Question about Honda Maxus Prosumer MX5223 Pressure Washer

1 Answer

How to start the cleaner solution to go through the hose???

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 100 Answers

You have to make sure that you are using the correct nozzle, see this attached link for the nozzle that you should use in order to get the machine to **** chemical or detergent.

Posted on Nov 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Bissell Proheat carpet cleaner/hose for cleaning will not spray anything


My ProSeries Carpet Cleaner won't spray. What ... - Bissell

www.bissell.com > Support > Helpful Resources > FAQs

BissellLet's start by figuring out where your carpet cleaner can spray. If you have no spray at all, start below. If you have no spray at the floor but can spray from the hose, scroll down for the ... Turn the unit on after cleaning and see if water sprays to the floor now. IV. .... My ProHeat® Self-Propelled's Powerdrive isn't engaging.

Bissell Carpet Cleaner Won't Spray. Easy Repair - YouTube

? 1:48
https://www.youtube.com/watch?v=nccdrjpGp34
Dec 20, 2013 - Uploaded by Cecil Argue
You may have a bad pump, clogged hoses or a clogged heater. ... Just want to tell you that this was the perfect ...

Nov 30, 2015 | Bissell Vacuums

1 Answer

When the switch is turned on the vaccum cleaner starts running instead of,when the hose is connected. removed the earth lines from the unit and truned on the vaccum cleaner. It did the same. What might...


Dirty switch at vac where hose connects go to radio shack get some tuner cleaner spray. spray this switch and plug hose in and out a few times spray again see if this works

Feb 26, 2011 | Broan-NuTone CV554 Cyclonic Bagless...

1 Answer

Dirt devil hose is always twisted


Are you storing this pool cleaner with the hose coiled? If so, that is likely your problem. You should never coil the hose on these cleaners because it will cause problems with operation. Make sure to lay the hose flat in its original box or out of direct sunlight when you are not using it. If you start stretching it out flat during storage, it should solve the hose problem.

Feb 14, 2011 | Dirt Devil POOL CLEANER FOR ABOVE-GROUND...

1 Answer

My washer does not spray the cleaner solution as high as it did originally. The high pressure spray is fine.


If your pressure washer works like ours, it has a T connection.
A plastic hose comes off the T and goes into the bucket of cleaner
Pressure from the hose creates suction across the T and this draws cleaner into pressure hose
The plastic hose from cleaner connects to a small brass ball valve on the T
The ball valve clogs up or changes over time and cleaner will not draw up into the pressure hose.
We would replace the valve stem
I don't know if they sell the little replacement parts like they used to

Finally we had so much trouble.
We started applying our chemical with a pump-up sprayer.
For us, it was cheaper, and the work went faster.
We put one guy on the pump up sprayer
And then another guy came behind him on the washer.

Oct 25, 2010 | McCulloch FHH18A Electric Pressure Washer

1 Answer

My Legend cleaner (8 yrs. old) starts off fine but after a few minutes runs very slowly. any ideas what may be causing this?


First check the metal screen inside the fitting that connects to the pool wall. Make sure it is clean. If there is no inline screen on the feed hose then the jets inside the pool cleaner could be clogging. If there is a screen that keeps getting clogged with debris(like every couple days) then there is a problem with your pool filter or multiport valve that is allowing dirt to pass into the pool cleaner and the pool. Also it could be the back-up valve hanging up(due to a bad bearing or bushing) The back-up valve is the large canister on the feed hose about 3-6 feet above the cleaner. Check for holes in the feed hose and in the cleaner tail.

May 31, 2010 | Pentair White/Gray Legend Platinum...

2 Answers

Krauly gets tangled in the hose constantly and will not untangle


With these pool cleaners, that is almost always going to be a problem with your hose balance. To determine if your balance is correct, turn off the pump and observe the cleaner. Hose balance is correct if the cleaner's seal rests flat on the pool floor and drive tubes make a 45 degree angle with the floor. If the hose rises toward the surface at an angle greater than 45 degrees, move the weights closer to the cleaner or move the first two weights closer to each other. If the hose sags at less than a 45 degree angle, move the weights away from the Kreepy Krauly or separate the first two weights away from each other.

May 16, 2010 | Universal Kreepy Krauly In-Ground Pool...

1 Answer

MY POOL CLEANER WILL RUN FOR A FEW MINUTES, THEN STOP. SO METIMES IF I SHAKE THE HOSE IT WILL START AGAIN. ANY ANSWERS?


Hi , most pool cleaners run by the force of the sucked up water moving gears inside the cleaner .. if yours is this way, then any blockage in the cleaner or in the hose attached would restrict the flow and keep the cleaner from moving.

Apr 30, 2010 | Zodiac Baracuda G3 Automatic In Ground...

1 Answer

When i start the engine it will run at about 3000rpm .i checked the cables at the carb and the gas.what else could it be pedal


Check for vacuum leaks. Check PCV hose and other vacuum hoses. Spray carb cleaner around intake, throttle body and vacuum hoses while idling in park. If spraying anywhere causes a change in idle. that area has a vacuum leak.
Possible IAC motor dirty or defective. Remove it. Clean the IAC plunger tip and the throttle body passages with air intake/throttle body cleaner spray can. Reassemble and start vehicle.

Feb 22, 2010 | 2002 Pontiac Sunfire

1 Answer

The cleaner will run 1-2 minutes then stop. I can shake the hose & it will start again for another minute or 2. Everything looks to be in place and working. Any suggestions would be appreicated.


First, remove and check diaphragm for cuts or rips. If ok, check hoses for leaks. You can do this by holding hoses one at a time above water level while cleaner is running(or supposed to be running). If there is a leak you will hear it sucking in air. Make sure filter is ok. If a cartridge filter, remove cartridge and run without it in. If cleaner works ok without cartridge either acid wash or replace cartridge.

Jan 23, 2010 | Zodiac Baracuda G3 Automatic In Ground...

Not finding what you are looking for?
Honda Maxus Prosumer MX5223 Pressure Washer Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Garden Experts

John Trevino

Level 3 Expert

1388 Answers

JOHN LAPIER

Level 3 Expert

2428 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Are you a Honda Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...