Question about Kicker 03KQ9 9-Band Car Equalizer

1 Answer

Power connection i bought used kicki er kq9 eq without power connector i need to know what pins go yo what

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 28 Answers

Look at the back it should show you
power, ground and remote

Posted on Dec 04, 2008

  • ALPHANSO TAYLOR Dec 04, 2008

    look at the back it should show you
    power, ground and remote


×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jet sound equalizer js 214 wire color code


Black wire is ground, Red with 5a fuse is hot. Green/black is L Ground BTL, Grey /black is right ground BTL, the RCAs are left and right low level inputs. Then there is the 5 pin connector. It has a red wire for +12v, two black wires for input grounds, a green wire for left Hi input and a gray wire for right high input. If you install using traditional common ground high level, then you don't used the two BTL wires. Just connect the wires from your 5 pin connctor. If you use the low level RCAs for inputs, then you only need to connect the red and black from your 5 pin connector.(Plus the main red and black) Make sure the switched on the bottom of your EQ are set correctly. COM for common ground and LOW for RCA input or High for Green/Gray wire input. If you are using a floating ground the select BTL and connect the two BTL wires to the floating grounds of your stereo. There is also a line input adjuster so you can adjust your input sensitivity to match your reciever. I have the owners manual if you have any other questions.

9aeedf67-4e84-4db3-95ec-85d417e14a1f.png


jet-sound-equalizer-js-214-wire-color#cmnt-3355757-zqfyadi1dvpmkuokso53jwn1-3-2.png


jet-sound-equalizer-js-214-wire-color#cmnt-3355757-zqfyadi1dvpmkuokso53jwn1-3-3.jpg


jet-sound-equalizer-js-214-wire-color#cmnt-3355757-zqfyadi1dvpmkuokso53jwn1-3-4.jpg


jet-sound-equalizer-js-214-wire-color#cmnt-3355757-zqfyadi1dvpmkuokso53jwn1-3-5.jpg

Feb 01, 2012 | Car Equalizers & Crossovers

2 Answers

Hi i just got a ava1202 boss eq it didnt have instructions this eq has rca inputs and high level speaker inputs can i use this eq with out an amp can smeone plz help me thnk u


Yes you can use the equalizer without an amplifier. That is what the high level speaker inputs are for. You simply take the positive and negative from a speaker and hook it up to the positive and negative high level speaker inputs on the equalizer.

Jun 04, 2011 | Boss AVA-1404 7-Band Car Equalizer

2 Answers

I have a 300 watt amp, but i just bought 12 gauge wire why wont it allow sound to come from my 12'' sub


There is no reason even if the wire was to small it would still allow ssound.make sure you have good connections.

Nov 08, 2009 | Pyramid 906 300 Watts (peak) 10 Band...

1 Answer

How to wire an eq to car stereo without an outboard amp?


no those wire is not for speakers out put that for signal in put only if there is rca jack follow the instruction and run your cable if your dont know dont guess you will burn unit audio out put if install wrong

Jun 28, 2009 | Power Acoustik PEQ-70 7-Band Car Equalizer

2 Answers

Power supply connection for pioneer eq-6500


top left - orange.....goes to aux or memory wire
top right - blue.......goes to the remote wire used with amps
bottom left - black.......goes to the ground wire
bottom right - red........this goes to your hot wire

May 31, 2009 | Pioneer EQ-6500 9-Band Car Equalizer

1 Answer

I need to find out the weiring diagrame to install it


Equalizers Like a crossover, the equalizer gets installed between your receiver and your amplifier. The outputs will be preamp connections to your amplifier. You'll find EQs that are designed to be installed in the dash, above or below your receiver. Others are designed to be mounted in a remote location, like the trunk. Either way, the wiring connections required will be the same. To install:
1. Mounting the equalizer:
A remote-mount EQ can be securely mounted with just a few screws. Anywhere between the receiver and the amp is fine. Most people mount the EQ in the trunk near their amp, especially if you have more than one amp. This also makes it easier to add additional amps later. You should mount it where it will be easy to get to so that you can make adjustments without too much trouble. Don't mount your EQ directly on steel — you will invite noise problems. Instead, install it on a non-conductive board and attach the board to the car body (or use rubber grommets under the screws to isolate the crossover).
An in-dash EQ can be mounted above or below your in-dash receiver, assuming that you have space available in the dash. This will require custom installation work. Another option is installation below your dash, in a universal under-dash mounting kit. To install the under-dash mounting kit, attach it to the mounting surface using the supplied self-tapping screws. In most cases, the use of an under-dash kit will require modifications to the kit or to the mounting surface.
3a-xover.jpg Locate the remote turn-on lead behind your radio (usually a blue wire). 3b-xover.jpg Connect the turn-on lead from your amplifier wiring kit to the blue wire. You can wrap the bare wire ends together and cover with electrical tape, or use solder. 2. Making the power connections:Your EQ will require 12-volt power, ground, and turn-on signal connections.
  • To obtain 12-volt power: Cut a length of small-gauge cable (16 gauge is typically sufficient) long enough to reach from the EQ location to your vehicle's fuse panel. Strip one end of the wire, and attach it to the EQ's power input. This may require a crimp-on connector, or bare wire might be sufficient, depending on the equipment you're installing. Route the wire from the EQ location to your car's fuse panel. Using a fuse tap, connect the wire to a source of switched 12V power.
  • To ground the EQ: Remove a bolt near the EQ mounting location. Crimp a ring terminal to one end of a length of small-gauge wire, and then bolt the terminal tightly to the vehicle's metal chassis. Scrape away any paint and clean the bolt location thoroughly. If you can't find a convenient ground screw or bolt, drill a hole for one — be careful not to drill into the gas tank or a gas or brake line.
  • Making the turn-on connection: In most cases, you can tap into your in-dash receiver's amp turn-on lead to get a turn-on signal for your EQ. Remove the receiver from the dash to access the turn-on wire (usually a blue wire). For step-by-step instructions on removing your vehicle's radio, see your vehicle-specific Crutchfield MasterSheet™, or read our In-Dash Receiver Installation Guide. Strip the insulation off a small section of this wire coming from the radio. Strip the insulation off another small-gauge cable that's long enough to reach from the in-dash receiver to the EQ, then connect the two with crimp caps or solder. Wrap the solder or crimp connection with electrical tape to guard against a short. Using wire ties to secure the wire, route the turn-on lead behind your dash all the way to the EQ mounting location.
3. Making the signal connections:
In most cases, you'll be routing RCA cables from your in-dash receiver's preamp outputs to the inputs of your EQ. While your receiver is out of the dash to access the turn on lead, connect a set of RCA patch cables (long enough to reach your crossover in its mounting location) to these outputs, taping them together so they won't come apart. Route the patch cables (again using wire ties) behind the dash, and to the crossover mounting location.

May 14, 2009 | Alpine Car Equalizers & Crossovers

1 Answer

Wiring problem


Usually Sony EQ's have a square, 4-pin connector on the back of them

If your looking at the back of the EQ, the upper left pin is +12V (power), the upper right is the Remote, the lower left it Ground, and the lower right is usually not used, but can sometimes be the Illumination circuit... but again, usually is not used.

Mar 21, 2008 | Sony XE-90MKII 9-Band Car Equalizer

2 Answers

Power connection


Theres supposed to be a harness that plugs into that connector. It will have the international color standard wires. Contact a kenwood dealer to get the harness.

Sep 14, 2007 | Kenwood KGC-6042A 9-Band Car Equalizer

1 Answer

Which wire is power and ground


generally red is the ignition wire, black is ground, orange is 12+ all the time, a yellow could be the same....it would be more helpfull if you would give the model number of the eq

Jul 13, 2007 | Kenwood KGC-4042A 5-Band Car Equalizer

Not finding what you are looking for?
Kicker 03KQ9 9-Band Car Equalizer Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kicker Car Equalizers & Crossovers Experts

auxpower

Level 1 Expert

18 Answers

Chen Dorot
Chen Dorot

Level 2 Expert

132 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Kicker Car Equalizer and Crossover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...