Question about RCA P52937 52" Rear Projection Television

1 Answer

RCA 52 PROJECTION TV MODEL P52151WK

MADE NO NOISE JUST WENT OFF, WHEN TRYED TO TURN BACK ON JUST LOUD POPPIN NOISE? IS THE FUSE BLOWN?

Posted by on

  • DRKNGJR Jun 12, 2008

    THANK U, ANY ONE I SHOULD CALL, LIKE BEST BUY?

  • Anonymous Jun 20, 2008

    i click the remote an nothing happen tour on an the tv make click sound an back off.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 47 Answers

No , if fuse was blown you would not get the popping. How old is unit ? It sounds like your high volt splitter. common problem with rca. repair should not cost more than 250.00. you will want to have chassis number  and manu date for help
www.classtorations.com

Posted on Jun 09, 2008

  • Craig Siplin Jun 13, 2008

    Best Buy and all the big box companies do not care about service.


    I would go to the yellowbook and look under tv repair. Ask questions about min service fee and estimate/total cost, Then go to the Better Biz Bureau and weed out the crooks.


    PS: Do not tell the servicers that you tried to do it yourself.!! They will already expect you fucked it up and charge even more


    www.classtorations.com

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 52 inch rca projection hdtv when I turn it on from the back of the tv a loud piercing noise rings out what could this be from?


REPLACE THE HIGH VOLTAGE BLOCK, PART # 258512. AND RES. PART # 238958.. OR LOOK FOR A BULGING CAPASITOR ON THE MAIN BOARD AND REPLACE IT.

Mar 15, 2009 | RCA HD52W59 HDTV Projection Television

1 Answer

My 52 in rear projectiontv would not turn on


UNPLUG UR TV FIRST go to the back of ur tv on the right there should be a panal that has three screws or more this is were the power switch board is . remove it and check that there's no black marking's on it if there is that the problem
email - bfd.pete@hotmail.co.uk

Jan 14, 2009 | RCA D52W19 52" Rear Projection Television

1 Answer

RCA TV MODEL D52W25


Take the back off the TV look where the wire from the power plug enters the TV. There is a small fuse on the board where the wire plugs into. If that fuse is blown, you have a power supply problem.

Oct 21, 2008 | RCA D52W20 52" Rear Projection HDTV-Ready...

3 Answers

RCA 52-inch (rear projection) big screen television


tv worked great, turned it off one day and back on the next and the on light would not come on nor would the tv work, rear projection 52 inch rca

Jun 18, 2008 | RCA P52926 52" Rear Projection Television

2 Answers

Will not turn on


Does the set make any sounds. DOes the front green led light or flash when you try to turn it on.. if not then it could be as simple as a fuse, if it does flash then it can be many problems

Jan 06, 2008 | RCA D52W19 52" Rear Projection Television

2 Answers

Rca d52w26 makes a long whistle noise


how long? 3 seconds.. does it sound like chirping? is it comeing from back. smell anthing?

Nov 09, 2007 | RCA D52W20 52" Rear Projection HDTV-Ready...

2 Answers

P52151WK 52" projection TV, no video


Is the audio coming from the TV's internal speakers, or from an external sound system? In the 169 series chassis, if the power supply caps or secondary rectifier are bad, or if the high voltage splitter has shorted inside, the set will not run and there will be no picture or sound from the TV. If the picture is completely black but the TV still has audio, press the menu button and see if the menu comes up on the screen. If the menu is there, check your cables on the back of the TV. If you are using a cable or satellite box, the box could be bad or the video wire could be bad or loose. If you do not get the on-screen menu, then I would guess that the solder joint next to the flyback transformer that sends filament (heater) voltage up to the picture tubes has cracked, or the low value resistor in the heater circuit has opened up. If that is the case, have the set serviced by a qualified tech familiar with the 169 series chassis.

Aug 26, 2007 | Projection Televisions

1 Answer

TV will not turn on


Probably needs a new HV Splitter block, they are very difficult to replace and can usually be accessed thru the front behind the speaker grill and behind convergence board.

Mar 18, 2007 | RCA P46924 46" Rear Projection Television

2 Answers

Tv wont turn on


The loud pop was a capacitor blowing up or the high voltage transformer blew up. Very common problem.. if its the Transformer be expected to pay 250 or more to have repaired.

Aug 21, 2006 | RCA HD52W56 52" Rear Projection HDTV

1 Answer

RCA 52" Big Screen TV model;P52920BL Chassis;PTK195KB PICTURE BOWED AFTER FUSE BLOWN.


You have bad convergence IC's.. If your not experienced in troubleshooting electronics or soldering, you should have a trained tech take a gander at the set. Its not worth risking life and limb to save a few bucks, Good Luck

Jul 30, 2006 | RCA P52920BL 52" Rear Projection...

Not finding what you are looking for?
RCA P52937 52" Rear Projection Television Logo

Related Topics:

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Projection Televisions Experts

The Wyzzyrd

Level 2 Expert

83 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

Are you a RCA Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...