Question about Lexmark C762 Laser Printer

1 Answer

Lexmark Colour C752 108 service printhead error

I beleive this refers to the yellow printhead. I dont have the service manual and any help would be greatly appreciated.

Thank you in advance.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 300 Answers

You are correct, Below is that section from the manual. Before you follow this, i've found in the past that the cable connector is not seated properly on the rip board, so check this first.
If you require any of the instructions on replacing the printhead or board let me know.


Yellow Printhead Lost Hsync
Check for the correct installation of the all the cables to the RIP
Board assembly and to the Printhead assembly; J2, J3, and J4 on
the RIP Board. Go to “RIP Board” on page 5-11. If the cables are
connected correctly to the RIP Board and to the Printhead
assembly, replace the following FRU:
“RIP Board” on page 4-11
If this does not fix the problem replace:
Yellow Printhead Assembly - Go to “Printheads” on page 4-33.
Note: Whenever a printhead assembly is replaced, it is necessary
to perform the “Printhead Adjustments” on page 4-1.

Posted on Jun 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Service printhead error 114.02


You are correct, Below is that section from the manual. Before you follow this, i've found in the past that the cable connector is not seated properly on the rip board, so check this first.
If you require any of the instructions on replacing the printhead or board let me know.


Yellow Printhead Lost Hsync
Check for the correct installation of the all the cables to the RIP
Board assembly and to the Printhead assembly; J2, J3, and J4 on
the RIP Board. Go to "RIP Board" on page 5-11. If the cables are
connected correctly to the RIP Board and to the Printhead
assembly, replace the following FRU:
"RIP Board" on page 4-11 If this does not fix the problem replace:
Yellow Printhead Assembly - Go to "Printheads" on page 4-33.
Note: Whenever a printhead assembly is replaced, it is necessary
to perform the "Printhead Adjustments" on page 4-1.

Feb 15, 2014 | Printers & Copiers

1 Answer

My yellows ansd greens are switched


there are a number of possible errors here.
have the machine align its printheads
then have the machine complete colour calibration ( you will need good working printheads to complete the calibrations
when this is finished have the machine print out its config pages and demo print page ( you can find how to do this in the online user manual) this is done to Isolate the printer from the fault - if The demo page and config pages are printed correctly then the error lies external to the printer ( the software printing the document)
OR
check to see if the correct printer driver is installed (to be sure uninstall then re-install) open the driver and check to see in Preferences/colour that the settings are 'let machine decide colours'
or set to adobe pdf. print out the test page from the driver and pay close attention to the windows logo at the top of the page- it should match that on the windows start screen
if you can see that the green yellows are still out of calibration then you may need to change the printheads ( CYAN/Yellow) as the error may lie internal to the printhead.
at the end of the day the fault lies most likely with the software setup or the printheads.

Jan 18, 2014 | HP Officejet Pro L7480 All-in-One...

1 Answer

Picture prints with red tint on it


Sounds like the colour cartridge is either empty or you have blocked cyan and yellow printheads. If so, refer to the user manual for instructions on how to clean the printheads. This is a common problem on any inkjet printer which isn't used regularly and is caused by ink drying in the nozzles.

Sep 11, 2011 | Kodak EasyShare Printer Dock Series 3

1 Answer

I loaded a new colour cartridge in a lexmark p4350 it gives me a code 1102 i have cleaned the heads and still it gives an error 1102


The 1102 error message is caused by a communication failure between one of the printheads (cartridges) and the All-In-One (AIO). Please refer to this article to determine and resolve the issue: 1102 Error Message on the Lexmark P4300 Series All-In-One.

Apr 13, 2011 | Lexmark P4350 All-In-One InkJet Printer

1 Answer

Error 935.15 Service Printhead error


http://csparts.com.br/csprinter/Lexmark/E360.pdf

hope this link will help u
and dont forget to rank me

Jun 09, 2010 | Lexmark E450dn Laser Printer

1 Answer

931.01 Printhead Service Error


there is a Printhead error - No first sync

Dec 21, 2008 | Lexmark X342n All-In-One Laser Printer

1 Answer

ERROR SIGNAL CODE 5 FLASHES


Error also refers to the EEPROM for the printhead. I would reset the EEPROM and see if that helps.

Printer servcie manual here and it will show you how to do it:

http://www.tradebit.com/filedetail.php/4593231-canon-pixma-ip4200-printer-service-manual

Hope that helps

Nov 03, 2008 | Canon PIXMA iP4200 InkJet Photo Printer

2 Answers

Service printhead error 108


Error Code(s) Printhead Color 

106, 111, 115, 171, 172 Cyan 
107, 112, 116, 173, 174 Magenta 
108, 113, 117, 175, 176 Yellow 
109, 110, 114, 169, 170 Black 

Power off the printer, take the Magenta cartridge out, take a lint and dust-free cloth or tissue and clean the hysinc mirror and the printerhead lens. I just did it and it took me three minutes to clean with toilet paper rolled up like a cigarette. 
My printer is back on line. The hysinc mirror and printerhead lens is in the printer not on the magenta cartridge. Reinstall the print cartridge and power on. This has happened to me before with a different color. 

here is the Lexmark c750 support link: 
http://support.lexmark.com

I hope this helps. - This is from Joey V on fixyourownprinter dot com

Oct 13, 2008 | Lexmark C752 Printer

3 Answers

Lexmark C752 108 Printhead error


They mean the respective printheads have lost the HSynch.  The first thing the we do (and have had great success with) is to clean the laser lenses.  Then check the head wiring.  The following codes apply:
106 & 110 CYAN 107 & 111 MAGENTA 108 & 112 YELLOW 109 & 113 BLACK

Jan 10, 2008 | Lexmark C752 Printer

Not finding what you are looking for?
Lexmark C762 Laser Printer Logo

1,881 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexmark Printers & Copiers Experts

Roopesh S
Roopesh S

Level 2 Expert

228 Answers

Sanath Kumar V

Level 3 Expert

684 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Are you a Lexmark Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...