Question about Kenmore 75022 / 75024 / 75029 Gas Kitchen Range

1 Answer

Kenmore 9114554590 will not bake or broil

When bake or broil is pressed on the keypad the clock flashes and does not allow you to input a temperature. The clock just flashes once each time you try to press either the bake or broil keys. No error code is displayed. When this first started happening it would let you input a temperature but it stopped the bake cycle after several seconds and it now has digressed to only flashing. All the other function on the computer unit and stove top burners are working. Thanks for any help you can offer!

Posted by on

  • michzhao Nov 19, 2008

    kenmore oven works only on broil not bake. what is wrong? please help...

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 196 Answers

The clock/display panel is faulty. There are a few relays on the display that have to work. If the clock is just flashing once with each keypress the the relays are not functioning. The clock/diplay will need to be replaced

Posted on Jun 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Kenmore model 950 range will not broil or bake. The control board seems to work and allows me to set the temp, etc., the clock works, the control board makes noise which sounds like it always did


Most of the time, when BOTH the oven bake and broil elements don't work, it is usually caused by an open thermal circuit breaker or fuse. When did your oven stop working? After a self-clean? This is the most common cause of one of these thermal fuses opening. Usually this device is located on the back of the oven. A few of them are manually-resettable; but most of them are one-shot thermal cut-out devices (thermal fuses) which have to be replaced once they have been triggered.

Dec 28, 2014 | Kenmore Kitchen Ranges

1 Answer

My Kenmore model 790 range will not broil or bake. The control board seems to work and allows me to set the temp, etc., the clock works, the control board makes noise which sounds like it always did w


Most of the time, when BOTH the oven bake and broil elements don't work, it is usually caused by an open thermal circuit breaker or fuse. When did your oven stop working? After a self-clean? This is the most common cause of one of these thermal fuses opening. Usually this device is located on the back of the oven. A few of them are manually-resettable; but most of them are one-shot thermal cut-out devices (thermal fuses) which have to be replaced once they have been triggered.

Dec 28, 2014 | Kenmore Kitchen Ranges

1 Answer

Latch signal mismatch error


first ,check the simple .... reset both dials to off position, then reset the time bake and clock on the upper left hand side ,make sure the start stop clocks are reset , turn back on broil ,bake temperature and see if this fixed the problem,...

Aug 05, 2012 | Kenmore Kitchen Ranges

2 Answers

I have a Kenmore 790.94479801 electric range. While using the Bake function, I noticed that the broiler element was on and the oven had gotten very hot. I hit the Stop button and noticed a small puff of...


When the broil function is off, check for continuity between the broiler relay output terminals. If there is no continuity, check for an external short. If there is continuity when the broiler is supposed to be off, you need to replace or repair the board.You can get your old board repaired at appliancetimers.com.

Mar 18, 2011 | Kenmore Kitchen Ranges

1 Answer

F3 fault code when trying to heat oven above 300 degrees.


I believe that is a short in a sensor. Does it heat to the proper temperature?

Apr 25, 2009 | Kenmore 45489 / 45482 Electric Kitchen...

1 Answer

Amana Range, Electric wont bake or broil


the fact that the time keeps flashing is odd, an you set the clock?? and if so does it return to blinking again???sme stoves wont allow proper operation of oven without the clock being set.

Mar 23, 2008 | Kitchen Ranges

2 Answers

MayTag Stove Model MES5770AAW


Here are the codes for Maytag Ranges:

MAYTAG
Type "C" and "D" Clocks Range/Stove/Oven Fault Codes Failure
Code
Condition Check/Repair F1 Supervisory relay enable shorted (non-cook mode); sounds alarm and inhibits cook mode if alarm fault monitor is always active in non-cook mode, and requires removal of power until serviced. Usually a bad touch pad or clock assembly (also called the ERC). Replace touchpad or ERC F2 Bake/broil/clean temp runaway alarm; sounds alarm and resets control to non-cook mode when bake/broil/clean temp exceeds programmed limits. Usually means a stuck relay. Electric @ 525F (bake), 640F(broil), 900F(clean)

Gas @ 525F (bake), 640F(broil), 900F(clean) F3 Open temp oven temperature sensor; sounds alarm and inhibits cook mode Replace oven temperature sensor F4 Shorted temp oven temperature sensor; sounds alarm and inhibits cook mode Replace oven temperature sensor F5 Supervisory relay enable open (cook mode); sounds alarm and resets the control to non-cook mode Replace electronic range control (ERC) F5 Missing a/c line cycle detector; displays code (no audible) Unplug appliance for two minutes, should clear problem F7 Function key shorted; too hot at the clock assembly (also called the ERC) or shorted touch pad or clock assembly (also called the ERC) Replace touchpad or ERC F8 Analog/Digital supervisory; sounds alarm to non-cook mode Replace ERC F9 Door latch supervisory (door latched) Unlock door and check switches or clock assembly (also called the ERC) F0 Cancel key supervision Requires the removal of power until serviced. See qualified technician

Dec 04, 2007 | Magic Chef CGS3760 Gas Kitchen Range

1 Answer

Oven stopped 5 to 10 minutes after pressing START


sounds like a wiring problem check your power source

Nov 29, 2007 | Whirlpool RF262LXS Kitchen Range

1 Answer

Digital Control (for oven temp and clock adjustment) not working


Puzzeled, usually when there is a stuck or shorted keypad there will be an error code. First let's see if we can tell if we are in Centigrade or Ferenhiet. Press the bake and broil button together for 2 or 3 seconds. SF should appear in the display. Press the broil pad again and C or F will be displayed. Toggle to F and press start. See if that was the problem. If not try to increase the speed of the + and - keypads. Press bake and broil together for 2 seconds until SF displays. Press the + keypad increase the speed of the control. It should toggle from 1 to 5, 5 being the fastest. Press start and see if that works. If niether works..then have someone remove the keypad ribbon cable from the control board and clean the ends with an eraser. See if that solves the issue...Catriver..post back and let me know.

May 12, 2007 | GE Profile Spectra JGBP90 Gas Kitchen...

Not finding what you are looking for?
Kenmore 75022 / 75024 / 75029 Gas Kitchen Range Logo

310 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Cindy Wells

Level 3 Expert

4755 Answers

Mike Carew

Level 3 Expert

958 Answers

Are you a Kenmore Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...