Question about Magic Chef CYE3005AYW Electric Dryer

1 Answer

Dryer is not coming on. It seems that the timer is good, but am questioning the fuse that is by the lint pipe. How do you get to that?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Magic Chef Master
  • 8,220 Answers

dryer is not coming on. It seems that the timer is - themobilian_0.jpgThe thermal limit/fuse is mounted on the heater. The heater can be removed easily by taking 2 screws off. Check all components on the heater for continuity. Unplug the machine. themobilian_1.jpgthemobilian_3.jpg

Posted on Nov 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dryer gets hot on the outside of machine


Clean the lint out of the pipe that goes out side, also the grate on the outside, If that dosent do it take the back off and see where the lint comes out, take that apart and clean the lint out. I have had this problem before and just recently. The dryer has a saftey fuse, when the dryer gets too hot to shut off, thats why your clothes are not drying. 1st try the pipe that goes outside including the end(outside).

Aug 15, 2012 | Kenmore 400 6942 Dryer

1 Answer

Replaced both the high limit fuse and the nonresetable fuse, and cleaned out all lint trap duct and pipe and still will not heat up.


Make sure the heater element was not open or shorted.
Check all components with wires removed to prevent ghost feed.
At least one wire anyway. If it runs but does not heat then the non re-setable fuse is fine. Usually the small limit on top of the heater housing is open. It pops open when the ducting is clogged going outside. If all of that is good and you have 220 volts going to the terminal block then the next thing to check is the timer. Find the heavy red wire on the timer. It is connected to the heater element.
Simply remove that wire (with dryer unplugged) and check from that point to any other terminal on the timer. If you cannot get a reading from any other point on the timer (while slowly turning it to all cycles) then the contact inside the timer that carry's the load from the heater element is burnt. You would need a new timer if that was the case.

Jun 08, 2012 | Kenmore Dryers

1 Answer

My dyer wont heat and timer wont move changed the thermal fuse and cleaned all the lint out of the blower box and put in new venting pipe


Make sure you have 240 going into the dryer. If one side of the breaker is tripped it is posible for the dryer to run because the motor runs on 120 volts ac. The heat uses 240 volts. Next check the heavy red wire coming out of the timer. Remove it from the timer and attach a lead from an ohm meter to that leg on the timer. See if you can get a reading from any other leg on that timer. Move the dil to various spots on the timer and keep checking for continuity. If you cannot get a reading from that terminal to any other terminal on the dryer then you have a bad timer.
I did a few homemade movies today and posted them on my youtube channel:

http://www.youtube.com/watch?v=hbez7kjzNic&list=UUKBjalPycKRmo4Mz9vRsydg&index=3&feature=plcp

http://www.youtube.com/watch?v=AoVmPvUG_7o&list=UUKBjalPycKRmo4Mz9vRsydg&index=2&feature=plcp

Mar 07, 2012 | Whirlpool Inglis IP8200 Dryer

1 Answer

Maytag Neptune Gas Dryer MDG 5500Aww Dryer runs and heats when cold, then after about 5 minutes the flame cuts off, after a few minutews, the ingiter glows red, but the flame does not come on again unless...


Hi!!

I seems like you have a plugged up filter and/or an obstruccion in the exhaust hose/pipe.

Remove and clean lint filter, also remove exhaust hose/pipe from back of dryer and remove any lint accumulated. Check also the exhaust hole in the dryer.

Don't forget to rate this post. Good Luck!!

Jul 06, 2010 | Dryers

2 Answers

Maytag performa elecric dryer blows thermal fuse after 20 loads


you need to clean out the dryer and the vent line,the air isn't moving like it should,there is a block some where and when it heats up hotter than it should it pops the thermal fuse,if you have a long run on the vent line blow it out with a leaf blower,go outside and make sure nothing is blocking the air flow,some outside vents have cages on them so animals can't climb into the vent line,good idea but now it's a lint catch,the air can't blow out and the thermal fuse pops or the dryer takes forever to dry clothes,then clean out the duct that the lint filter slides into and vac out the inside of dryer where the motor is,you shouldn't have any problems after that,clean it out at least once a year so this doesn't happen again and you won't have any dryer fires,hope this helps,good luck

Jan 20, 2010 | Maytag Dryers

1 Answer

My dryer is heating up, but the lint is not coming out..taking hours to dry small lot of clothes


first check the outdoor vent, make sure there is no restriction of the damper blades, they should flip open when the dryer is running. remove all lint build up around the hinge pivot points. in a cold climate ,if this is you, the moisture and lint become hard and coagulate and turn stiff restricting the movement of the damper or blade. make sure that the pipe joints were not connected with screws or rivets and that the joints are going in the same direction as the air flow. all joints should be made with a good quality tape.

the next question is how long is the vent run? follow the manufacturers venting instructions. if not available, the International Residential Code says that you cannot vent a dryer longer than 25 ft.

next, unplug the dryer, pull it from the wall and remove the vent pipe connector. look inside of the vent pipe and inside the dryer vent outlet collar.use a vacuum to clean it out and reconnect. make sure there are no kinks or crushed areas on the pipe. I do recommend using only aluminum flexible or rigid pipe and not plastic or foil type flex pipe. these types restrict air flow, clog much easier and are a fire hazard.
check these things and let me know. we'll go from there.

Dec 26, 2009 | Kenmore 63942 Dryer

1 Answer

Kenmore elite 62042 says it is done, but, always requires some more time and seems to be progressing towards longer drying times. the clothes are warm but still damp. started 6-12 mos. ago, 5-10 min extra...


Here are a few more things to look at:

Sometimes blower wheels will get loose in dryers. Sometimes they will get a whole lump of lint in them or you can hear a rattling noise in the dryer, this is the blower wheel, its worn out and it can cause the fuse to blow too,or it can half *** work and take fifty forever's to dry the clothes.Or it could be just that the dryer needs a good blowing out .I use a lawn blower to get all the lint out of the dryer as well as the vent pipe and vent to outside. I take the filter HOUSING out and wash it also. That is, I remove the housing and clean is good! Making sure that the dryer is properly flowing air is a good thing!

Dec 19, 2009 | Dryers

1 Answer

Kenmore 88752 - Dryer won't heat


Hi there,

We had the same problem and I pulled the unit out and discovered the dryer lint vent pipe was kinked inside the wall and full of water. It took be a full day of work but I ran a new vent pipe up into the attic and up to a static vent and now the dryer works great.

We had a service guy from Sears come out and he tested the heater strips and said they were fine and suggested I work on clearning the lint vent pipe

It worked great.

M

Mar 18, 2009 | Kenmore 88752 Top Load Stacked Washer /...

1 Answer

Auto dry not working


If there is a dryness sensor, it will be just inside the door, on the bottom right. You can clean the sensor by rubbing the metal bars with a scrubbing pad. This will remove any wax buildup from fabric softeners.
Possible reasons your clothes may still come out wet:
1. The dryer isn't tumbling the clothes.
2. The dryer isn't heating.
3. The airflow is restricted.

From your description, the third seems most likely. If your machine is the one pictured above, inside the dryer door is a plastic grate over the lint screen. Remove the lint screen. Remove the two screws on this grate (Phillips.) Use a vacuum cleaner with a crevice tool to get out as much lint as possible. Be careful to not shove any lint or debris further down into the blower wheel.
Lint can also clog up in the vent pipe. This pipe should be cleaned or replaced anually. Also, check the exhaust vent on the side of the house.

Mar 07, 2008 | Frigidaire GLGR341AS Gas Dryer

2 Answers

196 degree non resettable thermal fuse


That is the thermal fuse. It must read closed for the dryer to work. You can connect the two wires together to check the rest of the system, but don't run it with them crossed for normal drying. Many times this is an indication that the high limit switch is sticking or the duct is clogged with lint causing a high temp situation.
Post back if you have any questions.

Nov 07, 2007 | Dryers

Not finding what you are looking for?
Magic Chef CYE3005AYW Electric Dryer Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Magic Chef Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Roderick Scott
Roderick Scott

Level 2 Expert

50 Answers

Are you a Magic Chef Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...