Question about Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore elite top load washer

I have a kenmore elite top load washer, just over a year old. It has two problems. The cycle indicator button is beeping constantly, second it will get to the spin cycle and then just stop. I have to unplug it wait a few seconds and then plug it back it in in order to ge the lid unlocked to get the clothes out that are completly soaked.

Posted by on

  • Anonymous Mar 15, 2009

    My top load washer has exact problem and it display F2

    I feel less confident on these washers from Sear.

    Imy last kenmore washer last 2.5 years.

    Teriilble quality.

    Dave

  • Anonymous Mar 14, 2014

    washer ran through cycle but lid wont open. waited several minutes but lid still locked.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 240 Answers

Error code with this? f11 or f22 are control board related commucation errors.

Posted on Jun 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a top loading Kenmore elite high efficiency washer model 796.2927, 2 years old this thanksgiving is showing erroe code LE? what do i do to fix?


On most Kenmore front load washers the LE error indicates a LOCKED MOTOR ERROR. This can be caused by:

  1. Loose motor harness connection.
  2. Failed HALL SENSOR.
  3. Failed STATOR.
  4. Failed ROTOR (cracked magnet).

Nov 06, 2012 | Washing Machines

1 Answer

Hello, I have a Kenmore Elite Oasis washer model


On this washer, the dl code indicates a failed lid lock mechanism. Pressing pause/cancel should reset the controls.

You may have to unplug the unit for 20-30 minutes, then restore the power.

If that doesn't work, the only other solution would be to replace the door lock assembly.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question!!!!!!!!!!!!!!!!!!

Jun 16, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Have Kenmore Elite Catalyst Washer showing F3.


I have a top load Kenmore Gold Catalyst Cleaning Action washer that is stuck on permanent press mode. The digital display reads 8 min. and will not turn off or clear.When it is turned on the, the timer goes to 37 minutes and beeps repeatedly through all cycles. It will not clear even when I unplug it. How do I fix this annoying thing!!? Thoughts please.

Bill

May 22, 2010 | Kenmore Washing Machines

2 Answers

Kenmore Elite Catalyst Washer Keeps beeping and displays 10


I'm not sure if you've solved this already but our Kenmore Elite washer had a similar problem that got worse. It ended up being the whole touch panel had to be replaced. I was able to diagnose and replaced it myself with help from the Tech sheet that is underneath the touch panel. Our Kenmore Elite dryer also had to have this paenl replaced several years ago when it was fairly new. Hope this helps.

Sep 08, 2009 | Kenmore 3.2 cu. ft. Top Load Washer

1 Answer

Kenmore Elite won't start


The control panel (touch panel) is faulty - and must be replaced.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

May 27, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore Elite Oasis Washing machine, less the 2 years old


This symptom indicates a stuck key on the user interface control board.
Replacing this control board would most likely fix this type of problem.
The part number for the user interface for this model is 8564374.

You can order this part from SearsPartsDirect.com, RepairClinic.com, PartSelect.com etc.

The procedure for replacing this control board is shown in the images below.


Before buying any parts I suggest you access the interface ribbon and disconnect it and then connect it back and see if there is any improvement.


You might also remove the interface from the console and check the console for any stuck buttons.

Remember to unplug the washer first.


http://media.fotki.com/1_p,wkgbsdrbswtkdqwxgtqsskgwtqkq,vi/ksgtwdgrtxkrrffsdss/1/1303472/5961857/image29464img-or.jpg

http://media.fotki.com/1_p,sqrbbsbrrbwrbdtxgtqsskgwtqkq,vi/kbqtdwdswxkbswddwbg/1/1303472/5961857/image23056img-or.gif



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Mar 23, 2009 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Kenmore Oasis Elite Top Loading Washer with an F2 error


The F02 error code indicates keypad/user interface failure. Most of the time, this is caused by a problem in the keypad/user interface. It can sometimes be caused by a failed control board.You could have an intermittent problem such as a stuck key or contact. As long as the F02 is not displayed, the washer should work normally. You can continue to use it when the F02 is not displayed. It is still safe to use the washer.
Sometimes this problem is caused by a loose wiring harness connection between the keypad/user interface control board and the machine control board.
The F2 error code on this washer indicates a stuck button on the user interface control board. The procedure for accessing the control boards on this washer is shown in the image below. I recommend unplugging the washerand checking the wire harness connection from the user interface control board to the machine control board. Try unplugging the connections and then plugging them back in a few times. Make sure that they are plugged in correctly and then reassemble and test the washer. If the F2 is still displayed, then the user interface control board will need to be replaced.
CLICK ON THIS LINK TO GET THE INSTRUCTIONS HOW TO REMOVE CONTROL BOARD:--
http://media.fotki.com/1_p,wfbgkftgqtgssggxgtqsskgwtqkq,vi/gdqwksfbdxggskbksbb/1/1303472/5961857/image8028img-or.gif
You can order a new user interface control board from the Sears PartsDirect website or from----------
www.repairclinic.com
Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.



Jan 12, 2009 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

Washer full and then stops and gives a beep while flashing F 51


On Kenmore F51 means Motor RPS Failure, the motor is not spinning or the motor sensor detects a fault.First unplug the power cord for one hour or so to check if it is a jammed sensor, and see if reset.

Dec 06, 2008 | Kenmore 24032\24036 Top Load Washer

Not finding what you are looking for?
Kenmore Elite 45986 Front Load Washer Logo

396 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Jesus  Colon
Jesus Colon

Level 1 Expert

12 Answers

Fred Sops

Level 2 Expert

271 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...