Question about Vacuums

1 Answer

Brush Not turning

Kenmore Progressive upright brush not turning. This happened before
I had the manuel but can't find it now. I forgot how to get the top off
to get to the belt. It has the indents on both sides but I can't figure it out

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,673 Answers

Not sure what model you have, you didn't post the number. But you can go to http://sears.com , click on the parts link, enter your complete model number, then you may have to scroll down, but it should give you options to click on, when you do it will come up with a parts list, aso a picture breakdown. Maybe this will help.

Posted on Jun 03, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore upright Model 116 31912101 Brush doesn't turn. Little red reset pin doesn't move.


Something is jammed in it or the belt is bad.Turn it upside down.You will see 4-6 screws.Remove the screws and the plate they are holding.Now the brush is exposed.The belt hooks on to the brush and a small wheel on the other end.Remove the brush and belt.Make sure the area is free of debris.While you have it off,replace the belt.

May 16, 2011 | Kenmore 31913 Progressive Direct Drive...

1 Answer

I have a kenmore upright direct drive vacuum. The vacuum works fine in all ways except the brush just stopped working. Any ideas?


The rubber belt which drives the brush could be broken or the brush can be clogged with string and hair etc.

Jul 15, 2010 | Kenmore Progressive 35922 Bagged Upright...

1 Answer

BELTLESS BRUSH WILL NOT REVOLVE


I bought my parents the exact same model. Do you have the floor select switch "ON" for the brush? Did the overload protector switch trip? There is a little red button sticking out from the right hand side of the head. Check to see if it is pertruding past the cover. If so, push button in and it should reset.

Feb 05, 2010 | Kenmore 31912 Progressive Direct Drive...

1 Answer

The rotator brush stopped turning. it turns fine


The brush roll will only spin when your handle is not in the locked upright position, once the handle goes upright - the brushroll de-activates

Dec 22, 2009 | Kenmore Progressive Bagless Upright with...

1 Answer

Kenmore upright model number 86039259990. The


don'thave to smell, the belt just snapped in half.unplug the vacuum and try to turn the brush roller by hand,if it turns real freely the belt is broke.it should be kind of hard to turn by hand if the belt was good

Mar 04, 2009 | Kenmore Progressive Bagless Upright with...

1 Answer

Kenmore progressive Direct Drive Vacuum w/Hepa


Check the hose and dirt inlet for a blockage. Also the brush roll, check it to see if you can turn it or not by hand. If not, then something may have jammed it.

May 03, 2008 | Kenmore 31913 Progressive Direct Drive...

2 Answers

Kenmore Progressive 100


Check the brush roll ends, make sure they turn freely, if not then replace it. The belt may look ok, but they stretch after a short time and should be replaced.

Mar 24, 2008 | Kenmore 31912 Progressive Direct Drive...

2 Answers

How to take the brush out?


There should be screws on the bottom plate covering the brush roll, take those out and it should come off and then you can access the brush roll.

Feb 17, 2008 | Kenmore Progressive Bagless Upright with...

1 Answer

How do I take the brush out?


Most of these progressive drives have a bottom plate that you can take off, then you can get to the brush roll asm. There will be several screws.

Feb 17, 2008 | Kenmore 31913 Progressive Direct Drive...

Not finding what you are looking for?
Vacuums Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vacuums Experts

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18381 Answers

D. Floyd Kolb
D. Floyd Kolb

Level 3 Expert

43501 Answers

Are you a Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...