Question about Rinnai RHFE-1004FA 38,400 BTU Energy Saver Ductless Heater - LP Gas

1 Answer

Heat shuts off, red power light blinking and number 12 blinking on the display screen.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 126 Answers

You may have had a power failure. The situation could be as simple as turning the stove off and on again. The 12 code means flame failure. Gas heater are nothing to mess around with if you don't understand them completely. Don't remove anything from the unit unless you are very sure what you're doing. A call to Rinnai is in order if the code keeps coming on. Good luck,

Tom

Posted on Oct 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Panasonic plasma tv led blinks 12


These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.
Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

Aug 24, 2016 | Panasonic TC-P46G15 Plasma TV

2 Answers

Display powers of with power up of AVC


how many blinks does the red light give in a row? This would be an error code?

The problem for 7 blinks would be an Interface board. Apparently there is a glitch in the interface board that sends signals to the television. Basically the glitch shorts out the board and the t.v wont turn on and you will see the power light blink 7 times pause then 7 more. You can replace the board with a new one and update the software on the new interface board.


If is isn't 7, let me know and I will help you out with this

thanks

Apr 26, 2008 | Sharp Aquos LC-37HV4U 37 in. LCD HDTV

1 Answer

When the TV is plugged in the screen is black,little red power light bottom right corner blink 5x then you hear the sound of power on pause then power off. This continues to repeat and no picture.


Repairing Flat Screen TV - Blacked out with blinking red light

? 12:00
https://www.youtube.com/watch?v=3GmtBthpzDk
Mar 15, 2012 - Uploaded by n1bpd
Repairing Flat Screen TV - Blacked out with blinking red light ...Capacitors are little cylinders with a flat top with an X. If they have failed the X .... picture, no sound, totally black just the red power light blinking on the corner ... hello i have a dynex dx-lcd42-09 the red light blinks as soon as i plug it in i opened ...Missing: 5x

comments on EASY HOW TO FIX SAMSUNG TV- NO POWER

https://www.youtube.com/all_comments?v=hgcmWO7mqmo


Dec 16, 2015 | Samsung 55" UN55D6420 3D LED TV Smart TV

1 Answer

I have a 56 in hdtv Panasonic tv will not come on green light flashes 20 times then goes to red. Help, on disability fixed income & cant afford to get repair or new tv. Please help, as soon as poss


Panasonic Plasma TV Repair - Understanding 14 Blink ...

? 8:35
https://www.youtube.com/watch?v=iHBIiRxhe0w
Sep 26, 2014 - Uploaded by ShopJimmy.com
Panasonic Plasma 14 Blink Code Explained with Repair Info How to ... I guess I'll try the SC board and if that does not work simply save up for a new ... The red power led was flashing 12 timespause a few seconds then flash 12 again. ... It powers up and shows the green power light is on, but there's no ...

The power light keeps flashing and the tv wont turn on - TV ...

www.tomsguide.com/answers/id.../power-light-flashing-wont-turn.html
Oct 24, 2015 - More about : power light flashing wont turn ... December 20, 2013 10:12:55 AM ... sound like it is coming on then it shuts off and the red power light flashes slowly. ... 50in Plasma tv power light is flashing 8 times and won't turn on. ...tv to come on bcause the power button keep blinking my tv will not come on.

Nov 06, 2015 | Panasonic Televison & Video

1 Answer

How do i fix/repair 6 blinks sony bravia LCD KLV-46Z450A & shutting down problem?


These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience.

May 20, 2015 | Sony Televison & Video

1 Answer

My 73" mitsubishi dlp WD-73827 turns off and has a red status light blinking. I have replaced the bulb and the heat sensor... any answer to what else could be the problem?


It is helpful to have the sequence of the blinking red light. This may help:

MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927

Page 43

3. Error Code Operational Check

Note: The TV must be in "Shut Down" and not have been switched Off, to perform the Error Code Operational

Check. When the TV is switched Off, the code automatically resets to "12" No Error.



Pressing the front panel "DEVICE" and "MENU" buttons at the same time, and holding for 5 seconds,

activates the Error Code Mode. The LED flashes denoting a two digit Error Code, or indicating no problem

has occured since the last Initalization.



Note: The front panel buttons must be used, NOT those on the Remote Control.



• The number of flashes indicates the value of the MSD (tens digit) of the Error Code.

• The flashing then pauses for approximately 1/2 second.

• The LED then flashes indicating the value of the LSD (ones digit) of the Error Code.

• The Error Code is repeated a total of 5 times.



Example: If the Error Code is "23", the LED will flash two times, pause, and then flash three times.



4. Error Codes

The Error Code designations indicating malfunction, or no malfunction, are listed below:

POWER

LED

STATUS

LED

LAMP

LED

Power

Status Condition

Off Yellow Off Low

Power Excess heat. Check Lamp Filter

Off or On Off Yellow No

change

120w usage time over 7000 Hrs.

150W usage time over 3500 Hrs.

Off Off Blinks

Yellow

Low

Power Lamp Cover open

Off Blinks

Yellow Off " Filter Cover Open

Off Off Red Stby Lamp did not turn On

Off Blinks

Red Off Low

Power Fan Stopped

Off Red Off " Circuit failure (short or DVI

connector unplugged)

Abnormal LED Indications

Error Codes "DEVICE" & "MENU"



Error Codes Description



12 No error detected

22 Recovery from Reset

32 Lamp cover is Open

34 Lamp abnormality

35 DM Fan failed (Chassis Fan)

36 Exhaust or Lamp Ballast Fan failed

37 DMD Engine Fan failed

38 Lamp temperature abnormally high. Remove Lamp to check filter.

39 DMD temperature abnormally high

41 Short is detected (Standby Power Supplies)

42 Lamp Fan failed

44 DVI cable between Format and Engine disconnected

46 DMD Temp. Sensor not detected (check DT connector))

47 DM Temperature too high

48 Engine power supply short detected

51 Speaker Drive circuit short detected

52 HDD excess temperature (V30+ & V31 only)

55 HDD Fan Stopped (V30+ & V31 onlyt)

Jul 18, 2014 | Mitsubishi WD Televison & Video

1 Answer

Battery? console has no charge when plugged into wall outlet I push power button blue LED comes on briefly , then red flashes 3 times, and the yellow LED lights up along with the health warning on the...


What color is the power light when the system shuts off?
    Red: If the power light is red, or flashing red, when the system turns off, then the system's battery needs to be charged.


    Blue: If the power light is blue when the system turns off, then there appears to be a problem with the system and it will need to be repaired.

    If the orange recharge indicator light blinks while the system is plugged in and charging, then it is likely that the battery is not installed properly.

    If you have ensured that the battery is installed properly but the orange light still blinks, check to make sure that the battery is a licensed by Nintendo. The only licensed Nintendo DSi battery will have the model number "TWL-003" (Nintendo DSi) or "UTL-003" (Nintendo DSi XL) and will display Nintendo's logo.
    Call 1-800-255-3700 if you still need help.

Jan 27, 2011 | Nintendo DSi Matte Blue Console

1 Answer

Error message


My plasma display the "error message condition 1" and red flashing light start blinking and TV screen shut down. Who can halp me to fix the problem??

Jul 03, 2008 | Fujitsu Plasmavision PDS-4221 42 in....

3 Answers

Toshiba CF30E50 TV shuts off


Best first step is: Good visual inspection = look for hot spots
on PCB, check caps in those areas + solder any/all bad connections,esp. low voltage regulator pins.Look the whole
board over with magnifier = solder,solder,solder...T.

Oct 25, 2007 | Televison & Video

Not finding what you are looking for?
Rinnai RHFE-1004FA 38,400 BTU Energy Saver Ductless Heater - LP Gas Logo

298 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rinnai Heating & Cooling Experts

paulcarew

Level 3 Expert

2458 Answers

blender719

Level 1 Expert

53 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Rinnai Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...