Question about Heating & Cooling

1 Answer

PILOT & BURNER WONT STAY ON< ABOUT 2 to 5 MINUTE THEN GOES OUT, BUT WILL RELIGHT AGAIN

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

Pilot tube is probably restricted. Try blowing it out with compressed air.

Posted on Oct 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The pilot will not stay lit after water in tank reaches desired temperature. After tank cools down pilot will relight and heat water again thyen goes out approximately 1-2 minute3s after water has been...


Hi,
Thermocouple is getting weak... the extra heat from the main burner will keep it lit but after it goes out the thermocouple will then shut down..
Replace the thermocouple...

heatman101

Apr 30, 2011 | Rheem 40 Gallon FVR NATGAS Low WATER...

1 Answer

Pilot will stay lit but burner goes out about 1 minute after it lights


Sound like the flame sensor you could scratch around on it and try again.Possibe venting issue

May 14, 2010 | Water Heaters

1 Answer

Pilot light has gone out how do i relight it?


Hi .. look at the control valve on the burner .,. there is a knob you can turn. It has markings for pilot and run, or something like that. turn the knob to pilot and push and hold it in. Light the pilot wit a long fireplace match. After the pilot is lit, wait about half a minute and relese the knob,, the lp[ilot should stay lit.

Apr 03, 2010 | Water Heaters

3 Answers

Pilot light on water heater wont stay lit


The thermocouple has failed. It is the temp probe that goes from the pilot lite burner area to the control valve. Go to your local plumbng repair shop and buy one. Most appliance parts stores have them also. Take the old one with you and they will hook you up with an exact replacement. They are not that hard to change. Usually a nut or 2 screws in the temp bulb area at the burner end and a nut that threads into the control valve.
Make sure before you install the new one that the area where it mates to the gas valve is clean. Should be about a 20 min job including clean up with replacement parts in hand.

Jan 23, 2010 | Rheem 40 Gallon FVR NATGAS Low WATER...

1 Answer

Pool heater won't stay lit


check gas pressure might be running out of pressure gas meter might be too small and heater could be overheating

Jun 03, 2009 | Teledyne Laars Pool & Spa

1 Answer

Dryer will light and heat for a minute or so then goes out and wont relight again until it sits a while-


check your vent going out through the wall and be sure its not stopped up

Apr 23, 2009 | Dryers

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts

paulcarew

Level 3 Expert

2458 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Donni Steen

Level 3 Expert

659 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...