Question about Ovens

2 Answers

Frigidaire oven F3 fault

Keep getting this error F3. I tried unplugging for five minutes and reset clock but still get this code. What can I do to solve this problem?

Posted by on

  • 2 more comments 
  • Tony Duncan Jun 02, 2008

    please fill me in.

  • Tony Duncan Jun 03, 2008

    Model number I believe is FGF337G

  • Tony Duncan Jun 09, 2008

    anymore help here? Gave model number. Thanks.

  • Tony Duncan Jun 11, 2008

    Model number given, hae no idea how to get you in chat. Still need help.

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 725 Answers

F3 generally means an open temperature sensor send me a chat and I can help you fix it...

Posted on Jun 02, 2008

  • 1 more comment 
  • Franklin Ouchida
    Franklin Ouchida Jun 03, 2008

    if you can get me in a chat I can help you but I will need a model number

  • Franklin Ouchida
    Franklin Ouchida Jun 12, 2008

    Not the whole model number FGF337G two letter missing at the end.

    You will need to change the electronic oven control #316455410 and the sensor probe #316233900



    F3 is the electronic oven control thinking it has a shorted probe but it may be or the electronic oven control is shorted a part that controls the over probe



    you can test the probe but I always change both..





    Only two fault codes are displayed by this control - F1 or F3. Generally, F1 display implies the electronic oven control itself has detected an internal
    malfunction. F3 implies the control has detected a sensor probe failure. In either case, an alarm will accompany a displayed F1 or F3.

    Open RTD sensor probe. Note: The EOC will initially display an F1
    for this condition. The EOC thinks a runaway oven condition exists.
    2. Shorted RTD sensor probe. Note: The F3 for shorted probe should
    only occur when the oven is active or when an attempt is made to
    enter a mode.

    Check resistance at room temperature and compare to RTD sensor
    resistance chart. If resistance does not match the chart, replace RTD
    sensor probe.
    2. Check resistance at room temperature, if less than 500 ohms, replace
    RTD sensor probe

    Temperature(°F) Resistance (ohms)
    32 ± 1.9 1000 ± 4.0
    75 ± 2.5 1091 ± 5.3
    250 ± 4.4 1453 ± 8.9
    350 ± 5.4 1654 ± 10.8
    450 ± 6.9 1852 ± 13.5
    550 ± 8.2 2047 ± 15.8
    650 ± 9.6 2237 ± 18.5
    900 ± 13.6 2697 ± 24.4



    Hope this is some help? please let me know

  • Dave Benz
    Dave Benz Apr 29, 2014

    I've replaced both the oven sensor and the igniter with new parts. The oven sensor I replaced was reading open.

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Before spending cash check your fuse - if its fine, take a damp cloth and clean the sensor. If this simple solution doesn't work then try the technical stuff.

Posted on Sep 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Frigidaire oven fpcf3091lf eo90 code keeps lighting up and beeping after the power went out.how do I get it to stop I have unplugged it and waited 5 min. But will come back.


http://manuals.frigidaire.com/prodinfo_pdf/Specsheets/FPCF3091L_1011_EN.pdf

Electronic control has detected a fault or error condition. Press CANCEL to clear the display & stop beeping. Try the selected feature again. If the E or F error code repeats, remove power from appliance, wait 5 minutes and then repower appliance. Try the selected feature again. If the fault recurs, record the fault or error code and call for service.

http://manuals.frigidaire.com/prodinfo_pdf/Springfield/316902218en.pdf

http://manuals.frigidaire.com/prodinfo_pdf/Springfield/316904423.pdf

May 30, 2015 | Frigidaire Ovens

Tip

Whirlpool oven, stove and range fault codes (ERC and EOC display errors).


Here a list of Whirpool oven fault codes. The codes had been collected from different service manuals. This was a memo that I wrote for my own use. I think this can be useful to owners and technicians.

WHIRLPOOL - most models
Range/Stove and Oven Fault Codes, Common error codes.

F1 - Analog control board Failure
Disconnect for one minute - if error comes back, replace control board
F1 - Shorted control keypad
Replace keypad
F3 - Oven temperature sensor open
Replace oven temperature probe
F2 - Oven temperature sensor shorted
Replace oven temperature probe
F3 - Oven too hot
Replace oven temperature probe
F3 - Clean temperature too hot
Replace oven probe
F5 - Door latch switch fault
Test and replace the door switch.


Whirlpool with 4 Digit Failure Code:

F1 - E1 - Electronic control (flip flop)
Replace control board
F2 - E0 - Shorted control keypad
Replace keypad
F3 - E0 - Oven temperature probe open
Replace temperature probe
F3 - E1 - Oven temperature probe shorted
Replace temperature probe
F3 - E2 - Oven temp too high
Replace temperature probe
F3 - E3 - Clean temp too hot
Replace temp. probe
F5 - E0 - Check door latch
F5 - E1 - Check door latch
Replace switch if defective

WHIRLPOOL Polara models 5 digit codes:

F1 F0 - EEPROM communication error
Replace ERC
F1 E1 - EEPROM checksum error
Replace ERC
F1 E2:7 - UL A/D errors
Replace ERC
F1 E4:2 - Model ID error
Reinsert keytail.
F1 E6:0 - Latch signal mismatch error
Replace ERC
F2 E0:4 - Shorted key error
Replace keypad assembly
F2 E1:3 Keytail unplugged
reinsert the keytail
F3 E0:5 Top oven sensor open
Test and replace top probe.
F3 E1:6 Top oven shorted
Test and replace temp probe
F3 E2:9 Bake range over temperature
Test and replace temp probe
F3 E3:8 Clean range over temperature
Test and replace temp probe.
F3 E4:10 Bottom oven sensor open
Test and replace temp probe
F3 E:15 Bottom oven sensor shorted
Test and replace temp probe
F5 E0:14 Door switch errot
Test and eventually replace door lock switch
F5 E1:16 Door latch not operating
Test and eventually replace door latch
F8 E0:17 Refrigeration error
Test the cooling module.
PF Power failure - Does not indicate a fault.
PF occurs when power is disconnected.

WHIRLPOOL
Models SF3, 30'' and 24"

F2 - Oven temperature above specifications
Check 8-pin connector from temp. probe to Electronic Oven Control
F3 - Open oven temperature probe failure
Check wiring, replace oven probe if necessary
F4 - Shorted oven temperature sensor failure
Check wiring harness, replace oven temperature probe if necessary
F5 - Push button stuck or faulty
Check for binding of pushbuttons and control panel glass. If OK, replace touch panel
F6 - Electronic control logic error (timing)
Replace Electronic Range Control (ERC)
F7 - Electronic control logic error (lock motor)
Replace ERC.
F8 - Electronic control logic error
Replace ERC.

on Jan 31, 2010 | Whirlpool RBS305PDS Electric Single Oven

1 Answer

Frigidaire oven won't work. top range works fine, but digital clock and digital display stopped working which works oven, so oven also will not work f11 code


Hello steve o - Typically error code F11 indicates a shorted keypad. Try resetting the range by unplugging it or flipping the household circuit breaker off. This usually will clear most false error codes. Wait approximately ten minutes and if the error code does not clear contact a professional to move forward accurately. Most likely the EOC on the range will need replacing.

Nov 12, 2012 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

Frigidaire model FEF352CATB has a F3 error code


Hi - Typically error code F3 indicates a faulty sensor probe or wiring harness between sensor probe and EOC. Try resetting the range by unplugging it or flipping the circuit breaker off for two minutes (this usually will clear most false error codes). Turn on the range and if resetting the unit proves to be ineffective, I would recommend contacting a professional to move forward accurately.

Oct 14, 2012 | Frigidaire Ovens

1 Answer

My frigerdaire oven heats for a while about 15-30 minutes then shuts down with a beeping noise and a f3 code.


Good Afternoon Friend,

I see that your Frigidaire double oven heats up for about 15-30 minutes, then shuts down and begins beeping while showing an F3error code. The F3 states that the oven is sensing a potential runaway temperature. This is possibly a sensor issue or it could be a false error code.

I suggest giving your double oven a hard reset by cutting the power at the circuit breaker for at least 2-3 minutes.

After restoring power you will need to reset the clock. You will do this by entering in the time and pressing start.

Let the oven heat up, and if you are still receiving an F3 error code, I suggest either contacting the manufacturer or contacting your local authorized technician to diagnose your appliance. Hope this helps.

-Best Regards-
WP

Jan 27, 2012 | Frigidaire 30 in. Electric Gallery Series...

1 Answer

My built in oven AKZ 110 is showing F 03 and nothing happens when I try to tune it in to work just stays on F 03 no fan no light either


This should help any further assistance please feel free to contact me.

WHIRLPOOL
Range/Stove/Oven Fault Codes Non Y-Line
NOTE: Not valid for Y line. If there is a Y near the end of your model number, do not use this chart.
Failure
Code
Condition Check/Repair 4 Digit Failure Code F0 - E0 Analog to Digital Failure Disconnect for 30 seconds - if display re-appears - replace control F1 - E1 Safety flip flop Replace Electronic Range Control/Clock (ERC) F2 - E0 Shorted keypad Replace Electronic Range Control/Clock (ERC) F3 - E0 Oven temperature sensor or oven temperature sensor fuse opened Replace oven temperature sensor or fuse F3 - E1 Oven temperature sensor shorted Replace oven temperature sensor F3 - E2 Oven too hot Replace oven temperature sensor F3 - E3 Clean temp too hot Replace oven temperature sensor F5 - E0 F5 - E1 and E2 Check door/latch switch Replace component 2 Digit Failure Code F0 or F1 or F5 Failed transistor Replace Electronic Range Control/Clock (ERC) F2 - E0 Oven temp too high 1. Test operation of door lock on self-clean models
2. Test relay contact operation
3. High resistance in oven temperature sensor F3 Open oven temperature sensor or thermal fuse Replace oven temperature sensor or thermal fuse F4 Shorted oven temperature sensor Replace oven temperature sensor F6 Problem in time keeping circuit 1. Reset time and/or cooking operation
2. Check for proper ground F7 Stuck function switch or button on Electronic Range Control (ERC) Replace ERC (Electronic Range Control/Clock) F8 Failure Electronic Range Control (ERC) Replace ERC (Electronic Range Control/Clock) F9 Door lock circuit Check wiring and test operation of door lock switch bkg-faultcodedivider.jpg txt-gototop.jpg WHIRLPOOL
Range/Stove Oven Fault Codes, Common
Failure
Code
Condition Check/Repair Digit Failure Code2 F1 Analog to Digital Failure Disconnect for 30 seconds - if display reappears - replace control board F1 Safety flip flop Replace board F1 Shorted keypad Replace keypad F3 Oven temperature sensor opened Replace oven temperature sensor F2 Oven temperature sensor shorted Replace oven temperature sensor F3 Oven too hot Replace oven temperature sensor F3 Clean temp too hot Replace oven temperature sensor F5 Check door/latch switch Replace switch if defective 4 Digit Failure Code F1 - E1 Safety flip flop Replace board F2 - E0 Shorted keypad Replace keypad F3 - E0 Oven temperature sensor opened Replace oven temperature sensor F3 - E1 Oven temperature sensor shorted Replace oven temperature sensor F3 - E2 Oven too hot Replace oven temperature sensor F3 - E3 Clean temp too hot Replace oven temperature sensor F5 - E0 F5 - E1 and E2 Check door/latch switch Replace switch if defective

Jul 16, 2011 | Whirlpool Ovens

1 Answer

The time blinks at 12:00, there is a beeping sound, the oven does not work. It's only 2 years old.


Hi.


The beeping sound is a warning because the oven is in lock condition, or because a fault had been detected. In this last case there would be an error code or something unusual.


Push and hold the Clock button for about 10 seconds, that will reset the oven. If that does not work, then trip the circuit breaker for five minutes and hold the button again to reset.

If still no luck, then there may be a fault condition. In that case better calling the Frigidare number listed on the owners manual.

If the oven is two year old , then there may still be warranty cover on parts, one more reason to contact the manufacturer if the oven does not reset.

Try resetting the oven first.


Regards.

Mar 04, 2010 | Frigidaire FGB24S5A Gas Single Oven

1 Answer

The oven isn't working and it says FO in red letters


GE / Hotpoint / RCA
Oven Fault Codes
Display Condition Remedy
F0 & F1 Failed Thermistor Control Replace ERC
F2 Oven Temp Exceeds 590 with unlocked door High resistance in Sensor, likely a bad sensor
F3 Open Sensor circuit Open (blown) sensor fuse or bad Sensor
F4 Shorted wire or Sensor locate short and correct it
F7-A Function pad button stuck Clean and unstick
F7-B Bad Clock Replace Clock
F8 Electrical component failure Replace ERC
F9 Program with door circuit Check wiring

Frigidaire / Westinghouse / Tappan / Gibson
Oven Fault Codes
Display Condition Remedy
F0 & F1 EOC failure Replace EOC
F2 Oven over heat Defective Sensor or EOC
F3 Oven Sensor Open Replace Sensor
F4 Shorted wire or Sensor locate short and correct it
F5 EOC failure Replace EOC
F6 EOC failure Replace EOC
F7 EOC failure Replace EOC


Maytag / MAYCOR / Magic Chef / Jennair / Admiral
Oven Fault Codes
Display Condition Remedy
F0 Function key shorted or stuck button Clean and unstick button or replace Touch Pad or Clock
F1 Defective Touch Pad or Membrane Replace Touch Pad or Membrane
F2 Oven over heat defective Relay Board or (if present) or defective Sensor
F3 Oven Sensor Open Replace Sensor
F4 Shorted wire or Sensor locate short and correct it or replace Sensor
F5 Hardware, safety circuits disagree Replace Clock
F6 Missing AC (power) signal Check for proper voltage (plug, breaker, etc.)
F7 Function key shorted or stuck button Clean and unstick button or replace Touch Pad or Clock
F8 A/D Warning Replace Clock
F9 Door Lock Warning Check door lock circuit or Replace Clock


Amana / Caloric
Oven Fault Codes
Type with display - glass link ERC
Display Condition Remedy
F0 No Safety Signal Replace adapter board
F1 No Safety Signal Replace ERC
F2 Oven over heat Replace defective Sensor
F3 Oven Sensor Open Replace Sensor
F4 Shorted wire or Sensor locate short and correct it or replace Sensor
F7 Shorted Touch Panel Replace Glass Panel
F9 Door Latch Error Check latch
FF Lock Error Check switch and motor
ERC III - Relay board with separate board/push buttons
F0 Shorted Push Pad Replace Push Pad
F1 Defective ERC Replace ERC
F2 Oven over heat Replace defective Sensor
F3 Oven Sensor Open Check/Replace Sensor
F4 Shorted wire or Sensor locate short and correct it or replace Sensor
F5 Defective ERC Replace ERC
F6 Defective ERC Replace ERC
F7 Shorted or sticking button Clean button or replace touch pad
F8 Defective ERC Replace ERC
F9 Door Latch Error Check latch


The following diagnostic chart Does not apply to Whirlpool 'Y' line products. If the model number contains a Y near the end of the number, DO NOT use this chart.
Whirlpool / KitchenAid / Roper
Oven Fault Codes
Ovens with 4 digit displays
Display Condition Remedy
F0-E0 Analog to Digital failure Disconnect panel for 30 seconds. if error re-appears then replace control
F1-E1 Defective ERC Replace ERC
F2-E0 Shorted Keypad Replace Keypad
F3-E0 Sensor or Sensor Fuse Open Replace Sensor or Fuse
F3-E1 Shorted wire or Sensor locate short and correct it or replace Sensor
F3-E2 Oven over heat Replace Sensor
F3-E3 Cleaning Temp over heat Replace Sensor
F5-E0 Door Error Check Door
F5-E1 Door Latch Check Latch
F5-E2 Door Switch Check Switch
Ovens with 2 Digit Displays
F0 Defective ERC Replace ERC
F1 Defective ERC Replace ERC
F2 Oven over heat Replace defective Sensor
F3 Oven Sensor Open Check/Replace Sensor
F4 Shorted wire or Sensor locate short and correct it or replace Sensor
F5 Defective ERC Replace ERC
F6 Problem with time keeping circuit Reset Time or cooking operation and check for proper ground
F7 Shorted or sticking button Clean button or replace ERC
F8 Defective ERC Replace ERC
F9 Door Latch Error Check latch and latch circuit

Dec 18, 2009 | Ovens

1 Answer

Fault code 01 what is it / how to correct?


HI. Essentially, this code will indicate that there is a serious issue with the main control board. Try to reset this board. This can be done, by shutting off the power for five minutes. You can unplug, or shutdown the appropriate circuit breaker for this length of time. Once the five minutes have passed, simply, re- introduce power to the unit, and try to operate normally. If the error code returns, after the reset, kindly replace the damaged main circuit board.

F-1 Board failure. Replace control board (also called ERC or clock).

Dec 09, 2009 | Whirlpool Ovens

1 Answer

F9 reset, no heat and door wont lock for cleaning. no heat for regular oven either


Hi. The unit is programmed to not operate,or heat, when there is a serious fault within the door latch assembly. This F-9 code, represents a failed door latch assembly. This device must be replaced. Once replaced, the unit will operate correctly.

NOTE_ Try to reset the mechanism. This can be done by shutting down the power, or unplugging for five minutes. Once the five minutes have passed, simply, re-introduce power to the unit, and observe. if the error code returns, replace the door latch assembly.

Dec 09, 2009 | Amana AOCS3040SS Electric Single Oven

Not finding what you are looking for?

Open Questions:

Ovens Logo

Related Topics:

1,242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ovens Experts

William Miller
William Miller

Level 3 Expert

8820 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you an Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...