Question about Fisher and Paykel Washing Machines

1 Answer

Fisher Paykel Model IW812. Service Code 37 is appearing, what does this mean?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 343 Answers

Error code 37 is pump blocked (or faulty) 'No change in water level.' Most likely you have a blocked or faulty pump motor (Not uncommon with F&P)
Thw pump motor is accessable from under the machine.
NOTE.. The machine must be empty before attempting this job.
TIP.. Lean machine back against the wall to contain the last of the water.
Make sure the 'latch' is unclipped to remove the pump motor. Turn anticlockwise to remove
Remove wires..
Check that the drain hole has nothing to prevent the impeller from turning.
Check that the pump motor turns freely..
Blow through the drain hose (from the basin end) to make sure there is no blockage..
Replace in reverse order..
If the problem persists you may need a new pump motor. These are normally checked for resistance. F&P say to replace if less than 33 ohm.
Good luck....Nomess

Posted on Oct 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is error code 130 fisher & Paykel intuitive eco IW812 ?


the R.P.S or rotory postition sensor is faulty or the connections are corroded

Jun 29, 2014 | Fisher and Paykel IWL12 Top Load Washer

2 Answers

Code 37 -


Hi,

To my knowledge, Error Code 37 on a Fisher & Paykel machine refers to "drain fault" which could either mean that the drain valve will not open or that the drain pump will not run. The easiest user intervention that could be performed is to check for any blockage/clog at the drain filter, drain pipe, drain pump impeller and drain valve.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Jul 16, 2008 | Fisher and Paykel Fisher Paykel Intuitive...

1 Answer

My washing machine IW812 has fault code 37.Could explain what that is please?


pump block error remove pump check foranything blocking or jamming it it that fails replace pump

Nov 07, 2011 | Fisher and Paykel Fisher Paykel Intuitive...

1 Answer

Fisher and Paykel iw812 had code 37, pump would run, water would drain, but a burning smell came through. Washing machine then started smoking from what I assume was the pump, then tripped out. Now there...


If it had code 37 why did you keep running it? Error codes are there for a reason. There may be no power because the pump is burnt out. Replacing the pump may restore the power if you are lucky. If power still does not come on after changing the drain pump then you are probably looking at a new control board as well. Your best thing to do is call a service company who will have a spare pump that they can try. If you buy a pump and then find it too expensive to buy the board as well, you will have wasted the money on the pump.

Dec 01, 2017 | Fisher and Paykel Washing Machines

1 Answer

Our Fisher & Paykel Washing Machine is not spinning. It gets to the spin cycle and sits there counting down. The fault code eventually said Service fault 37. What does that mean?


Emptied washer, tipped it on its side, detached drainage pipes underneath, and pulled out old fabric/lint/blockage with tweezers. Plugged in, switched on, all good.

Sep 29, 2009 | Fisher and Paykel Fisher Paykel Intuitive...

1 Answer

Screen has code 37 on it


Hi, welcome!
Code 37 is a "pump blocked error" code. Typically this code is triggered when the machine does not sense a change in the water level when called for. Check for debris caught in the pump, either in the impeller for moving water or in some cases, the external cooling fan impeller (exposed underneath the machine) gets snagged with a piece of fabric softener sheet (such as "bounce") and this will stall the pump and trigger a code 37.

I hope you find this info useful and thanks for using Fixya.

Jan 26, 2009 | Fisher and Paykel Fisher Paykel Intuitive...

1 Answer

Error code F32 for fisher paykel fridge F32 and a spanner is appearing in the display of our new Fisher Paykel fridge model # RF610ADUX. What does this mean ?


Got the same error here, called Fisher Paykel and the said it's an error related to the water line. They recommended running 3 L of water and see if code disappeared. If not, call service, they gave me a local company. Error code has disappeared, for now.

Aug 24, 2008 | Refrigerators

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

514 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...