Question about Toshiba REGZA 42WLG66 42 in. HD-Ready LCD Television

3 Answers

Led light blinking

It will not turn on at all. LED red light is blinking

Posted by on

  • Anonymous Aug 30, 2008

    After a quick power failure (off/on) the unit will not turn back on. The DVD LED blinks with twwo or three fast blinks in a pattern.



    1. I unpluged the unit for several minutes and tried holding the power button on. No response.

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 868 Answers

First try a hard reset. Just unplug the power cord for 4 hours or more; then try again.
If the reset does not help it means the problem is hardware failure and not software. Therefore, you will need a tech who can diagnose the electrical circuits. The short circuit conditions could be in any location within the 8 or 10 sections of the tv.
Please Rate This !!

Posted on Jun 12, 2008

  • Ron Shaw
    Ron Shaw Apr 23, 2014

    Just wanted to say THANK YOU for this no cost solution that worked!

×

The exact same thing just happened on my 32" Acai television with the dvd player built-in. I'm going to turn it off now and unplug until tomorrow and hope for the best. Darn it!

Posted on Aug 04, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The remote control can also control dvd and vcr. make shore it's on the tv seting. I'm sorry if this is something you have already tried.

Posted on Aug 02, 2008

3 Suggested Answers

  • 1 Answer

SOURCE: power led blinks but no picture or sound

Had the same problem myself. Took some doing but I managed to find a service bulletin that I downloaded. The problem is with the siene module and all you need to do is unplug connector JP63A from the main board and your TV will work again.
Take the back off the TV (there are a lot of screws) and look on the left hand side of the main circuit board that is mounted in the center of the TV. You will see a small white connector that is labelled JP63A, simply unplug it. Plug the TV back in and let it reboot. That's it, should be able to watch immediately.

Posted on Mar 15, 2009

ginko
  • 19396 Answers

SOURCE: toshiba plasma 42hp95 tv will not turn on red led lights blinking

The TV is on protect mode.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

Also ensure that the fault is not coming from a faulty receiver box sending bad signal, check if you get same problem with no receiver box or dvd connected.

If that does not work, and you keep having a flashing led on front of the TV, and tv turning off by itself after a while, that indicates a fault condition.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible reasons.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , startingthe flashing light.


If you are in situation one, then theTV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

Common faults that can occur are a blown capacitor on power board, a convergence IC has blown, or a fault on Digital board.

Check also the video cable or any external connection cable, if the cable is shorting, or the connector is bad, you can get same flashing state because of the video cable.


If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

Posted on May 22, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blinking lid locked light and green sensor light on machine won't start cycle


The good ol' Whirlpool Lid Lock Flashing Light Problem - ApplianceBlog

www.applianceblog.com/.../42456-The-good-ol-Whirlpool-Lid-Lock-Fl...

Dec 11, 2013 - 10 posts - ‎3 authors
Red Lid Lock light flashing intermittently when you try to start a cycle. ... I'm going to post what SENSING does first, then you will need to locate your tech. ... start with thelid lock on and blinking, or the unit will not start and spin. FIXED Sense light on light humming noise won't start ...
8 posts
Aug 9, 2015
Whirlpool WTW4950XW not working
10 posts
Nov 2, 2013
Stacked GE washer/dryer lights Blinking doeent start at ...
5 posts
Feb 20, 2012
More results from www.applianceblog.com

Washer Sensing led (Green) on with the lid locking led (Red ...

www.shopyourway.com > Manage My Life > Questions
... this: Sensing led (Green) on, the lid locking led (Red) blinking with a clicking noise ... red led light goes off green led light stays on and the washer does not start.

Oct 27, 2015 | Washing Machines

2 Answers

My S107G is fully charged, I turn on and off transmitter on different frequencies, turn the heli on and off according to my instruction manuel, but the lights on the heli are on,the circuit board red led...


Hi,
I have similar problem with my LS-208 heli.
Helicopter leds are blinking red/green, front white led is on, and tail leds are blinking too.
Remote controller red led is on as should be but helicopter doesn't respond to controller at all.
I followed instructions above with no success.
Anyone has a suggestion?
Regards, Yaron.

Jun 12, 2012 | SYMA Toys industrial New Syma S107 Radio...

1 Answer

KV-36XBR400 won't turn on, "standby/stero" light


You are correct. You are right about the power supply and replacing with led hdtv. You will be happy with a Samsung led. Time to upgrade.

Mar 04, 2011 | Sony KV-36XBR400 36" TV

1 Answer

The front LED flashes red & blue when I turn it on. What does this mean?


LED Indicators - LaCie 2big Network
The LED indicators above the drive bays and the front LED indicate drive status and activity.
During Startup
  • Front LED – blinks red/blue until both disks are powered on, then turns solid blue.
  • Rear LEDs – blinks red/blue until corresponding disk is powered on, then turns solid blue.
NOTE: If the device is not able to initiate the boot process following disk startup, the front is solid red.
During Bootup
  • Front LED – solid blue
  • Rear LEDs – solid blue
NOTE: If a disk is failing, both the disk’s corresponding rear LED and the front LED will be solid red.
During RAID Synchronization
  • Front LED – solid red
  • Rear LEDs – The LED corresponding to the original disk will be blinking blue and the one being synchronized is blinking red
  • Once both disks are synchronized, their corresponding rear LED and the front LED will be solid blue.

Apr 06, 2010 | LaCie 2 TB 2big Triple Interface External...

1 Answer

I need the codes for the jumbo innovage control for an advent tv.


I don't see Advent TV codes in the Innovage Jumbo Remote manual.

Here are the Code Search instructions:

  1. Turn on your TV.
  2. Press and hold down the CODE SEARCH button for 3 seconds until the red LED lights up solid red.
  3. Press the TV button on the remote. The LED will blink once and then remain solid red.
  4. Press the ON/OFF button on the remote slowly and repeatedly until the TV turns off. The LED will blink once each time you press ON/OFF.
  5. Once the TV turns off, press the ENTER button to store the code. the LED light will turn off.

Oct 11, 2009 | Innovage Jumbo Remote Control

1 Answer

I have a Jumbo universal remote by Innovage and I need the programing codes for the tv. Do you have them???


To program your remote by entering a code from a manufacturer's list, follow these steps:

  1. Turn on your TV.
  2. Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
  3. Press the TV button on the remote so that the LED blinks once and then remains solid red.
  4. Enter the first set of 3-digit codes from the list. The LED will blink once every keypress. After the 3rd digit, the red LED will turn off indicating that the code was recognized for the device. If the code was not compatible, the LED will flash several times and you need to return to step 2 to try that code again or to try the next code in the list.
  5. After the LED has turned off, aim the remote at the TV and press ON/OFF. If the device turns off, you have used the correct code and the remote was successfully programed. If the device does not power off, return to step 2 and try again with the next code in the list.


To have the remote try each TV code it knows one at a time, follow these steps:
  1. Turn on your TV.
  2. Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
  3. Press the TV button on the remote so that the LED blinks once and then remains solid red.
  4. Press the ON/OFF button slowly and repeatedly until the TV turns off. The LED will blink once each time you press the ON/OFF button.
  5. Once the TV turns off, press the ENTER button to store the code and the LED will turn off.

I hope that helps.

Aug 21, 2009 | Innovage Jumbo Remote Control

2 Answers

Both of red led blinking


Try to use third party software, to reset epson counter to zero, make sure if you can that waste bin will not overflow.

try this link


http://www.fixya.com/support/t1905683-r230_photo_printer_epson_stylus_sevice

Jun 22, 2009 | Epson Stylus Photo R200 InkJet Printer

1 Answer

LRD6399SWS


LED Display gives you your display visual alerts, signal strength, and operation mode. Here is an attached link for the manual.....http://www.uniden.com/pdf/LRD6399SWSom.pdf
But to answer your question here is what the difference between the green light and the red light are:
1. X-Band Signal Indicator—A green LED lights and blinks to
indicate the presence of an X-band radar signal. The blink rate
increases as the radar source gets closer. A distinct audio alert is
also heard.
2. K-Band Indicator— An amber (orange) LED lights and blinks to
indicate the presence of a K-band radar. The blink rate increases as
the radar source gets closer. A distinct audio alert is also heard.
3. Ka-SuperWideband Signal Indicator— A yellow LED lights and
blinks to indicate the presence of a Ka-SuperWideband radar
signal. The blink rate increases as the radar source gets closer. A
distinct audio alert is also heard.
4. Laser Signal Indicator— A red LED under L lights and blinks to
indicate the presence of a laser signal. A distinct audio alert is also
heard.
5. SWS Signal Indicator— When an early warning hazard or
informational signal is detected, the yellow SWS LED begins to
blink and the amber K-band LED lights. A distinct audio alert is
also heard.
6. Power-On Indicator— A green LED under P lights to indicate
power is being supplied to the unit and the unit is turned on.
7. LED Signal Strength Meter—Four LEDs give an accurate visual
indication of the strength of radar or laser signals.
8. City Mode Indicator—A green LED under C lights to indicate
that you selected City Mode.
9. Auto Mute Indicator— A red LED under M lights to indicate that
you selected the Auto Mute feature.

Please make sure you give me a rating and I hope this helps,
cbinny1



Oct 18, 2008 | LRD6399SWS Radar Detector

1 Answer

Free Pulse


The following procedure will re-establish the communication link between the Headphones and the Wireless adapter, this is called "pairing". Before you start please make sure both the headphones and the wireless adapter are fully charged and turned off.
Note: The headphones and the wireless adapter come pre-paired from the factory.
1. Press and hold the power button on the headphones. See Figure 1.
headphone.jpg
Figure 1

2. Continue to hold the button down until the LED starts flashing red/blue in an alternating pattern. Release the button when the LED starts flashing red/blue. See Figure 2.
headphone-flash.gif
Figure 2
3. Once the headphones LED is flashing red/blue, press and hold the power button on the wireless adapter. See Figure 3.
receiver.jpg
Figure 3
4. Hold down the button until the LED starts flashing red/blue in an alternating patter. The LED will blink blue, then turn off for a few seconds then blink red/blue. Release the button when the LED starts flashing red/blue. See Figure 4.
receiver-flash.gif
Figure 4
5. Once both the headphones LED and the adapter LED is blinking red/blue, press the volume up button once on the headphones. See Figure 5.
headphone-volumeup.jpg
Figure 5
Once the headphones is paired with the adapter, the LED on the headphones will blink blue once every two seconds. See Figure 6.
headphone-flash2.gif
Figure 6
When the adapter is paired the LED will be solid blue. See Figure 7.
receiversolid.jpg
Figure 7
The adapter may continue to blink red/blue for a few seconds even after the headphones LED starting blinking blue. This is normal; the adapter may take a few additional seconds before the LED turn solid blue.
Once the headphones and the adapter are paired, it is not necessary to pair them again even if the batteries on both units are completely drained.
Additional Note: Repeated pairing will not improve the sound quality or give the headphones and the adapter a cleaner connection.

Mar 11, 2008 | Logitech FreePulse Wireless Consumer...

Not finding what you are looking for?
Toshiba REGZA 42WLG66 42 in. HD-Ready LCD Television Logo

607 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Televison & Video Experts

The Knight
The Knight

Level 3 Expert

71611 Answers

Jaime Hernandez

Level 3 Expert

2292 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Are you a Toshiba Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...