Question about GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

1 Answer

Dishwasher goes through cycle but then does not drain hit start or restart lights go on and nothing

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GE Master
  • 3,247 Answers

The heater is faulty - if water is still cold then heater.

Check this diagram. Item 101
But if water is warm / hot then it is the drain pump. Do you hear the controller click at end of wash?

Check this diagram for location of drain sump and pump. Might have something blocked in.

Hope this helps. Please rate the solution if helpful else post a comment so that I can help further on this.

Posted on Oct 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I restart my dishwasher


Press and hold the start button for a few seconds. The dishwasher will drain and reset

Aug 30, 2016 | Bosch Dishwashers

1 Answer

Updated details: Normal cycle keeps blinking


Have u tried unplugging it for about 2m and plug it bk in that will master reset everything like u just bought it and see how that's works out

Sep 18, 2015 | Dishwashers

1 Answer

Kitchenaid DW KUDS30FXSS Cycle starts then I hear a solenoid actuate 4 times then unit goes into cancel drain cycle


Here's a link for the repair manual for your dishwasher:
http://www.appliancerepair.net/kitchenaid-dishwasher-repair.html
Concentration should be on Chapter 2 subsection 2-3 "No Fill"
Then go to Chapter 6; subsections 6-2, 6-3, 6-3a, 6-3b, 6-3c, and 6-3h for testing procedures on relays, actuator valves, etc.

Nov 30, 2013 | KitchenAid KUDS30FXSS Builtin Dishwasher

1 Answer

Kenmore Ultra Wash Dishwasher LIghts are blinking....


I suspect for either of these units that the timer control boards are bad.

Jan 24, 2009 | Dishwashers

2 Answers

Clean light flashes constanly. Won't clear out to start new cycle


I can't get the light to clear off. I can "cancel" and it goes through the drain cycle, but when done after opening the door to reload, then trying to start, it does nothing.

Nov 15, 2008 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Maytag dishwasher


Hi kimleh.

I'm Harvey the Master Plumber.

Your question is: The dishwasher goes through the first wash cycle on a light setting and first two on a normal cycle but will not continue.The motor hums but does nothing else.It drains fine as well after the wash cycle.

Without additional info it sounds like a control problem. Must be a warranty call. If beyond warranty then you have to decide whether it's more cost effective to repare or replace it.

Feel free contact me again!
Please give me a rating here at fixya.com before you sign off
Thank you,
Harvey your Master Plumber


Sep 12, 2008 | Maytag Dishwashers

2 Answers

None of the Wash Cycles are Working


It's probably the touchpad - commonly used buttons quit working after a while. If not, then it's the electronic control board.

Mar 09, 2008 | Whirlpool 24 in. GU1500XTLS Stainless...

2 Answers

Kenmore Ultra Wash Dishwasher LIghts are blinking....


I just read this for the same problem: push sanitize, then heat and dry, sanitize, heat and dry, sanitize, heat and dry, cancel, then open and close the door. It worked. The dishwasher is running correctly even as I type this. 

Feb 11, 2008 | Kenmore 24 in. 17262 Built-in Dishwasher

1 Answer

Indesit idl 705


you may be in "flood mode". there may be a leak into the base. or your bottom base hoses may be blocked, best get someone in who is able to strip a d/w base out.

Feb 08, 2008 | Indesit 24 in. IDL700 Built-In Dishwasher

Not finding what you are looking for?
GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Dishwashers Experts

Mike

Level 3 Expert

4336 Answers

jdthefixer

Level 3 Expert

744 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a GE Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...