Question about Raymarine C120 System Pack C120 Raystar 125 Dsm300

Open Question

Dear Sir I have a Raymarine C160, when the unit boots up it will only hold power for a few seconds and then switch's off. I've had this problem Three time's now and I have to keep sending the machine back to the UK from Kenya for repairs. What can I do to solve this problem. Regards Stuart Simpson

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

6ya.com

6ya - Get Instant Help

6ya.com

Need repair answers fast Use 6ya to...

Posted on Jan 02, 2017

Ad
  • 16 Answers

SOURCE: C120

You might try downloading the latest C-Series update from Raymarine's site. It is version 4.26. You can get it on ther site here:

http://raymarine.custhelp.com/cgi-bin/raymarine.cfg/php/enduser/std_adp.php?p_faqid=1037

Even if it is identical to the software in there now, the act of actually reflashing the software may get you up and running.

Posted on Dec 30, 2007

Ad
  • 1 Answer

SOURCE: Hello! Our Raymarine A65 will not

Probably a bad printed circuit board, just had to send mine in to have it repaired. When I hit the power button, I did hear a beep, but then nothing displayed. Mine was still under warrenty, so don't know the repair cost if yours is not.

Posted on Aug 18, 2009

Testimonial: "I have return my A65 to the retailer/maintenance desk and they are in the process of repairing it. The idea they had was as you say a broken circuit. "

vanherringto
  • 1738 Answers

SOURCE: I have a Raymarine SL631

Thanks for visiting FixYa.

Although I'm not familiar with Raymarine GPS units specifically, I've had success with others. There should be a reset button on the device (usually found on the bottom or side) it will just be a small hole just large enough to place a paper clip in. If you can find it, insert a paper clip - gently press it in - and while depressed, turn the power off and back on (while still depressing the reset button with the paper clip.)

This should perform a soft reboot where you don't loose any information programmed in the unit.

If this doesn't work, contact:
RaymarineTechnical Support
Ph: (603) 881-5200 x2444.

Their telephone support center is open Monday through Friday, 8:15 AM to 5:30 PM Eastern time.

Posted on Feb 24, 2011

ercupa190
  • 12223 Answers

SOURCE: Raymarine E90 MFD pops breaker after being on for a few minutes

the control board has a SHORT Circuit isolate a) power supply is defective: filter, diode, resistor, transf ,etc test and repair use the VOM b) display can be faulty c) Syscon can be faulty. go to the repair shop and fix it.
God bless you

Posted on Jul 30, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

In Speedometer 6y5-83570-s6 there are two black wires which is ground and which goes to fuel tank?
My Raymarine E80 depth display kept freezing up (display then says "DSM connection lost"). Of course, this seems to happen more often when entering a tight shallow anchorage in Alaska's inside passage. Raymarine tech support recommended that I update the display software and then update the DSM300 sounder software. I did this to no avail. Then Raymarine told me to install a dashboard mounted toggle switch inline with the positive power input of the DSM300 module so I could do hard re-sets (turning off the system power or powering down the displays does not reset the sounder module). This I did. Now when entering a tight anchorage, the display still freezes, but at least I can do a hard re-set with the new toggle switch and have the unit back up in about 40 seconds (a life time in a tight channel with the current running, etc.). Now, Raymarine says that if I send in the DSM module to them, they will replace it with their new circuit boards that solve this chronic problem that they have known about for a long time (hello, this is a significant safety issue - why no recall?).
Don't mess with this - send your DSM300 in to Raymarine!
Bob S.

Aug 30, 2013 | Boating

1 Answer

How do you reset a Magellan 1700 GPS?
FAQ on your unit says this.

Depending on the power switch your unit was designed with follow the instructions below:

Slide Switch If your unit has a Slide power switch then slide and hold the power switch in the off position for more than 8 seconds.

Push Down Power Button If your unit has a Push Down Power Button for a Reset pin hole on the bottom or on either side of the unit. Take a pin or an end of a paperclip and insert it into the hole and push in until you feel it pop slightly, hold it for 10 seconds. Your unit will reset itself.

Reset Power Switch If your unit has a Reset Power Switch then it will have a three position power switch (Reset, Off, On), if this is the case slide the switch to the reset position and hold it for 10 seconds to perform the reset.

If that doesn't work, contact them direct. sometimes they have to install clean firmware.

MagellanGPS Technical Support Consumer Sales Customer Service

Apr 08, 2017 | Magellan Roadmate 1700

1 Answer

C80 boats heading is off by 90 degress, after the boats batterywent flat, which internalchart should I be on wassa1984 am using the kit inthe uk.
turn off the unit ,press and hold the no1 soft key ,keeping that key pressed press the power on button for 5 seconds this will force the unit to a full factory reset and reset the unit to its original
factory defalt setting

Apr 30, 2010 | Raymarine C80 GPS Receiver

1 Answer

My Raymarine C80 CHart plotter won't load.
Check to see if this is a power issue by connecting to shore power and fully charging your batteries overnight with instruments off. While still connected to shore power, with batteries fully charged, turn on C80 navigation system. If the loading screen comes on and does not reset, then try holding down the button immediately to the right of the red power button for at least 3 seconds to see if the system re-boots.

Apr 13, 2010 | Raymarine C80 GPS Receiver

1 Answer

Error code on my RC400 Raymarine GPS 0x4000091 and system is locked any ideas?
It would appear you need to perform a hardware reset.

6.2 Resetting the System
 Three types of reset are available for the Chartplotter:
• Power-On Reset: When you turn the display unit off, then on again,
the screen reverts to the chart display with all windows cleared.
• Hardware Reset: This procedure enacts a power-on reset if the unit
has entered a lock-up condition.
To perform a hardware reset, press and hold the POWER key for 9
seconds.

Hope this helps.
Good Luck!

Apr 12, 2010 | Raymarine RC400 GPS Receiver

2 Answers

Somenon put a power on password on a hp desktop DC7900 PC
Turn the unit off. If you open the unit there will be a jumper to clear the CMOS and a battery. Remove the battery and then switch the jumper as silkscreened on the board. usually there are 3 pins currently crossed are 1 and 2. switch it to 2 and 3, press the power button then hold for a few seconds. unpress the button and remove the pwoer cord. press and hold the power button again for a few seconds to clear all power. reconnect the jumper to 1 and 2. put battery in and plug and boot. password should be gone.

in some units there is a "clear password" or "cmos password" jumper. crossing this will remove the password in those units.

Feb 17, 2010 | HP Compaq DC7900 PC Desktop

2 Answers

Error code H4-01
This mean you have low temp. on heat lamp 2 program interput clear interrupt 14 print may clear this code. if not you can look at the fusing unit and reset thrmo breaker that may be pop off.

Jul 26, 2008 | Sharp AR-C160 Color Copier

4 Answers

Raytheon rl70
I've had the same problem. before replacing the antenna, try to reset the antenna by removing power to the Raystar 120. Disconnect power by either turning off all batteries or disconnecting the red wire from the antenna at the point where it enters the junction box for the chartplotter. This action effectively removes all memory from the antenna and resets it to factory settings. There is a lithianium battery in GPS antenna that holds memory data in the antenna. Disconnecting the power to the antenna for a few seconds clears the memory.

This is exactly what I did and when I turned the chartplotter back on, my Raystar 120 immediately began working again.

May 05, 2008 | Raymarine RL70CRC GPS Receiver

2 Answers

I have a Raymarine L755 chart plotter that is continuously rebooting. It shows the initial screen and holds it for about 5 seconds and then beeps, reboots and the cycle starts over.
Make absolutely sure that all of the buttons are clear (not stuck). After that, begin by unplugging any external interfaces (including the chart card) one by one to determine if one of those is the culprit.

Apr 28, 2008 | Raymarine E120 GPS Receiver

2 Answers

RayMarine sl520 constant re-boot
Double-check that the unit is getting adequate power to it (at least 10.6 V DC.

Otherwise, Raymarine is probably going to need to look at this one as the CPU in it may be defective.

Dec 04, 2007 | Raymarine SL520 GPS Receiver

Not finding what you are looking for?

View Most Popular

C120 System Pack C120 Raystar 125 Dsm300

  • Boating

Related Question

In Speedometer 6y5-83570-s6 there are two black wires which is ground and which goes to fuel tank?

  • Boating

Open Questions:

0 Answers

why does the status light not come on?

Jun 13, 2014 | Raymarine C120 System Pack C120 Raystar...

0 Answers

raymarine c120 won't display Upon pressing the red power on button, the initial "RayMarine C120 Navigation" screen comes on. Then the screen goes blank and starts over again. It never gets to the depth finder, gps, water temp, etc. screen. Checked all cables several times and voltage to unit, all ok. any help is appreciated.

Jun 23, 2013 | Raymarine C120 System Pack C120 Raystar...

0 Answers

Can't get a fix c120 raymarine Can't get a fix c120 raymarine

Dec 30, 2012 | Raymarine C120 System Pack C120 Raystar...

0 Answers

I have a C140W from Raymarine, a DSM300, and an Airmar B164 transducer (0 degree). I lose any detail and bottom readings generally over 15 mps....seems like a high end unit to not be able to read underway. Any ideas as its really frustrating!

Jul 01, 2011 | Raymarine C120 System Pack C120 Raystar...

See all Raymarine C120 System Pack C120 Raystar 125 Dsm300 Questions

Related Topics

Raymarine C120 System Pack C120 Raystar 125 Dsm300 Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

Raymarine St 4000 Wheel Drive...

Raymarine Dsm30 Digital Sounder...

Raymarine Boating

Raymarine St6002 Smartpilot...

Raymarine Linear Feedback Unit...

Top Raymarine Boating Experts

Steve
Steve

Level 3 Expert

696 Answers

David Burbee
David Burbee

Level 3 Expert

1871 Answers

The Knight
The Knight

Level 3 Expert

75147 Answers

Are you a Raymarine Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...