Question about Frigidaire Kitchen Ranges

1 Answer

When turning the oven on to bake or broil it cuts off and beeps with a code r13 on display.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 196 Answers

I will need the make and model number of the oven before going any further. Can you please supply this information so I can assist you ?

Posted on Jun 04, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't my whirlpool double oven model# GBD 307 cut off, plus getting a F2 E0 error code


Stove will not turn off CHECK

Temperature Control Thermostat


If the oven won't turn off the oven thermostat is often the cause of the problem. The electrical contacts inside the oven thermostat can weld themselves together and then the oven won't turn off. If this happens, turn off power to the entire appliance at the household circuit breaker or fuse. The oven thermostat usually cannot be tested and must be replaced if defective.

Oven Control Board


The oven control board has a set of relays that turn on and off power to the bake and broil circuits according to the customer settings and sensor input. If the oven won't turn off it could be that one of the relays on the oven control board is shorted closed, providing voltage to the heating circuit. It can be dangerous if the oven won't turn off. Don't leave the oven unattended without turning off power to the oven.

Relay board:
Some ovens are equipped with a relay board. This circuit board has several relays which control the switching of electrical current to the oven heat source. If the oven won't turn off it may be that one or more of the relays on the relay board have failed. If this happens replace the relay board. The relays on the board are not sold separately. ALSO CHECK THE BAKE AND BROIL ELEMENT.

: I offer free advice bcuz God is so good!












24346158-rlcwkvmjohmhoaex2htic0pp-3-0.jpg

24346158-rlcwkvmjohmhoaex2htic0pp-3-2.jpg

24346158-rlcwkvmjohmhoaex2htic0pp-3-5.jpg

24346158-rlcwkvmjohmhoaex2htic0pp-3-9.jpg

24346158-rlcwkvmjohmhoaex2htic0pp-3-14.jpg

May 06, 2014 | Whirlpool Ovens

1 Answer

F5 keeps blinking and stove is beeping


hello,

This f 5 code indicate or means that the oven has detected a condition it needsto check.what u need to do to solve this problem is to apply the below step as a guild.
Press "Cancel" to clear the display and to stop the beeping sound,then try turning the oven off and on again. If you still see the "F," turn offthe power to your oven and wait five minutes before turning it on again. If youhear the beep or see the "F" when you try to bake or broil again,



If your oven still has the warranty this will be covered under this ok
Hope this is very helpful for .

Thanks for using fixya.

Jul 27, 2011 | Microwave Ovens

1 Answer

When I push the bake or broil button, it displays an "F-3" code and beeps. What is the repair for this code? Thank you John


Hi, the f-3 error code is usually for the oven temp sensor. This is the little metal rod sticking out of the back wall of the oven cavity. replace that and plug the oven back in and it should work. Hope that helps.

Jan 12, 2011 | Kenmore 30169 Electric Single Oven

2 Answers

Thermador CM301U Microwave cook smart, self clean and proof buttons all make the display light up as normal, but probe, convection, bake, broil and roast do not. I can hear the beep but nothing on the...


there are two boards in the oven and i would think that it is the one on the left called the secondary . if you remove the display panel you will find the tech sheet and this should help diag the problem . thermador does use fault code's and if any have displayed / in the tech sheet you will be able to tell whats going on or in this case what isn't .. mm hope this helps .. feed back pls .

Nov 29, 2010 | Thermador CM301U Electric Single Oven

1 Answer

The oven doesn't turn on in the bake cycle


oven doesn't come in broil but the broil should . the bake should in bake . but if it does work in self clean then your oven is ok and its the clock ( erc) that has failed . some times there is a code in the display stating the problem. but ist loks like a clock failure . **** ..

Dec 23, 2009 | Amana AGR5735QDS Gas Kitchen Range

1 Answer

Error Message F1


no your control is out and needs to be replaced. the alarm is in the control itself. most ge ovens cannot be used, will not go into the bake or broil mode

May 15, 2009 | GE Kitchen Ranges

1 Answer

Err on display when I try to set the bake temperature


Usually, when an oven won't bake, it's because the bake element is burned out. The bake element is the black, pencil- thick tube at the bottom of the oven. When the oven heats, the element glows red. This element has an expected life-span of several years. It may last for only one; it may last for many more. When the element burns out, you need to replace it.
or try doing this
1. Turn the clock selector knob to OFF
2. “Tweak” the oven control by turning the clock selector knob slightly to the left (counter clockwise). This may stop the flashing message/beeping and clear the display window.

Nov 12, 2008 | GE Profile JTP18 Electric Single Oven

1 Answer

Electrolux built in wall oven, lights and digital display work fine, fan works fine, but the oven will not heat regardless of the mode (broil, bake, convention roast, convection bake)


Hello stevefer
Welcome.

You said, Your Electrolux built in wall oven, lights and digital display work fine, fan works fine, but the oven will not heat regardless of the mode (broil, bake, convention roast, convection bake)

First,
1.What is the Model Number and the year of your wall oven?
2.Did the oven light up and display with any error codes?
3. Did you try to turn the breaker off for 5 minutes to see if this will reset the system?

Perhaps the heating element is failing and may need to be replaced.
I will be able to better assist you when you reply with this information.
Waiting your response.
Huuum

Oct 16, 2008 | Kitchen Ranges

1 Answer

Oven stopped 5 to 10 minutes after pressing START


sounds like a wiring problem check your power source

Nov 29, 2007 | Whirlpool RF262LXS Kitchen Range

Not finding what you are looking for?
Kitchen Ranges Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Ismael Rodriguez...

Level 2 Expert

162 Answers

Mike Carew

Level 3 Expert

969 Answers

Are you a Frigidaire Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...