Question about Remington Electric Pole Saw

3 Answers

The plastic female part of my Remington telescoping pole saw coupling nut split and won't hold the extension pole in place. I'm trying to find a replacement or a fix.

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Okay here is the Fix for the Remington Pole for the remington saw. Lowes has a plumbing part that will work as I just purchased it 12/2010 The part is by GENOA and its a 3/4" pvc Union and the threads match. Its Lowes part 98996 and its < $6.00

Posted on Dec 17, 2010

  • jogle297 Jun 29, 2011

    I bought a GENOVA Coupling at Lowes part 98996 & am ready to install. I have removed the chain saw, but the plug is too large to pull thru the tube & and the pole switch can't go thru the other end. I have not been able to remove the wires from the switch & I don't want cut off the plug. How did you get the pole apart? Please let me know how you replaced the coupling nut. Thanks, GlennR

  • jogle297 Jul 22, 2011

    jogle297 The GENOVA Coupling at Lowes part 68996 will not fit. The inside diameter is too small to fit over the part on the pole & the threads are square cut instead of sharp cut as on the pole saw part. I'm still looking for a solution.

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I was able to use a size 20 hose clamp around the plastic nut. It's not perfect but it works. You may need 2

Mike

Posted on Aug 17, 2014

  • Carl B
    Carl B Jul 02, 2017

    I used 2 hose clamps and seemed to do the job. It also gave me a little better leverage for loosening the nut.

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had to drill a hole through both poles and put in a screw and leave the pole extended. i also can't find the part
bill

Posted on Oct 14, 2010

  • lagator11 Nov 11, 2010

    I extended mine about half way out and then used duct tape to secure the poles. The nut had split on my saw as well, and after 2 days of searching I am unable to locate replacement parts. I didn't think about drilling and using a bolt due to the electric cord running through the poles.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a Coupling Nut for my electric pole saw


lots of luck there, if you have tried Remington, with no luck may i suggest a automotive hose clamp and a piece of inter tube.

Nov 07, 2013 | Remington Electric Pole Saw

1 Answer

Need a couplung nut for the remington RPS96 pole saw


RemingtonPower is no longer in production, The "Coupling Nut" was replaced by a "Thumb Latch" neither of these nor the entire pole assembly are available.
You might try this (no promises).
http://store.poolcenter.com/shared/StoreFront/product_detail.asp?RowID=167966&CS=poolcenter&All
Someone recommended using a hose clamp in place of the nut.
We rarely get inquiries for McCulloch or Poulan electric units. Might be worth a look.

If you care to try on your own start here:
Remington.com
http://shoppingcart.msservicecompany.com/Default.aspx

  • Type "YourModelNumber" into the "Search for your unit by Model:" window, then click search.
  • Click the “YourModelNumber” - Remington Electric Chain Saw "View Model" link.
  • Click “View Owners Manual” or "View Illustrated Parts Diagram" link.
  • Type "YourPartNumber" into the “Search for your parts by Part #:” window, then click search.

Sometimes you can find NLA parts (use part number for above) offered here:
Master Distributors
http://www.masterparts.net/remingtonelectricchainsaw.html

If you have more questions or need additional help please reply below and I will get back to you. and Good Luck. HTH
Lou
Thank you for using FixYa.

Apr 27, 2010 | Remington Electric Pole Saw

1 Answer

The plastic Pole Lock (Thumb Latch)on my Remington electric pole saw is broken. Where can I find a replacement?


RemingtonPower is no longer in production, The "Coupling Nut" was replaced by a "Thumb Latch" neither of these nor the entire pole assembly are available.
You might try this (no promises).
http://store.poolcenter.com/shared/StoreFront/product_detail.asp?RowID=167966&CS=poolcenter&All
Someone recommended using a hose clamp in place of the nut.
I think these are band-aids and eventually you will need a part that cannot be found.
We rarely get inquiries for McCulloch or Poulan electric units. Might be worth a look.

If you care to try on your own start here:
Remington.com
http://shoppingcart.msservicecompany.com/Default.aspx

  • Type "YourModelNumber" into the "Search for your unit by Model:" window, then click search.
  • Click the “YourModelNumber” - Remington Electric Chain Saw "View Model" link.
  • Click “View Owners Manual” or "View Illustrated Parts Diagram" link.
  • Type "YourPartNumber" into the “Search for your parts by Part #:” window, then click search.

Sometimes you can find NLA parts (use part number for above) offered here:
Master Distributors
http://www.masterparts.net/remingtonelectricchainsaw.html

If you have more questions or need additional help please reply below and I will get back to you. and Good Luck. HTH

Lou
Thank you for using FixYa.

Apr 17, 2010 | Remington Polesaw Wizard

1 Answer

I have a broken nut on the pole how do i fix it?


RemingtonPower is no longer in production, The "Coupling Nut" was replaced by a "Thumb Latch" neither of these nor the entire pole assembly are available.
You might try this (no promises).
http://store.poolcenter.com/shared/StoreFront/product_detail.asp?RowID=167966&CS=poolcenter&All
Someone recommended using a hose clamp in place of the nut.
I think these are band-aids and eventually you will need a part that cannot be found.
We rarely get inquiries for McCulloch or Poulan electric units. Might be worth a look.

If you care to try on your own start here:
Remington.com
http://shoppingcart.msservicecompany.com/Default.aspx
  • Type "YourModelNumber" into the "Search for your unit by Model:" window, then click search.
  • Click the “YourModelNumber” - Remington Electric Chain Saw "View Model" link.
  • Click “View Owners Manual” or "View Illustrated Parts Diagram" link.
  • Type "YourPartNumber" into the “Search for your parts by Part #:” window, then click search.

Sometimes you can find NLA parts (use part number for above) offered here:
Master Distributors
http://www.masterparts.net/remingtonelectricchainsaw.html

If you have more questions or need additional help please reply below and I will get back to you. Thank you for using FixYa and Good Luck. HTH
Lou

Apr 09, 2010 | Remington Polesaw Wizard

1 Answer

Conector from pole saw to chain saw


You provide no model number, my results may not apply to your saw,
I went here:
Remington.com
http://shoppingcart.msservicecompany.com/Default.aspx

  • Typed "RPS96" into the "Model #:" window, then clicked search.
  • Clicked the RPS96 - 8 Ft. Electric Telescoping Pole Saw "View Model" link.
  • Clicked "View Illustrated Parts Breakdown" I think you want item 7, 107551-01, Pole Saw Assembly
  • Clear the "Model #:" window; type “107551-10” (coupling nut) in the “Search for your parts by Part #:” window and click search. NLA (Internet search for “Remington 107551-01 also NLA at every site that lists it.)
  • There is also a part number "111304-01" (thumb latch) depending on the pole you have installed. It is NLA at Remington but appears to be available at "Master parts"
http://www.masterparts.net/Merchant2/merchant.mvc?Screen=PROD&Store_Code=MPD&Product_Code=111304-01
Part #: 111304-01 Price: $9.60
Description: SPECIALTY PARTS: *KIT, BRACKET (DSSP-SH3) (REM-17)


If this is also NLA, try an Internet search for "Remington YourPartNumber". eBay may be your only source.

RemingtonPower has stopped production, Replacement parts are mostly exhausted. Eventually every part will be NLA.
I worked fairly hard to provide this answer. It is a very thorough answer and it is not fair to punish me if you are unhappy with Remington. Good Luck HTH
Lou

Feb 13, 2010 | Remington Polesaw Wizard

1 Answer

I need a replacement lock on the pole of a remington 106890-02 pole saw.


Remington has closed its door. Bankrupt. If it has the round locking plastic nut, go to a swimming pool supply house.Same mechanism used of pool cleaning extension pole

Nov 19, 2009 | Remington Polesaw Wizard

1 Answer

Where can I purchase parts for the telescoping pole for my Remington Electric pole saw? I need the tightening cupling nut. Do I have to purchase the complete pole, if so, where?


IPL
http://shoppingcart.msservicecompany.com/msservice_net/product_files/RPS96/RPS96_BD.pdf
Carefully check for a number that matches something on your saw if you find what looks like the correct part.
If you find the correct do a Google search for a possible source and availability . We can do no more.

You know RemingtonPower has ceased production and replacement parts are limited to what is on hand? HTH
Lou

Oct 19, 2009 | Remington Polesaw Wizard

1 Answer

Pole Saw RPS96 - - Saw 108526-01 - - The outer clamp/nut that holds the pole at the selected length has split. I guess I could use a clamp to secure it, but I'd like to replace with the correct part. Can...


Your pole saw is at the bolttom of the page here:
http://www.desaparts.com/remington-chainsaw.html
The parts list that appears is a chainsaw. Please phone them @ 1-800-475-5660, ask for assistance and explain this little glitch. Thanks HTH
Lou

Oct 03, 2009 | Remington Electric Pole Saw

1 Answer

REMINGTON POLE CHAIN SAW


The chain has to be tensioned when replaced. You lift the chain away from the bar about halfway and the tangs that run in the bar should just almost come out of the groove. There is a screw that extends the bar near where it attaches near the sprocket. adjust that with the bar mounting nuts not quite tight till the chain is tensioned correctely.

Sep 28, 2009 | Remington Electric Pole Saw

5 Answers

I have the model 108526-01 Remington pole saw which has the round pole with a plastic compression nut (which recently broke). Can I buy the newer octagonal pole and if so, does it use the same saw mounting...


I have the sollution, had the same problem with the broken compression nut. Just use two hose clamps, one to hold the pole extended and the other clamps around compression base. Its a cheap easy fix and it work great fo me. The Real Mr.Fixit

Apr 03, 2009 | Remington Electric Pole Saw

Not finding what you are looking for?
Remington Electric Pole Saw Logo

Related Topics:

2,327 people viewed this question

Ask a Question

Usually answered in minutes!

Top Remington Garden Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Phil Walker
Phil Walker

Level 3 Expert

605 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Are you a Remington Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...