Question about Bose Wave Radio

1 Answer

Schematic and parts location

I need schematic and parts location for a Bose AWR1-1W. I think there is no +5V.

Thanks in advance,
Jack C.

Posted by on

  • 4 more comments 
  • Anonymous Nov 27, 2008

    Is there anyone who sells the main power transformer for the AWR1?

  • Anonymous Nov 27, 2008

    Is there a place where the AWR1 power transformer can be bought?

  • Kingwood43 Feb 16, 2009

    Same problem here, I'm new to this site can someone tell me how to email mosfet guy to get more info from him?

  • billm0714 Feb 20, 2009

    I also need the transformer for a AW1P can anyone help?

    billm0714@yahoo.com

  • ppieklo Mar 11, 2009

    I need a schematic for the AWR1-1W to T/Shoot a no power problem.

    Asside from Bose, where might I find a schematic?



    Thanks!

  • Anonymous Mar 13, 2009

    How do I e-mail mosfet guy to get the information. I have the same issue

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Check ac coming in, then go to the rectifier and check for dc volts on the plus and minus, check voltage at 25 volt 10,0000 uf cap should have voltage present. check positive solder joint at the cap and print board.
the mosfet guy

Posted on Feb 02, 2009

  • tim Feb 11, 2009

    i have new info on these radios that most likely cure the problem email me if you want the info.

  • Poodlehead_t Jul 22, 2011

    I fixed my problem of the popping when unplugged by finding a short on an SOT-23 package. I removed it, the short was gone on the board AND the component. I checked several times and finally decided to solder the part back on. Guess what, problem is FIXED! That blows me away, but I'm happy. Not sure how long it will last so I'd like to find a replacement part if/when needed. I don't have a schematic and there is no silkscreen on the PCB so how/where can I find that info? I have the older 3 battery unit. Thank you! Pat I've never used this, but I hope to find out more about it and how I can contribute, because I love this kind of info... :)

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need wiring diagram Bose audio input cable


Bose is proprietary. You need to either order it from them or Get a meter or continuity tester and write down the pinouts and make your own.

May 11, 2013 | Bose acoustimass 5 series II Speaker

2 Answers

Hello........ looking for a schematic for Bose 501 series 3 speakers. I need to replace the fuse in line with the tweeters.... its blown & does not have a value on it (unmarked, quick blow, twin lead,...


Did you find a solution? Dunno if it's much help, but I just today picked up some 501s - Series I I think - ugly heavy brown material grilles - but with a manual! No fuses in these, but booklet recommends installing your own in-line fuse holders (!?). Specifies a BUSS AGC-3 fuse for amps under 50wpc; or a MDL-2 fuse for amps over 50 wpc. Can be placed is series with either or the two signal wires. Very strange.... Robin

May 14, 2011 | Bose 501V Speaker

1 Answer

We can not turn on or charge the Bose. Is there a way to try a new power cord to see if that is the issue?


Which model of the Wave radio is this ? If it is using a 9V battery you might want to check the pcb for some discoloration at the Q4 transistor.
If you have a meter available confirm if it is good or bad. Bose has a
problem with this transistor part# 2SC3792 that is undersized for its
purpose. This transistor provides the 5V for the IC and without the 5V
your radio will look as if it is totally dead with no display and you cannot
turn it on. Typically it is only Q4 that is shorted (0-3 ohms) between the outside (emitter and base) pins. Replacing it with the same part will
bring the radio back to life. Bose recommends a beefier part -
2SD438F-MP-E but it is very hard to obtain. I have used a 2SC2655
without any problem and it is much easier to get.

Jun 01, 2010 | Bose Wave Radio

2 Answers

I need the Bose SoundDock schematics


No, but I have repaired many without a schematic. Aside from damage, there are abiot four basic failure modes. Tony

Aug 24, 2009 | Bose SoundDock digital music system...

1 Answer

Bose Wave Radio only turns on + off using am/fm toggle button


Unfortunately, Bose does not release their parts lists or schematics, effectively creating a monopoly for parts and repairs. In fact, their web site says that the Bose factory is the only option for service or repair. They used to list a flat rate repair charge on the web site, but removed it - probably because it scared too many people. Their troubleshooting guide (below) might help, but it's very simplistic.

Before you invest in expensive factory repair on one of these trouble prone sets, you might want to investigate the new HD radios -- better sound at a MUCH lower price.

http://www.bose.com/controller?event=VIEW_STATIC_PAGE_EVENT&url=/customer_service/owners/troubleshoot/index.jsp

Jun 11, 2009 | Bose Wave Radio

1 Answer

Loud popping and static-vol ctrl has no effect on noise


Bose will not release their schematics or parts lists, effectively giving them a monopoly on repair of their units. If you check their web site, www.bose.com, you'll find that they will repair your unit for $100 or possibly give you $200 credit towards a new model. Before you take them up on either offer, you might want to check out the new lines of HD radios. Better souind quality, MUCH lower prices than a Bose.

Bill B.

Apr 20, 2009 | Bose & Wave& Music System

2 Answers

Can Bose acoustimass 3 series II run on 12v????


I have the same speakers - and, system. I have a few comments. I don't think you can do what you want. This stuff is all specfic to bose. Man, they really don't want you using anything else. Question for you, I need one of those speakers - as, one of mine broke...I would love buy it from you if you don't use them any more. Let me know. rockyruggiero@comcast.net 630-723-7391 my name is Rocky

Feb 26, 2009 | Bose Acoustimass 3 IV System

1 Answer

Bose wave radio/cd player. Power reduction.


Unfortunately, Bose does not release their parts lists or schematics, effectively creating a monopoly for parts and repairs. In fact, their web site says that the Bose factory is the only option for service or repair. They used to list a flat rate repair charge on the web site, but removed it - probably because it scared too many people. Their troubleshooting guide (below) might help, but it's very simplistic.

Before you invest in expensive factory repair on one of these trouble prone sets, you might want to investigate the new HD radios -- better sound at a MUCH lower price.

http://www.bose.com/controller?event=VIEW_STATIC_PAGE_EVENT&url=/customer_service/owners/troubleshoot/index.jsp

Jan 19, 2009 | Bose & Wave& Music System

1 Answer

3350 power connector specs


The Pin Assignment is as follows:
Pin 1,4: +5V
Pin 2,3: not connected
Shield: Ground
The AC Adaptor is specified as 5V , 4Ampere. Actually the unit draws around 2-3 Amperes.
/------\
/ 3 1 \o
\ 4 2 /
\------/
This "Image" shows the pins, when you look onto the jack at the back side of the terminal, with the terminal standing upright. The label = 5V is located left of the jack

Jan 20, 2008 | WYSE Winterm 3350SE Network Terminal

2 Answers

No power up


Considering that power is present, popping sound is caused by a faulty Q401, 5V supply for display.

Good Luck.

Dec 22, 2007 | Bose Wave Radio

Not finding what you are looking for?
Bose Wave Radio Logo

Related Topics:

1,554 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bose Audio Players & Recorders Experts

The Knight
The Knight

Level 3 Expert

72670 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Ben Armstrong

Level 2 Expert

334 Answers

Are you a Bose Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...