Question about Maytag Neptune MAH5500B Front Load Washer

1 Answer

Won't extract water/Maytag Neptune MAH3000AWW

At the end of the wash cycle the machine will not extract the water in the spin cycle. Told it needs a new Circuit Board and WAx Motor. Can this be fixed by a do it yourselfer?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 868 Answers

To be 100 % sure ,do this ,pull the whole face panel forward (remove the 3 screws on top face panel and may have 2 more in the back of the face panel)Once youve pulled the panel forward you will see your control board facing you.Look closely at the circuit board and look for a burnt circuit (CALLED R-11) .iF YOU SEE IT BURNT ,REPLACE THE WHOLE BOARD. I HAVE A COUPLE OF BOARDS AVAILABLE AND WAX MOTORS BUT I'LL NEED THE SERIAL NUMBER FIRST. Either way the board is easy to install the wax motor is a little more difficult.
Please Rate This !!!!

Posted on Jun 09, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Neptune washer mah3000aww skips to spin cycle and wont drain


It sounds like the "repaired" main control board is still the issue with it being intermittent.

Nov 20, 2012 | Maytag Neptune Washer

1 Answer

Maytag neptune mah3000aww washer. It cycles then sits at the end of spin, does not go off. then the door will not unlock. I turn to off, push off button. it is anyones guess if it opens


Possible that the door lock is not actuated to open after the end of the cycle and could be jammed. try using a degreasing spray like WD 40 and if there is any issue with the lock.
check this link: door lock

Jul 05, 2012 | Maytag Washing Machines

1 Answer

My maytag neptune MAH3000aww washing won't go into


most common issue with these is the door lock assy. You need to remove the control panel and check the R11 resistor on the board most likely it will be burnt. This was a common issue a few years back. If the R11 resistor is burnt you need to replace the door lock AND control board or your problem will occur again.

Hope this helps _MJ_

Jan 31, 2010 | Maytag Washing Machines

1 Answer

MAH3000AWW Does not spin fast enough on spin cycle Clothes are still full of water when done.


hi there ..sounds like your appliance is not spinning at all........(a) check if your drain pump is working correctly..(simply fill water and turn to drain)..(b) possiblity that the clutch drive mechanism is badly worn and needs replaced

regards Sir Galahad

Aug 13, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

What does the max extract feature do


If the washer is removing all of the water from the washer during the spin cycle it is likely working properly. Not an expert but I believe max extract causes the washer to spin for a slightly longer period of time in order to remove more water from the clothes. We use it regularly because our clothes come out to wet otherwise.

May 03, 2009 | Maytag Neptune MAH6500A Front Load Washer

1 Answer

Maytag neptune washer MAH3000AWW


order the wax motor kit and replace parts from the internet. there are plenty of videos how to do this. it does require minor soldering and a little mechanical aptittude.

Dec 30, 2008 | Maytag Neptune Washer

1 Answer

Maytag Neptune Max Extract Quit Working


More information about the problem is needed...there are two levels of spinning..."regular" and "Max Extract" The Max setting spins the tub much faster. If you are having trouble with really wet clothes being left in the washer...haven't really been spun at all...this might have a couple of solutions. First, check the "out of balance" switch (a little plastic square with two green wires attached) located at the base of the tub on the front on my stacked unit. Because of the vibration in the tub, the wires on mine have broken twice.right at the switch. The other possibility is the main circuit board. Check out the internet for solutions/replacements.
My washer's Max setting is not working...and I don't know the reason for this...any help? Thanks...

Mar 30, 2007 | Maytag Neptune Washer

Not finding what you are looking for?
Maytag Neptune MAH5500B Front Load Washer Logo

335 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...