Question about Black & Decker Drills

1 Answer

Drill wont take a charge or operate, drill 9089 10mm type 3, 6 volt

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 30 Answers

9 times out of 10 problems like this are the result of a bad battery, in other cases it can be a bad charger. Without knowing more information I cannot give you an exact diagnosis. This is the first question I ask when approached with this issue, Has this drill been sitting for a period of time and if so, was the battery charged before it was put away? If Yes, the drill has been sitting and No, it was not charged are your answers than chances are your batteries are dead. This tool has Ni-Cd batteries that self discharge as they sit, eventually these batteries discharge until they have nothing left. In addition, if the battery is stored in a cold garage/shed will speed up this self discharge. I always tell people to think of their power tool batteries just lie a just like a car battery that dies if it sits too long without being started.
If you do not use your power tools on a regular basis it is recommended to fully charge the batteries before storing them or else they will self discharge until completely dead. Another option is the newer Lithium-Ion power tools batteries are not as temperature sensitive, have a much slower self discharge and can sit for 12-18 months before starting to loose their charge.
A replacement battery for this drill runs about $42 plus s/h and can be purchased directly from Black & Decker (1-800-4-DeWalt or www.dewaltservicenet.com) My recommendation is to purchase a new drill. For around $40 - $50 you can buy a newer upgraded model with new battery and charger.
If you think your issue may be something else, please feel free to ask. If you feel I have helped explain or resolve your issue than please rate me. Thank you

Posted on Oct 11, 2010

  • Mr Computers USA
    Mr Computers USA Nov 06, 2013

    They don't even sell battery replacements for these. What a waste of a perfectly good drill.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How long does it take to charge 18 volt battery for cd18sr type 1


Depends on whether you have a quick charger or not. One hour for quick 3 hrs for a normal charger.

Sep 12, 2016 | Drills

1 Answer

Why wont my black and decker 7.2 lithium drill take a charge ?


Did you check if the battery holds the charge? Also, you should verify the charger's output with a voltimeter.

Oct 26, 2015 | Black and Decker USA Black & Decker...

1 Answer

Ryobi manuals


YOU CAN GO TO GOOGLE AND DOWN LOAD THE MANUEL.JUST TYPE IN INSTRUCTION MANUEL ROYOBI CORDLESS DRILL 1048-67479CS LITHIUM BATATERY CB 120L YOU SHOULD BE ABLE TO DOWNLOAD THE MANUEL

Aug 12, 2014 | Ryobi Ridgid 12V Cordless Flashlight 12...

1 Answer

Wont take charge


How old is it?

Are you trying to charge it while it is hot?

2 or more years old ... it is done

Hot? Hot batteries will not charge.

Oct 15, 2009 | CRL 18 Volt Battery Cartridge for LD147...

1 Answer

Batteries will not charge


Ni-cad will go bad if they sit for a long time
before charged, now Ni-mi you can charge it
at any time,so next ask or look for NI-MI
they will know what you are talking about.
Hope this helps.

Sep 09, 2009 | Porter Cable-Cable PCL180DK-2 18-Volt...

1 Answer

I have a mikita 12 volt and when I charge it it wont hold charge.


do you have a volt meter toi check the charger voltage? if so then read the voltage out of the charger, it should be 1 or 2 volts higher than the listing 12v would be 13 or 14 volts. if it's working you probally do have a bad battery. if the charger is out then you have a bad charger.

Aug 03, 2009 | Makita 12 Volt Cordless Drill/Driver Kit

1 Answer

14.4V Drill Battery Will not Charge


The battery is 14.4 volts so the charger should be 14.4 volts.

Jun 26, 2009 | Makita 3/8" Dr. 14.4V Cordless Drill Kit

1 Answer

Zivan NG3 battery charger diagrams


Hi,
your NG3 should have been preprogrammed for the type of batteries you are charging. The NG3 has the 3 wires from the power cord. Here is what I have done:
Brown from charger goes to black wire
Blue goes to white wire
yellow green goes to green ground.

Mar 11, 2009 | Ryobi Multi-Volt Battery Charger

1 Answer

Batteries seems they do not charge. They show yellow &geen always


you need to open up you battery and check each on for voltage. take out the ones that have no voltage and resolder it with the good battery from your other non working one. you need to ruff up the top and bottom of the battery to solder a wire to it. make sure you dont touch the battery to the wrong polarity or you will get a spark or fire.

Nov 25, 2008 | Ryobi Multi-Volt Battery Charger

Not finding what you are looking for?
Drills Logo

Related Topics:

944 people viewed this question

Ask a Question

Usually answered in minutes!

Top Black & Decker Drills Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

JOHN LAPIER

Level 3 Expert

2428 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you a Black & Decker Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...