Question about Frigidaire FDE336RE Dryer

1 Answer

Belt diagram please give a diagram for this.

Posted by on

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 283 Answers

How's this?belt diagram - 355fd63.jpg

Posted on Aug 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Belt instillation diagram


Hi leanderson
You did not mention what brand your dryer is...so I will give you the one drawing I have to show belt routing on various dryers.
Please take time to rate me
Bud
3_23_2013_2_09_00_pm.jpg

Mar 23, 2013 | Dryers

1 Answer

How do you install the belt that turns the drum


I can send you a roper belt diagram it is easyer to email it to you just give me your email address and I will send you some illerstrations please give me a good rating if happy thank you

Dec 08, 2011 | Roper Dryers

1 Answer

Can you give me a diagram on how the belt is supposed to go?


Hello,

Here is the linkto belt diagrams http://www.repairclinic.com/Dryer-Belt-Diagrams#DiagramG

Just refer to the appx age of your model for the correct diagram


GENE

Sep 07, 2011 | Frigidaire GLER642A Electric Dryer

1 Answer

I have a hotpoint model# dlb2880aacad. The belt broke. I bought a replacement part, giving them the model number to ensure the correct belt. It seems too long, but I am not quite sure if i am putting it on...


The belt needs to go over the tension pully too. This will make up for the slack. Check the internet under your model for diagrams. Good luck!

Sep 03, 2011 | Dryers

1 Answer

Please show a picture of the route the belt takes on the pulley.


Hello,

this is a chart of belt diagrams for several brands http://www.repairclinic.com/Dryer-Belt-Diagrams
hopefully it will cover your brand..please in the future when writing in include your brand in the question.

GENE

Aug 28, 2011 | Dryers

1 Answer

Where do i find belt routing diagrams?


Go to repairclinic.com and click on the "Repair Help" link. On the following page, click on the "Dryer Belt Diagrams" link under the "Special Features" section. Depending on the model Kenmore you have, you will refer to either diagram H, B, or K. If you have trouble being able to determine which diagram you should use, please post back with your complete MODEL NUMBER so I can assist you further. I hope you find this information helpful.

Apr 21, 2010 | Kenmore 62602 Electric Dryer

1 Answer

Need to replace the dryer belt and have the dryer taken apart, how do i put the belt back on?


Thre are a couple of different ways, the dryer belt goes back on a Whirlpool manufactured dryer (including Kenmore). However, since you posted no MODEL NUMBER, I can only give the following advice:

Go to repairclinic.com and click on the "Repair Help" link at the top of the page. On the following page, look for the "Dryer Belt Diagrams" link under the "Special Features" section. Refer to diagram H or K.

If you aren't sure which configuration to use, please post back with your model number, so I can provide you with a more difinitive answer. I hope this helps you.

Jan 21, 2010 | Dryers

2 Answers

How do I access the belt on my Kenmore model


You have to get behind the dryer and remove the back. This will give you access to basically everything.

Nov 14, 2009 | Kenmore Dryers

1 Answer

Maytag electric dryer:attached belt as per directions,but is still loose,the pulley seems to not give enough tension


You can verify your belt installation by going to repairclinic.com. Click on the "Repair Help" link at the top of the page, then locate the "Dryer Belt Diagrams" link under Special Features. Refer to Diagram E under the Maytag heading. If you say you have the belt installed correctly, make sure the tension spring is still installed. I hope this helps you.

Jun 27, 2009 | Dryers

2 Answers

The belt has come off the dryer drum. I dont know how the tensioner goes back on


stick the belt pulley in the holes closest to the motor. if you have a belt pulley like this. get the belt and hold it together so you have a loop at the end and run under the pulley so the pulley lifts up and put the belt on the motor shaft. the belt always goes under the pulley so you are lifting upwards

Jun 21, 2009 | Dryers

Not finding what you are looking for?
Dryers Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Are you a Frigidaire Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...