Question about Brother Multi-Function Center® MFC-215C All-In-One InkJet Printer

Open Question

About the eeprom 4 digits code for GB

Please It's a very urgent and important issue for me, could you please check the right eeprom code to change the language to english on the brother mfc-215c, I would like to try the solution you gave, but I'm worried about loosing the printer if I introduce the wrong digits. I tryed to call the hotline but I couldn't get in touch with them. It would be helpfull also if you can give any of the hotline numbers with the country code.

Thankyou very much for ur help.

Posted by on

5 Suggested Answers

Mix-it-up
  • 832 Answers

SOURCE: Change Language on Brother MFC-215C

So here you go:
1# Call brother hotline for info what is the 4 Digit eeprom code for England.

2# If you have the info (e.g. 0004 -> Check by help of brother hotline because I am not sure what code you need for GB!!!)
press menu then start bk copy then fourtimes arrow-up (tel.index). machine will be in maintenance mode. press 7 then 4. You will see the dutch eeprom language code. Press the 4 numbers given to you by brother hotline. You should see the 4 digits. Press start bk copy to confirm. machine will return to maintenance.
press 9 then 9 to leave the mode. machine will come up again with english language ;-)

BEWARE: IF YOU PRESS A WRONG DIGIT CODE THE MACHINE WILL BE MALFUNCTION AND CANT BE FIXED ANYMORE!

Posted on Dec 30, 2007

informatica
  • 1113 Answers

SOURCE: Re: brother MFC-215C printer

Hi - You can download the manual from the link underlined in blue below:

MFC-215CFo scanning see page 23 of the software guide:

Software Guide

Please take a moment to rate this solution & let us know if the information given was useful to you - Good Luck!

Informatica

Posted on Aug 27, 2008

jonags3
  • 83 Answers

SOURCE: change LCD language to English on Brother MFC-3240C

Gud Day!
Power on your printer. Press the menu of your printer then sect the arrow down or up to select the language menu. press ok if u have seen language then go to option select from german to english.

Please rate the solution after you have tried it so that I can assess you more on this problem.


Jonags

Posted on Dec 11, 2008

  • 526 Answers

SOURCE: MFC 215C, mfc 215c erorr 46

most likely your flush box is full of ink, the pads will need to be replaced by a service center.

Posted on Apr 20, 2009

  • 11800 Answers

SOURCE: I have a Brother MFC-215C.The yellow isnt

Replace the yellow ink cartridge and try again. If it's the same then the printing head is clogged. To clean it you must remove it from the printer. For that look at this - it has the same mechanism

Posted on Sep 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a HP 44" Z3100 and after switching and saying "Initializing, please wait" it gives error 79-04 " Help needed urgently please!!!


Firmware issue:
1. Cancel all pending/que jobs
2. Disable nesting option
3. Dis connect data cable, restart the machine.. check...
4. Up load latest firmware.( read carefully read me file before up loading the firmware)

Jan 18, 2013 | HP DesignJet 1050c InkJet Printer

1 Answer

Error ##334., its my problem


The error code ##334 represents a EEPROM check error. The manual says this means the Printed Circuit Board may need replacing, however, try this procedure.
Insert paper into machine.
1)To enter service mode press Menu, copy, #
2) Select Test Mode with the + or - keys
3) Press OK
4) Press 8, lcd shows 'Please Wait', after wait, press 3, the lcd then alternates between 3-0 (EEPROM clear), and 3-1 (Purge flag)
5) When EEPROM clear (3-0) shows in lcd, press 0, then OK, then Stop then press the OFF button.

Repeat the above from Step1 to step3
in step 4 this time reset the Purge flag by pressing 0 when 3-1 shows in the lcd, OK, Stop, Off.
If the red fault light is still blinking press Resume.

hope this helps

Sep 05, 2011 | Canon SmartBase MP730 All-In-One InkJet...

1 Answer

My 350 bizhub has error code c0096 where is the m11 connector?


Toner Suction Fan Motor (M11) Failure:



M11 connector is on the Mechanical Control Board (PWB-A),

Also check the Power Supply Unit (PU1)



Mechanical Control Board Cover

1. Remove the Upper Rear Cover.

2. Remove the Rear Cover.


3. Remove five screws [1] and the

Mechanical Control Board Cover [2].

4. Unplug the all connectors.

5. Remove five screws [3] and the

Mechanical Control Board [4].

NOTE

? When replacing the Mechanical

Control Board, be sure to replace

the EEPROM.


? When the Mechanical Control Board

has been replaced with a new one,

check the ROM version and

upgrade the firmware to the latest


If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe


Jul 01, 2011 | Printers & Copiers

1 Answer

Flashing e and 2 on the panel When it first started, it shows 1. Than after a short while, it started to run and then I can hear a sound "cluck". Then it turns into flashing e & 2 alternatively. Please...


HTML clipboard
Hi Sounds like you need to clear the EEPROM.

EEPROM stands for Electrically Erasable Programmable Read Only Memory, It's a long name for a small chip that holds bits of data code that can be rewritten and erased by an electrical charge, one byte at a time. EEPROM data cannot be selectively rewritten; the entire chip must be erased and rewritten to update its contents.

How to Clear the EEPROM:
Error Codes Canon printers MP150 MP160
CANNON Printers MP150/MP160 ERROR CODE

E2-2 No paper (ASF)
E3-3 Paper jam
E4 No ink
E5-5 The ink cartridges are not installed or not installed properly or it is a non-supported ink cartridge.
E8 Waste ink absorber is full, or platen waste ink absorber is full
E9 The connected digital camera / video camera does not support Camera Direct Printing
E14 The Ink cartridges are positioned wrongly
E15 Ink cartridge is not installed
E16 Ink remaining is unknown
E17-E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber is full or platen waste ink absorber is full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop down / Reset button.
2) When the Power LED is lit, press the Stop/Reset button twice while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset buttons (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
4) When the LED lights are green, press the Stop/Reset button the specified number of time(s) according to the function listed in the table below. (Each time the Stop/Reset button is pressed, the LED lights will change alternately orange and green, starting with orange.)

The number of times the Reset button is pressed will have this effect
LED Function Remarks

0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset procedures below.
5 times Orange Destination setting See Destination setting procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection

Good Luck!

John P Bradley Tinteiros (Ebay)

Nov 23, 2009 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

ERROR CODE E-4 0. No activity on turning ON the printer


MP150/160 resetting errors: do a EEPROM reset
E2-2 No paper (ASF)
E3-3 Paper jam
E4 No ink
E5-5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly
E8 Waste ink absorber full, or platen waste ink absorber full

E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD over current error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error




1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the LED lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)
The number of the Reset
button pressing
LED Function Remarks

0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection


If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

May 24, 2009 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

Error code 300. How fix


Do the EEPROM initialize reset;

Start with the printer OFF
1. Hold down RESUME and then hold down POWER
2. release RESUME
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses - light color - function
Number of presses - light color - function

0 presses - green - Test print (or exit service mode on i960)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses - green - EEPROM initialize
3 presses - orange - Reset waste ink counter

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

May 01, 2009 | Printers & Copiers

1 Answer

E5 light


How to clear Error Code Canon printers MP150 MP160
CANNON Printers MP150/MP160 ERROR CODE


E2-2 No paper (ASF)
E3-3 Paper jam
E4 No ink
E5-5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly
E8 Waste ink absorber full, or platen waste ink absorber full

E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the LED lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)
The number of the Reset
button pressing
LED Function Remarks

0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection


If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

Mar 25, 2009 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

Canon pixma mp160 flashing E2


Found this on our site:
How to clear Error Code Canon printers MP150 MP160
CANNON Printers MP150/MP160 ERROR CODE


E2-2 No paper (ASF)
E3-3 Paper jam
E4 No ink
E5-5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly
E8 Waste ink absorber full, or platen waste ink absorber
full

E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error





try this method:

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the LED lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED
lights alternately in
orange and green, starting with orange.)
The number of the Reset
button pressing
LED Function Remarks

0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

Nov 23, 2008 | Canon PIXMA MP160 All-In-One InkJet...

2 Answers

Change Language on Brother MFC-215C


So here you go:
1# Call brother hotline for info what is the 4 Digit eeprom code for England.

2# If you have the info (e.g. 0004 -> Check by help of brother hotline because I am not sure what code you need for GB!!!)
press menu then start bk copy then fourtimes arrow-up (tel.index). machine will be in maintenance mode. press 7 then 4. You will see the dutch eeprom language code. Press the 4 numbers given to you by brother hotline. You should see the 4 digits. Press start bk copy to confirm. machine will return to maintenance.
press 9 then 9 to leave the mode. machine will come up again with english language ;-)

BEWARE: IF YOU PRESS A WRONG DIGIT CODE THE MACHINE WILL BE MALFUNCTION AND CANT BE FIXED ANYMORE!

Dec 30, 2007 | Brother Multi-Function Center® MFC-215C...

Not finding what you are looking for?
Brother Multi-Function Center® MFC-215C All-In-One InkJet Printer Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Brother Printers & Copiers Experts

Jesus  Colon
Jesus Colon

Level 1 Expert

12 Answers

Rick Johnson
Rick Johnson

Level 2 Expert

84 Answers

John mullen

Level 2 Expert

245 Answers

Are you a Brother Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...