one battery it does this with.

Nov 27, 2007 | Personal Radios

1 Answer

My dewalt dw911 radio/charger works on either mains or battery but wont charge a battery and blows an internal fuse when both are used together


More than likely your internal charger is faulty. Inside your inernal charger unit check the 2 anmp fuse which is white in colour.

Oct 24, 2009 | Dewalt DC011 AM/FM Radio

1 Answer

DeWalt DW911 Dis-assembly Problem


look on the back of the radio theres two more screws by the mounts for the cage

Feb 18, 2009 | Dewalt DC011 AM/FM Radio

3 Answers

DeWalt DW911 Radio/Charger


the second fuse is behind the circuit board,in middle of the radio.
there are 4 screw holding circuit board. Still looking for 2 AA battery.

Oct 09, 2008 | Dewalt DC011 AM/FM Radio

1 Answer

Dewalt radio dw911


Have you changed the AA Batteries, this is often the fault, when they are flat they lock the radio out. HHM Dewalt Service

Nov 27, 2007 | Dewalt DC011 AM/FM Radio

1 Answer

DEWALT DW911


2 screws sunk in at the back left and right. no need to remove speaker screws.

Oct 27, 2007 | Dewalt DC011 AM/FM Radio

6 Answers

Dewalt DW911 jobsite radio


Got mine open.

There was a fuse inside - Replaceable - fixed the problem.

There were no hidden screws, none under stickers or in the battery box like suggested by others, and the 2 magic release screws not so. There are several deep screws requiring a long philips, but the entire seam is glued (why?) so to open the radio I had to hit the body near the seam with a rubber hammer to crack the seam loose once all the screws were removed, comes right apart. Put it back together without glue, just the screws, it will be fine.

Sam. DesertSolutions.net

Sep 06, 2007 | Dewalt DC011 AM/FM Radio

1 Answer

Dewalt Radio


take all screws out of front perimeter, then there are 2 screws on the back at the bottom right and left you have to look close these screws are deep.

Jan 31, 2007 | Dewalt DC011 AM/FM Radio

Not finding what you are looking for?
Dewalt DC011 AM/FM Radio Logo

Related Topics:

1,294 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Personal Radios Experts

masterwest

Level 1 Expert

45 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Gyula Lacz

Level 3 Expert

482 Answers

Are you a Dewalt Personal Radio Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...