Question about Behringer EUROPOWER EP2500 Amplifier

2 Answers

Howto or if i can run 4 speakers off of ep2500 what settings do i use

Hi i have 2 bass bins and 2 jbl passive speakers do i run jbls off one side and bins off the other with a crossover cheers paul and can u tell me the settings i should have with the berhinger ep2500 unit to do this

Posted by on

  • 1 more comment 
  • paul bell Sep 09, 2008

    its a berhinger cpx crossover cheers paul

  • keith armiger Oct 11, 2008

    on the back of the behringer ep2500 the are flick swiches to the left do these alter the bass in any way my bass is not sharp enough all how do i run 4 speakers from a 2 channel out put please

  • keith armiger Oct 11, 2008


    1. i need to adjust the bass from the amp can this be done please

    2. how do i run bass bins and tops from only two channels please

    3. can you get me a manual for the ep2500 please

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

  1. i need to adjust the bass from the amp can this be done please
  2. how do i run bass bins and tops from only two channels please
  3. can you get me a manual for the ep2500 please

Posted on Oct 11, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 113 Answers

That would work,what type xover do you have?

Posted on Sep 09, 2008

  • oscar herrera Sep 11, 2008

    set xover for 2way use, then set tops at 250-200hz xover point,if the bins sound a little too harsh in the low mid range its best to adjust that with your eq

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can this amp be bridged mono?


Yes, connect the speakers to the red terminals only for bridge, you good to go.

Nov 28, 2013 | PS Audio GCA-250 2-Channel Amplifier

1 Answer

I bought a mixer with this model "Behringer XENYX 1204USB 12 Ch USB Mixer". And i'm planning to have a set-up of 2 electric-acoustic guitars and 3 microphone vocals. What would be the best wattage of...


Hello Sir, Hi, the amplifier best suited for it would be a Behringer also, the EP2500 would be a match, and the eurolive B815neo speakers, but this cost a lot, any amplifier and a corresponding speaker will do. for your electric guitars or acoustics the GTX30. If you will use your 15" speakers, match it with a right amplifier, you did not mention its watts rating, If your speakers are 250 watts, then buy an amplifier slightly higher that 250 watt,

Aug 19, 2010 | Behringer EUROPOWER EP2500 Amplifier

2 Answers

Speaker linking


You know, watts is a heat dissipation unit... It tells nothing about your speaker, the usage you wanna do with it, and what about the amp! Usually on proffessionnal amplifier ( i mean touring power amp) we rely 2 speakers in parallel per side of amp. It turns the amp working at 4 ohms and ifs it pushed by a good amp, and a reasonnable operator, things goes find. If amp ''clip'' it sending DC in the speakers and you actually in the way of a repair. So its now having too much power amp that usually breaks speakers, but too small amp. Check the specifications of what your amp can gives at 20hz to 20khz, both channel driven at 4 ohms. You find out that the amp you believe was sending you 500watts is giving you only 250... Thats why pro series of amp cost so much. Because they are not playing on words but giving power... Cheap series of pro amp counts wattages at 4ohms one channel driven at 1khz at 1% distortions wich is unnaceptable. 0.1% is the max acceptables. Go meet the tech at your local big touring sound contractor and ask for the real thing. You'll get the right answer and analysis of your kit...

Aug 04, 2009 | Behringer EUROPOWER EP2500 Amplifier

1 Answer

Two 4-OHM DVC AND two 4-ohm


your amp is stable at 2ohm in stereo mode . you can wire them in series or parallel. series you add up the ohms . parallel you use this (R1+R2)divided by(R1xR2)=total resistance this figures two speakers at a time to add more speakers after total repeat formula as long as you don't go below min load you are fine . in your case all speakers in parallel you would be running 0 ohms bad . in series you would be running 16 ohms stable but not even half the power of your amp. if you hook up two in parallel and two in series on one channel you are running 1.6 ohms still not stable.If i was u I would hook up two 4ohm speakers in parallel on one channel and two in parallel on the other given you a stable 2ohm per channel.
total power output per channel 1200w

Jun 20, 2009 | Behringer EUROPOWER EP2500 Amplifier

1 Answer

Behringer ep 2500


if after the pop it smells like a firecracker just went of than you fried the circit for that speaker or if it has fuses on it or ferther down the wire check them but it could be just the radio and nothin to worry about:)  a friends car does it, and it is very anoying

Jun 01, 2009 | Behringer EUROPOWER EP2500 Amplifier

3 Answers

How would i conect a ep2500 amp two 2 subs @ 4 ohms, or 8ohms


hey" i got 2 behringer 2500 amps and i have 2 peavey speaker that are 4 ohms 2000 watts eachand want to mono the amp separte,and i want to run 1 amp to each speaker so can you help me?

Nov 26, 2008 | Behringer EUROPOWER EP2500 Amplifier

1 Answer

Proper mode settings


Hi bongodboss

The user manual for this amp has good instruction on how to connect it. You can download a copy from here.

Page 9 has info about using the amp for "bi-amping" The amp is only a stereo unit, so to do a 3-way system, you will need at least 1 amp mono in bridge mode for lows, and other stereo amp for mods, and another stereo amp for highs. You could use the internal low pass filter for the bottom end, and a 2 way crossover for the mids and highs. Much simpler doing a 2 way system with composite bins for mids and highs, and subs for lows. You only need the 2 amps and use the low and high pass filters inside the EP2500. If you need anymore help on this, I am happy to talk to you more.

regards
robotek

Jul 10, 2008 | Behringer EUROPOWER EP2500 Amplifier

1 Answer

How can i do this


Hi

the crossover has 6 output and 2 inputs in stereo type! you need amplifier to this...

Thanks!

May 16, 2008 | Behringer EUROPOWER EP2500 Amplifier

2 Answers

Behringer ep 2500


sounds like you may have a phasing problem with the 4 speakers connected in series. This has the effect of cancelling the bass out. Check that you have them all wired as say "stripe" to negative terminal on the speaker. I use this as a rule of thumb to be sure there are never any phasing problems. they all(speaker boxes) need to be facing the same way for bass to propagate well. Check that you have bridging OFF and all settings to "stereo" SAny other settings you are not sure on, just ask me here :)

Jan 15, 2008 | Behringer EUROPOWER EP2500 Amplifier

4 Answers

Behringer amp


Hello pare ko.
EP2500 is a pro amp, manufacturer says that. Notorious to me.
Got 5 of these for repair. Clip is of course cause by too much
signal from source. If the amp is still clipped or on protect even w/out
signal in, time to open and do repairs inside. usually a MOSFET
inside P50N06 (50V-60A) is kaput. or MJE15033G and MJE15032G.
Now if blowing main Fuse, main txistor 2SA1943/2SC5200 maybe gone.
Read carefully the setting of your dip switches setting at the back.
This amp can drive 750 watts/ch@4 ohms.

Good Luck From Siliconchip

Nov 11, 2007 | Behringer EUROPOWER EP2500 Amplifier

Not finding what you are looking for?
Behringer EUROPOWER EP2500 Amplifier Logo

Related Topics:

233 people viewed this question

Ask a Question

Usually answered in minutes!

Top Behringer Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

4678 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

69814 Answers

Are you a Behringer Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...