Question about Konica Minolta Dynax 5D / Maxxum 5D Body only Digital Camera

1 Answer

Out of funcion

My KM Maxxum 5D shows error after one shot. Then I have to turn it off and shoot and turn it off again. Also, I canĀ“t see from the display what i am about to picture. Can you please tell me what might be wrong?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

This is a known issue with a fault with the charged couple device CCD.  If you contact Konica Minolta / Sony in your city they should replace it as a recall.

Posted on Nov 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Old pictures show up fine but new pictures show up very darkkk


two reasons for this are possible:
1) you changed the exposure compensation by mistake to minus something... - see below - change it again to +- zero:
Konica Minolta MAXXUM 5D Instruction Manual Exposure Compensation
old-pictures-show-up-fine-but-new-4qf1labpgcqiqwpsaxwo3k5u-3-0.jpg
2) you should have the ISO settings to auto:


old-pictures-show-up-fine-but-new-4qf1labpgcqiqwpsaxwo3k5u-3-2.jpg
Konica Minolta MAXXUM 5D Instruction Manual Camera Sensitivity iso And...

Jan 28, 2014 | Konica Minolta Dynax 5D / Maxxum 5D...

1 Answer

On my KM D5 the shutter is defect and needs to be replaced. Where can I get a new shutter


Let's assume you could find a source for a new shutter....do you have the expertise and tools to install it? I don't think so. Who told you the shutter is defective? Can they install it? If not, your camera needs to go to a service repair facility.

Feb 03, 2011 | Konica Minolta Dynax 5D / Maxxum 5D...

1 Answer

I have a konica Monota model DG-5D camera and the USB port is not recognized when I connect it to my PC. I am attempting to down load my pictures to computer and the massage reported from the PC is...


I could not find a Konica Minolta Model DG-5D camera listed on the support web pages.
I did find a "DYNAX5D/Maxxum5D" that had driver software for Windows 98/98se.
If you're using XP or later, these drivers probably won't help you though.
Can you confirm the model number?

Dec 30, 2010 | Konica Minolta Dynax 5D / Maxxum 5D Body...

2 Answers

Hi!! I inherited a Konica Dynax Maxxum 5D it takes great pictures, but I can't figure out how to get the LCD monitor to show the picture I am taking...it is on a blue screen with functions and settings,...


To see the picture you want to take on the screen, your camera needs to have a feature called "live view". I'm not sure if your camera has that feature. It's a relatively new feature on more expensive cameras. Check your owner's manual.

Nov 08, 2010 | Konica Minolta Dynax 5D / Maxxum 5D...

1 Answer

I have a Minolta Maxxum 5D which I really like. I take a lot of pictures outside with my job. I have a telephoto lens and a regular lense as well. I switch lenses a good bit depending on the shot. ...


It can occur if the contacts on the lens where they meet the contacts on the camera body need cleaning. Try a cotton swab lightly dampened with rubbing alcohol.

Aug 11, 2010 | Konica Minolta Dynax 5D / Maxxum 5D Body...

1 Answer

My Monolta Dynax 5D judders on startup, then the shake reduction display flashes then it wont take pictures or turn off. It just shows br1 in viewfinder display


It would appear from other sites and users that the anti-shake mech has failed and the cost to repair outweighs the value so I will stick with my SonyA700, sell the lenses and filters I dont need and scrap the body. Thanks for the reply.

Aug 07, 2008 | Konica Minolta Dynax 5D / Maxxum 5D...

1 Answer

Bracketing in Maxxum 5D


Hey arnelsartwor,
To set both exposure and flash bracketing you need to press the drive mode button, and then use the up/down arrows to select bracketing and then use the right/left arrows to highlight the drive mode option and then press the center button to select the desired drive mode. These instructions are on page 50 of your user manual. I hope this helps!

Sincerely,
Allan
Go Ahead. Use Us.

May 23, 2008 | Konica Minolta Dynax 5D / Maxxum 5D...

1 Answer

Konica Minolta Dynax 5D/Maxxum 5D turns itself off after first shoot


It sounds like that's the first black frame problem that is a fairly common defect with the cameras, so much so that Sony is repairing it for free, for more info, see:

http://ca.konicaminolta.com/information/20070202/01_en.html

then go to:

http://eservice.sony.com/webrma/web/index.do to set up for service.

Oct 18, 2007 | Konica Minolta Dynax 5D / Maxxum 5D...

2 Answers

Camera freezes after taking picture


Shooting in the dark here, but the basic things you should try before all else is another mem card, and new compatible batteries. sounds more like a card problem though. hope it works out

May 12, 2006 | Konica Minolta Dynax 5D / Maxxum 5D...

Not finding what you are looking for?
Konica Minolta Dynax 5D / Maxxum 5D Body only Digital Camera Logo

Related Topics:

264 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Digital Cameras Experts

kakima

Level 3 Expert

96396 Answers

Willem.
Willem.

Level 2 Expert

345 Answers

JOHN KRISP

Level 1 Expert

21 Answers

Are you a Konica Minolta Digital Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...