Question about Lands Phones

3 Answers

I have a Lucent a2011-2 analog teleset that recieves phone calls but when I try to dial nothing happens except the dial tones stays on. I reversed the polarity but it did not change anything. Need help

Posted by on

  • Dsull Oct 11, 2010

    I tried that several times and it had no effect. The seller sent me another telephone and it does the same thing.

  • Dsull Oct 12, 2010

    According to my phone company, our system is analog

×

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,216 Answers

It may be possible that you do not have tone dialling activated with your service network and previously you would be using pulse mode .
Look for this setting and change it to pulse.
If this did not work tell me so that we can check for other problems

Thanks.....

Posted on Oct 13, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Expert
  • 2,973 Answers

Where did you get such a phone from? What you need in today's digital world is a digital phone. With an analogue phone you can only receive calls but not send any. It is of no use these days. Even I had to throw away mine a long time back.

Posted on Oct 12, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,478 Answers

Hello,

Have you try to reset it? If no, Just try to reset it to factory settings.
Remove the AC Adapter from the AC power (either at the base or at the wall outlet) and immediately connect it again. Remove battery from the handset and immediately replace it. Place the handset back into the charger for about 5 seconds. That should reset the phone and put the phone on default.

Take care.

Posted on Oct 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why will my uniden phones not dial out, all units will not dial out. Phone jack works, but when I try to dial, with each digit pressed I only get a dial tone. Phone will receive calls, but I cannot dial...


I have not seen this in a long time. 'Way back in
the 1970's a similar problem would occur when the
telephone company accidently reversed the 'tip and
ring' wires.

This was only a problem with the
then-new "push button" (tone) dialing, the standad
rotary dials worked fine. The fix was to reverse
the red & green station wires in the "B-block"
(on the baseboard) to undo the central office goof.

Maybe it still happens? Try reversing the red &
green wires in the modular socket you are plugging
the base ('main unit') into.

Good luck!
------------

Feb 18, 2015 | Uniden Cordless Phone

1 Answer

Why won't my Uniden cord or cordless phone system dial out. with each digit pressed a dial tone is heard and nothing connects.


I have not seen this in a long time. 'Way back in
the 1970's a similar problem would occur when the
telephone company accidently reversed the 'tip and
ring' wires. This was only a problem with the
then-new "push button" (tone) dialing, the standad
rotary dials worked fine. The fix was to reverse
the red & green station wires in the "B-block"
(on the baseboard) to undo the central office goof.

Maybe it still happens? Try reversing the red &
green wires in the modular socket you are plugging
the base ('main unit') into.

Good luck!
------------

Feb 18, 2015 | Uniden Lands Phones

1 Answer

I can't get dial tone and can't dial out.


make sure the phone is plugged in. You'll need dialtone first, the other issue will fix themselves once you have dialtone!

Feb 10, 2010 | Lucent 1872 Corded Phone

1 Answer

Comdial Executech 6714x-PG We have nearly 20 phones. All of them get a dial tone but nothing happens when you press 9 to dial out, none of the phones will dial out. Calls can come in only. Thank you


they are either restricted or what you are hearing is intercom tone and not dial tone. the phones may be set to dial out from a diffrent line grop as well have you tried dialing 81 82 instead of 9 and see what happens

Jan 05, 2010 | Comdial 6714 14 Button Executech Phone

1 Answer

The phone does not want to work and I can not send out a fax


Need more information about this problem.
1. If you plug a phone in the wall is there a dial tone.
2. Can you recieve faxes.
3. If you can reset the machine, reset or initialize it.
4. With a analog phone plug it in that fax socet and try calling the phone to see if it rings. If it does the line is good.
5. If it does have a dial tone, suspect a modem board or main board defective.

Oct 15, 2009 | Lexmark Office Equipment & Supplies

1 Answer

MLX-10DP phone thinks there's a headset plugged into it


Try a different phone. The clicker switch could be bad on teh phone.

Jun 24, 2009 | Lucent Merlin Legend MLX-20L Phone

1 Answer

The phones worked last night, this morning nothing


If the phone rings but no dial tone, possible phone unit is faulty. I suggest to try a different phone unit to verify if it's faulty. If the other phone isn't working too, then report the issue to your phone provider.

Jun 10, 2009 | Linksys SPA-2102 NA Analog VoIP Adapter...

1 Answer

HP 4215


try connecting a normal phoneline to that line and try.
It might be a prob with long dist calls.

If u are ok with the phone test, check its in tone or pulse. Try switching. Then also if that is not working just reset the printer and try.

Mar 04, 2008 | HP Officejet 4215 All-in-One Color Photo...

3 Answers

Lucent Technologies 925 Phone


If memory serves, to program the touch tone, lift the handset, press [PROGRAM] # # # 3 then hang up.

May 24, 2007 | Lucent Speakerphone 925 (21248)

Not finding what you are looking for?
Lands Phones Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lands Phones Experts

kakima

Level 3 Expert

102366 Answers

Computer Repairing
Computer Repairing

Level 3 Expert

14641 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...