Question about Mitsubishi HC3000U Multimedia Projector

1 Answer

Wait time for restarting projector/

My power went out for a split second causing my projector to power down. I tried restarting right after and it wont start back up . Is there a wait period usually for the projector to cool down?? Is this why it wont restart ?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

You were right about the shut-down time. We had an older InFocus projector at work that had the cord yanked (by the presenter no less...) which cost us a near $400 in repairs. A LOT of heat is generated in these machines and proper cooling is absolutely essential to their operation.

Posted on Jun 03, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset lamp hour on lg bx327 projector


Here is a link to the manual in case yo don't have it:
http://www.projectorcentral.com/pdf/projector_manual_6082.pdf

However it doesn't include counter reset instructions that I could find!

I didn't find specific 327 instructions, but here are 3 different procedures for other units:
Turn the power off but keep pluged in. Press the buttons on the control panel in the sequence as below.
Press "Up Arrow", Press "Down Arrow", Press "Left Arrow", Press "Right Arrow", Press "Menu", Press "Enter".

Lamp time will be initialized
Posted on Mar 01, 2008
  • If you do not have a remote here is how to reset the filter time. Use the "Menu" bottun to get the "easy menu" to display. Push the down arrow until you get to "Filter Time," then push and hold the RIGHT arrow to reset the filter time. DO NOT try to reset using the "Reset" option on the easy menu, it will not work.
    Posted on Oct 02, 2008

  • SOURCE:Lamp timer on Sharp XV-Z2000 will not reset
    • I unplug my cord, waited for 5 minutes, then reconnect cord holding the power button at same time, released, then proceded with input, left arrow, enter, right arrow and depress power button again holding for 15 seconds, then released. projector warmed up showing the "0000H" on the bottom left of screen...that's how mine worked today.

  • If/when you get it to work, please post back via comment to original question.

Jan 08, 2015 | LG BX327 3D Projector

1 Answer

Infocus in15 temp and lamp indicator flashing


Hello,


In attempts to get your IN15 projector working, please try the steps below.


Disconnect AC power from the projector and wait for 10 seconds for supply to properly discharge.

While holding down the Menu, Select and Input buttons simultaneously, plug in the main AC power until

the LEDS stop flashing (approximately 7 seconds)

Jul 15, 2012 | InFocus IN15 DLP Projector

1 Answer

LP820 projector powers up and all is well. After about 40 seconds to a minute it powers down. Control panel lights are on and LCD display says restarting. It comes back on for a couple of seconds and...


It could be are any of the led's blinking. ?
The other thing is to check the bulb is seated correctly in its connector.
Try removing bulb and reinserting.
Also clean the air filters at same time to make sure they are fine.

---


Please dont forget to vote if you liked my answer


thanks

------


Feb 10, 2011 | InFocus SP-LAMP-012 Projector Lamp for...

1 Answer

I watched a movie earlier on my epson projector with my macbook. but this evening all it shows is a blue screen and I have tried very much to get it going. I think some how now my mac in not connecting to...


You may have disconnected the projector while your laptop was about to go to sleep. Try (force) restarting the computer by holding down the power button for a few seconds, wait til it shuts down, then power-up again!

Aug 14, 2010 | Apple MacBook Mac Notebook

2 Answers

PROJECTOR PROBLEM Casio XJ 31


it wasn't able to go through cooldown mode. turn it on, power down and let it go through cooldown. does the light come on at all?

May 31, 2009 | Casio XJ-S31 Projector

2 Answers

Blinking status light


Replacing the lamp with an old one was helpful for me. Good news: the projector itself not faulty. Bad news: I have two projectors with the same issue at the same time (the lamps were replaced also at the same time) after only 400 hours of running.

Apr 01, 2008 | NEC VT47 Multimedia Projector

2 Answers

Unit powers up, fan shuts down no light.


The unit could be able to sense fan operation and prevent the lamp from lighting since this could cause heat damage or even a fire if allowed to light without any cooling.
If you can see the fan, try pushing gently on the blades, left, then right, to see if the fan shaft wobbles.

Mar 16, 2008 | Hitachi PJTX100 Multimedia Projector

3 Answers

Status light blinking red


If it is a lamp error try this:
When the lamp exceeds 2100 hoursof service, the projector cannot turn on and the manu is not displayed. Do the following:
For VT670/VT470 Press the help button on the remote control for a minimum of ten seconds.

For VT570/VT47 Press and hold the power and the exit buttons on the remote control simultaneously for a minimum of ten seconds. When the lamp time clock is reset to zero, the lamp indicator goes out. Hope this helps! :]

Oct 23, 2007 | NEC VT47 Multimedia Projector

4 Answers

Won't power off when pressing power button, just goes to standby mode


With most projectors you have to press the power button twice to confirm that you want to turn it off. When you press it the first time it waits for a bit and then turns itself back on assuming you hit the power button on accident.

Jul 23, 2007 | Compaq iPAQ MP2810 Multimedia Projector

Not finding what you are looking for?
Mitsubishi HC3000U Multimedia Projector Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Office Equipment & Supplies Experts

The Knight
The Knight

Level 3 Expert

72670 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

Jaime Hernandez

Level 3 Expert

2296 Answers

Are you a Mitsubishi Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...