Where is preferences in kismac 0.3? - Computers & Internet

Hi.

KisMAC is ordinarily listed in Applications, like any other installed app.
If KisMAC does not appear in applications, then reinstall the program following the directions in the provided links (you may need to install XCode and SVN client separately).

To open preferences:

a. Open KisMAC.app from Applications
b. Click KisMAC->Preferences
You can also open preferences by pressing COMMAND + COMMA hotkeys at any time.

If that does not work, reinstall Kismak following directions below:

KisMAC Compilation & Installation HowTo

How to instal KisMAC in Pasv mode (useful).

If you still get troubles there may be a problem with MacOS, try uninstalling KisMAC, updating Mac OS, then install KisMAC again.

By default, it should be off when you plug your mouse in. Here are instructions on turning it on. Check this preference file and see if it is set at "0." The file may be corrupt.

1. First, you need to modify a "hidden" preference file. To show hidden files, use a free utility like OnyX.

2. Once you can see hidden files, navigate to your User preference folder and look for .GlobalPreferences.plist. Note the file has a "." in front of it to signify it's hidden.

HD > User > Library > Preferences > .GlobalPreferences.plist

3. Open that preference file with a text editor and find "com.apple.mouse.ignoreTrackpadIfMousePresent" and change the valuse from 1 to 0.

4. Log out and log back in. You should be all set to use the trackpad again.

One more Useful link : http://www.tkjune.com/2008/11/07/enabledisable-touchpad-on-new-macbook-when-mouse-is-present/

Broadcom chipsets are the best for this type of work

You need to have an alternator capable of putting out 200 amps. I would run 0, or 1/0 power wire and a 0 or 2 ground. Deep cycle batteries preferably two ran in parallel and a 2 Farad capacitor.

try to make it region free by using the steps below

1 Press power on
2 Press set-up
3 Select preferences menu
4 Press play
5 Input 251131
6 Press "Left" then "Down" button
Should show region code
7 Select region
8 Press set-up to confirm and exit.


or

Now on the remote control
3 Press set-up
4 Select preferences menu
5 Press play
6 Input 251131
7 Press "Left" then "Down" button
Should show region code menu
8 Select region free by hitting the 10/0 button, this will change the region to region free (ie 0)
9 Press set-up to confirm and exit.

or

1 Before powering on, open the lids, remove any media and leave it open so you can actually see the compartment where you place a disc.(this is how you get access to the preferences menu)
2 switch on unit from the side of the drive

Now on the remote control
3 Press set-up
4 Select preferences menu
5 Press play
6 Input 251131
7 Press "Left" then "Down" button
Should show region code menu
8 Select region free by hitting the 10/0 button, this will change the region to region free (ie 0)
9 Press set-up to confirm and exit.

go into settings and turn off the sound for when you turn it off and on.

OR

Only the step to enter the "secret menu" is different, the rest is the same as the LG8600.

It should go as follows:

1) ##program8700 (##77647268700) SEND

2) Service code: 0 0 0 0 0 0

3) Hit #3 for "network select"

4) Hit #1 for "mode preference"

5) select 1x only and press OK

6) Hit the power key to exit out of the menu.

Hope it will help you.

Colorimetre HCFR software
AVC HD 709 calibration disk
Spyder2 colorimeter (I know most prefer the Eye-One meters, but the Spyder2 was available from my job at no cost)

Here are the settings:

PS3 Blu-Ray player

Output Format (HDMI): Y Pb/Cb Pr/Cr (important!!! NOT RGB output)
BD 1080p 24hz Output (HDMI): On (this TV can reproduce video at 48hz for accurate 2:2 pulldown)
Y Pb/Cb Pr/Cr Super White (HDMI): On (not sure if this matters)

42LG50 Settings

Aspect Ratio: Set By Program (Personal Preference)
Picture Mode: Expert 1
Backlight: 50 (Personal Preference)
Contrast: 54
Brightness: 54
Sharpness: 40 (Personal Preference)
Color: 50
Tint: 0

Fresh Contrast: Off
Noise Reduction: Off
Gamma: Medium
Black Level: Low
Real Cinema: On

White Balance: Warm
Method: 10 Point IRE

10 (-3,8,-16)
20 (15,24,-21)
30 (20,36,-22)
40 (3,19,-40)
50 (8,34,-41)
60 (10,50,-20)
70 (-5,50,-8)
80 (-16,50,18
90 (-14,50,30)
100 (-22,38,21)

Red Color: -3
Red Tint: 0
Green Color: 10
Green Tint: 0
Blue Color: 14
Blue Tint: 0
Yellow Color: 0
Yellow Tint: 1
Cyan Color: -11
Cyan Tint: 0
Magenta Color: 0
Magenta Tint: -2

Take time to get used to the settings, you may think the screen looks dull at first. The truth is most people have way too much contrast on their TVs.
These settings will also work for Cable or Dish hookups, in which case you may change the Noise Reduction option to Medium to reduce signal noise.

OR....

2POINT IRE

Backlight: 65
Contrast: 55
Brightness: 45
Sharpness: 50
Color: 45
Tint: 0

Fresh Contrast: Off
Noise Reduction: Off
Gamma: Medium
Black Level: Low
Real Cinema: On

White Balance: Warm
Method: 2 Point

Red Color: 3
Red Tint: 0
Green Color: 9
Green Tint: 2
Blue Color: -1
Blue Tint: 0
Yellow Color: 6
Yellow Tint: 5
Cyan Color: -1
Cyan Tint: 1
Magenta Color: 2
Magenta Tint: -1

Press "Setup"
Scroll to "Preference" using the Left/Right arrow key
Press "138931" and a popup screen will appear

Use the Up arrow key and select 0 for a region free DVD player

Try this:

"1. Power on
2. Open disc tray

With remote control:
3. Press Setup
4. Select Preferences
5. Enter 253135
6. Press Left Arrow
7. Press Down Arrow
(you should be seeing "REGION CODE 1" now)

8. Press 10/0 to set REGION CODE to 0
9. Press Setup (and it's done!)"